GE PSS26MGPBBB refrigerator - p series

OWNER’S MANUAL AND INSTALLATION - Page 12

For PSS26MGPBBB. Series: P serie
Also, The document are for others GE - General Electric models: PSS23MGPBBB, PSS25MGPBBB, PSS27MGPBBB, PSS29MGPBBB

PDF File Manual, 128 pages, Read Online | Download pdf file

PSS26MGPBBB photo
Loading ...
Loading ...
Loading ...
Aboutthe automatic icemaker.
A newly installed refrigerator may take 12to 24 hours to begin making ice.
On dispenser models, to Automatic Icemaker
access ice or reach the
power switch: The icemaker will produce sexen cubes
per cycle--al_proxinlately 100-130 cubes
-.-_-_--.-- in a 24-hour period, depending on freezer
COlnl)artnlent temperature, rooln
[_1 ii _ teillperattu'e, ntlillbei" of door ol)enings
o, ei-.sec.. litio.s.
,, If the reti_ioerator is o _erated before the
\. / s thepo,,eis,,.,hi. the0(o#)p,.si,o.
x¢,. / [ iI _._qaen the refl_Jgerator has been connected
to the water SUl)ply, set the power switch to
o Lift flTebin, flTenpull it
forward until the bin stops.
i i) i ii
Lower the bin to access ice
or reach the power switch.
NOTE:In order to take full advantage
of the tilt-out ice bin, only store items
on the shelf below the ice bin flTat
are no taller titan the lowest point
on the bin.
the I (on) position.
The icemaker Mll fill Mth water when it
cools to 1:5°l_ (-10°C), A newE, installed
refl_igerator may take 12 to 24 hotu_ to begin
making ice cubes,
Y_m will hear a buzzing sound each time
the icelnaker fills with water:
Throw awa_ the fiI_t few batches of ice to
allow the water line to cleai:
Be sure nothing inteil'bres with the sweep
of the feeler aml,
"_&q_enthe bin fills to the lmel of the feeler
aml, the icemaker will StOli_ _roducing
ice, It is nomlal fin" sexeral cubes to be
joined mgethei:
If ice is not used fi'equenfl}; old ice cubes
will become cloudy, taste stale and shrhlk.
Special notes about dispenser models:
_: Dispenser models have a tilt-out ice bin.
The bin can be tilted out as shown ill
the illustrations, and it will hold itself
up while you take ice out or turn tile
iceinaker power switch on and off.
Be sure to put the bin back ill place
betore closing the dooi;
::Ji::To restore your ice level from an empty
bucket stage, the following steps axe
recommended:
O 12 hom_ after the fii_t batch of ice
has tifllen into the bin, dispense
3 to 4 cubes.
@ _AJieI" an additional 6 houi_, dispense
3 to 4 ctlbes again.
These steps will restore your ice level
in the shortest amount of time.
Power
Switch
NOTE"In homes with lower-than-average water
pressure, youmay hear the icemakercyclemultiple
times when maklbgone batch of ice.
o Lift the bin, then pull it
forward until the bin stops.
Removing Ice Bin (dispensermodels)
CJIUTIOIV: The ice bin is heavy when full.
Set the power switch to the 0 (off) position
belin'e removing the bin.
When replacing the bin, be sure to press it
firefly into place. If it does not go all the
way back, remove it and rotate the drive
mechanisnl 1/4 turn. Then push the bin
back again.
Dispenser Models on v
Lift and pull forward again
to remove the bin.
/2
Loading ...
Loading ...
Loading ...