Loading ...
Loading ...
Loading ...
- 8 -
05/2020
Copyright © 2020, Fast ČR, a.s.
■ The SLEEP mode is a combination of the NATURAL mode (natural breeze) and
agradual lowering of the fan speed.
Fan setting Progression of the SLEEP mode
High speed The appliance will run for 30 minutes in the
NATURAL mode with the high fan speed set.
After 30 minutes, the high fan speed switches to
medium speed. After an additional 30 minutes,
it will switch to the low fan speed setting. The
appliance will remain in the NATURAL mode with
the low fan speed set.
Medium speed The appliance will run for 30 minutes in the
NATURAL mode with the medium fan speed set.
After 30 minutes, the medium fan speed switches
to low speed. The appliance will remain in the
NATURAL mode with the low fan speed set.
Low speed The appliance will run in the NATURAL mode with
the low fan speed set.
Water filter dryer function
■ This function serves exclusively for the purpose of drying out the water filter A10.
If you intend to store and not use the appliance for an extended period of time, it is
necessary to carefully dry out the water filter A10 and other parts to protect them
again the formation of mould.
■ Hold down button B2
for approx. 3 seconds to activate the dryer function. The
fan speed automatically changes to high speed and will run for 20 minutes. During
this time, it is not possible to change the settings of the appliance. Only button
B1
will remain functional. After 20 minutes have elapsed, the appliance will
automatically switch to the stand-by mode.
Note:
If the appliance is turned off with button B1
during the drying out
process, and then is turned on again, the appliance will start at the setting
that was set prior to the dryer function being set.
Setting automatic vertical flap motion
■ Button B6
serves to turn the automatic vertical flap motion on and off. Indicator
light B11 is lit to indicate that motion is activated. Press button B6
again to stop
the vertical motion of the flaps.
Setting the angle of the horizontal flaps
■ The angle of the horizontal flaps A2 can be set manually by tilting them up or down.
When handling them, be careful not to damage them.
Automatic shut-off function
■ The appliance is equipped with an automatic shut-off function after 15 hours of
non-stop operation. This means that after 15 hours of operation, during which no
control button is pressed, the appliance will turn off automatically.
■ If you wish to cancel this function, hold down button B6 for approximately
3 seconds. The appliance will beep and the automatic shut-off function will be
cancelled. If you wish to activate this function again, hold down button B6
for
approximately 3 seconds. The appliance will beep and the function will again be
activated.
Power-saving mode
■ The display will dim out after 1 minute of inactivity. This is normal. Pressing any
button will turn the display on again.
REMOTE CONTROL
■ The function of the buttons on the remote control A15 and the control panel A2 are
the same. If you wish to use the remote control A15, point it at the level of the signal
receiver A1 on the control panel A2. The maximum range of the signal transmitted
from the remote control A15 is 6 m.
Note:
If there are obstacles located between the remote control A15 and the
appliance, the signal may not be transmitted.
FILLING THE WATER TANK
■ Before filling the water tank A12, turn the appliance off, disconnect it from the
power socket and secure the appliance against moving.
■ Release the lock A13 by turning it to the horizontal position – see figure E1.
■ Take out the water tank A12 and fill it with clean cold water – see figure E2.
■ Insert the water tank A12 back into the appliance and turn the lock A13 to the
vertical position to secure the water tank A12 inside the appliance.
■ Always fill the appliance with clean cold water. To prevent undesirable bacteria,
micro-organisms or moulds from multiplying, do not leave water in it for more than
aday.
Warning:
When filling the appliance, make sure that the water level reaches
at least the minimum water level mark and also that it does no go
past the maximum mark.
Note:
When the appliance is used for the first time, you may register aslight
odour or discolouration of the water in the water tank A12. This is
anormal event that will disappear with use and which has no negative
effects on your health.
USING THE COOLING INSERTS
■ The cooling inserts A16 enable the temperature of the water in the water tank to be
reduced, which results in cooler air and faster cooling of the room.
■ Insert the cooling inserts A16 into afreezer for at least 12 hours. Then insert them
into the part of the water tank A12 that is marked with acooling insert symbol. Fill
the water tank A12 with water and insert the cooling insert A12 into the body of
the appliance.
■ The appliance is supplied with two cooling inserts A16, which ensures continuous
operation. You can use either one or both, as required.
Warning:
It is forbidden to open the lock of the cooling insert A16 or to
damage its external case in any way. The contents of the cooling
insert A16 is damaging to health. In the event of swallowing,
immediately seek medical help.
CLEANING AND MAINTENANCE
■ Disconnect the power plug from the power socket before cleaning.
■ For cleaning, do not use cleaning products with an abrasive effect, solvents, etc. that
could damage the appliance.
Warning:
To prevent the risk of injury by electrical shock, do not submerge
the appliance, power cord or power plug in water or any another
liquid.
CLEANING THE WATER TANK
■ When you have finished using the water tank A12, empty it out and rinse it with
clean water.
■ To remove limescale deposits and to prevent undesirable bacteria, micro-organism
or moulds from multiplying inside the water tank A12, clean it out at least once
per month using acloth dampened in lukewarm water with the addition of neutral
detergent. Then rinse it out thoroughly using clean water, dry it out using aclean
cloth.
CLEANING THE DUST AND WATER FILTER
■ Dirt and soils may accumulate on the dust filter A9 and water filter A10 during use,
which may negatively affect the operation of the appliance. We recommend that
these filters are regularly cleaned at least 1x per month. The frequency with which
the appliance is cleaned depends on its use. If it becomes excessively soiled, the
effectiveness of the appliance may be reduced.
1. Disconnect the power plug from the power socket.
2. Press the safety clip at the top of the dust filter A9 and tilt it out of the appliance
together with the water filter A10 – see figure F1.
3. Carefully take out both filters – see figure F2.
4. Take the water filter A10 out of the dust filter A9.
5. Wipe the dust filter A9 with asoft sponge lightly dipped in warm water with asmall
amount of neutral cleaning agent.
6. Soak the water filter A10 in warm water with asmall amount of neutral cleaning
agent. Then carefully wring it out in your hands and install it back into the dust filter
A9.
7. Insert both filters back into the appliance and turn on the dryer function (see
instructions in section "Water filter dryer function").
CLEANING THE OUTER CASE
■ To clean the outer case, use atextile lightly dampened in lukewarm water with an
addition of neutral detergent.
Storage
■ When not using the appliance for an extended period of time, disconnect the power
plug from the power socket and clean it according to the instructions in chapter
"Cleaning and maintenance".
■ Before storing it, check that the appliance and all its accessories are thoroughly
clean and dry.
■ Remove the battery from the remote control A14.
■ Store the appliance in a dry, clean and well-ventilated location not exposed to
extreme temperatures and out of children'sreach.
Loading ...