Loading ...
Store the vacuum by firmly pressing the
product into the wall mount to secure.
NOTE: Accessories can be stored by sliding
them onto the top of the wall mount.
Press to turn Machine On/O.
Press to turn Brush Roll On/O.
NOTE: We recommend that you turn the
Powered Floorhead Brush Roll OFF for
hard floors and ON for carpets. Using with
the Brush Roll OFF will extend runtime.
Boost Mode: Increases the suction power
to get a deeper clean.
2
Pull the filter away and tap to remove dirt.
Rinse filter under warm water until water is
clear. Allow filter to dry for 24 hours before
reinserting.
2
IMPORTANT: Avoid using solvents when
cleaning plastic parts. Most plastics are
susceptible to damage from various types of
commercial solvents and may be damaged
by their use. Use a clean cloth to remove dirt,
dust, oil, grease, etc.
EMPTYING THE DIRT CUP
GENERAL MAINTENANCE
WARNING:
To avoid serious
personal injury, always remove the
battery pack from the product when
cleaning or performing any maintenance.
CAUTION:
Put product away after
use to prevent tripping accidents.
CAUTION:
To avoid injury,
particularly to face and head, keep
hair, loose clothing, fingers and all
parts of the body away from revolving
brush.
CAUTION:
Not to be used for
grooming a pet.
1
2
3
Rock the dirt cup into the handheld.
Push the reach wand down onto the powered
nozzle until it clicks into place.
Push the handheld down onto the reach wand
until it clicks into place.
NOTE: Fully charge battery before first use. This
will take 3-4 hours. Due to federal regulations,
the battery does not come fully charged.
Fully assemble product prior to use.
WARNING:
Risk of personal
injury - Brush roll may suddenly restart.
Turn power switch off and remove
battery before cleaning or servicing.
1
2
Remove powered nozzle from reach wand.
Using a coin, push and turn the brush roll lock
counterclockwise to release the brush roll.
Pull the brush roll out of the powered nozzle.
To remove any threads or hair, slide the blade
of a pair of scissors into the groove of the
brush roll and cut along the groove.
CLEANING THE FILTER AND CYCLONE
REMOVING AND REPLACING THE
BRUSH ROLL
TROUBLESHOOTING
FIND AVAILABLE REPLACEMENT PARTS AND ACCESSORIES AT HOOVER.COM.
IF APPLIANCE IS NOT WORKING AS IT SHOULD, HAS BEEN DROPPED, DAMAGED, LEFT OUTDOORS, OR
DROPPED INTO WATER, CALL CUSTOMER SERVICE AT 1-800-406-2005 PRIOR TO CONTINUING USE.
SEE BEHIND THE BATTERY DOCK ON THE PRODUCT FOR MODEL NUMBER.
CHARGING
YOUR PRODUCT
OPERATION
1
1
1
2
2
3
Plug in the charger, then attach the battery
pack to the charger by aligning the ribs on the
battery pack to the grooves in the charger.
Press the handheld release button. Pull to
separate the handheld from the reach wand.
Press the powered nozzle release button and
pull to remove the powered nozzle from the
reach wand.
Push the chosen accessory into the handheld
until it clicks into place.
Push the accessory into the reach wand until
it clicks into place.
To remove the battery pack, press the latches
and pull up.
NOTE: During charging, the pack and ambient
temperature should be between 32 to 86° F (5
and 30° C). The charger will sense if the pack,
or ambient temperature, is too cold or too hot,
and will return an error code (red LED will be
on) and not charge the pack.
2
Slide the battery pack into the charger.
NOTE: The lights on the battery will show the
state of charge. If the light on the charger
flashes red, there is an error with the battery
or the charger. If this occurs, disconnect and
reconnect the battery or call customer service
for support. Once charge is complete, lights
on the battery and charger will turn o.
Clear any dirt/debris from the end caps and
inside the housing of the powered nozzle.
Re-fit the brush roll into the housing and turn
the brush roll lock clockwise to lock.
3
4
HANDHELD MODE
CLEANING UP HIGH
MAINTENANCE
1
Remove the battery pack.
ASSEMBLY
This product contains no serviceable parts.
If appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped into
water, call customer service at 1.800.406.9005 prior
to continuing use.
THERMAL PROTECTOR
A thermal protector has been designed
into your cleaner to protect it from
overheating. When the thermal protector
activates, the cleaner will stop running. If
this happens, proceed as follows:
1. Turn cleaner OFF and remove battery
pack
2. Empty dirt cup
3. Inspect the filter and cyclone for any
obstructions. Clear obstructions if present
4. After the battery pack is removed and
the motor cools for 30 minutes, reinstall
the battery pack. The thermal pr tector
will deactivate and cleaning may continue.
If thermal protector continues to activate
after following the above steps, call
Customer Service at 1-800-406-2005.
WALL MOUNT
ASSEMBLY
1
2
Choose the desired location, then place the
mount on the wall at the desired height. Mark
the wall anchor locations. Install the anchors
and screw the mount to the wall.
1
USING YOUR PRODUCT
1
3
Hold the dirt cup over a trash bin and press
the dirt cup release button to empty. Close
the dirt cup, then replace it by rocking it back
into place.
Push down the latch on the dirt cup to
release. Tilt and lift to remove the dirt cup
from the stick vac.
1
Pull open the lid of the dirt cup to access
the filter. To clean the cyclone, lift to remove.
Clean dirt and debris.
CLEANING THE FILTER AND CYCLONE
(CONT’D)
IMPORTANT: Do not use vacuum without the
filter or cyclone in place.
Do not use soap or other chemicals to clean.
Dry filter completely, for up to 24 hours,
before reinstalling into the product.
REMOVING AND REPLACING THE
BRUSH ROLL (CONT’D)
WARNING:
Risk of personal injury - Brush roll may suddenly restart.
Turn power switch off and remove battery before cleaning or servicing.
Loading ...
Loading ...
Loading ...