Loading ...
Portable use
WARNING: THE HEATER SHOULD NEVER BE USED AS A PORTABLE
APPLIANCE WITHOUT THE FEET SECURELY FITTED.
Lay the heater on its back and remove the wall mounting brackets - see
Wall mounting. Locate and remove the foot xing screw - see Fig. 2(a).
Clip the foot in place and secure using the foot xing screw.
NOTE – The wall mounting brackets must be removed before the foot
can be tted.
Wall Mounting (Installed)
Three identical wall mounting brackets are secured to the base of the heater
with a xing screw. To wall mount appliance, rst remove the brackets as
follows, lay the heater on its back and follow the sequence shown - see
Fig. 3. Identify and remove the xing screw securing the brackets located
beside mains cable as shown in (a), pull out brackets and rotate them to
disengage them from the slot and withdraw the brackets from the slot (b).
Select a suitable position, near to a mains power socket whilst ensuring
the minimum mounting clearances are maintained - see Fig. 1. Fix the
two top retaining brackets to the wall, using suitable xings – see Fig. 4.
574
Locate the heater on the top brackets and allow it to hang in place.
Fit the bottom bracket into the slot in the heater and then x it to the wall.
Test that the heater is now securely xed to the wall.
Controls
Neon
St
and By
LCD Displa
y
Te
mperature
Decr
ease
Te
mperature
Incr
ease
Desired
Temperature
Frost proteco
n
Symbol
Operating the Heater - ‘Control Mode’
With the product plugged in, press the ‘‘ ’ button. This will illuminate the
neon and also light up the LCD display. This indicates that the product is in
control mode, the desired room temperature can then be set.
Setting the ‘Desired’ Room Temperature
The temperature is set using the temperature increase ‘ ’ and temperature
decrease ‘ ’ keys - see Fig. 5. The room temperature can be set in the
range between 5°C to 30°C. The back light of the LCD will change colour
depending on the desired room temperature. (Blue screen 5 to 16, 17 to 19
green, 20 to 22 white, 23- 30 red). Please note the temperature setting is
for desired room temperature (not the actual room temperature).
‘Intelligent’ Eco Mode
This is the appliance default setting, the appliance will automatically start
up in this setting once power is applied and the standby key is pressed. The
LCD display will indicate the desired room temperature and the appliance
will automatically regulate the room temperature accordingly. In this mode
the appliance operates at full power, however the output of the appliance is
automatically reduced and regulated as the room temperature approaches
the desired level. This mode optimises energy use by calculating the most
efcient and effective way to achieve the desired temperature setting. The
desired room temperature can be adjusted at any time during operation by
pressing the appropriate key.
Standby Mode
With the heater ON if the ‘ ’ button is pressed, the heater will go into
standby mode, the heater switches off, the display goes blank and the
neon will switch off. On pressing the ‘ ’ button again the heater will come
on in the with the desired room temperature settings it had prior to going
into standby mode.
LCD Display
The LCD display shows the desired room temperature. When the appliance
is set to frost protection mode (5°C) the frost protection symbol ‘ ’ will be
displayed on the screen.
The colour of the display backlight will vary depending on the desired
temperature set (see notes above under ‘Setting the desired room
temperature’). The backlight will switch off a short period after the last key
press. Any additional key presses will re-illuminate the screen.
Indicator Neon
The control contains an indicator neon. This neon comes on to indicate
when the product is in ‘control mode’. This neon does not indicate if the
heat is on, if the room temperature is at the desired temperature then the
heat will be off but the control is still operating, the neon will remain on.
When the delayed start function is activated the neon will blink intermittently
to indicate the product is in delayed start mode. Once the delayed start
period has elapsed the neon will switch on to indicate the product is in
control mode.
Frost Protection Mode
The appliance has a frost protection mode. This setting is useful in areas
such as garages to assist in the prevention of frost damage. If the thermostat
is set to its minimum setting ‘5°C’, the heater will cycle ON and OFF to
maintain a temperature of approximately 5°C and help protect against frost
conditions. The frost protection symbol ‘ ’ will be displayed on the LCD
display when frost protection mode is activated.
Fig. 5
Fig. 4
Fig. 3
Fig. 2
Loading ...
Loading ...