Remington XR7000CDN Balder Pro Head Rotary Shaver User Manual

XR7000

Use and Care Guide

IMPORTANT SAFETY

INSTRUCTIONS

When using an electrical appliance, basic precautions should always

be observed, including the following. Please read all instructions

before using this shaver.

WARNINGS

To reduce the risk of burns, fire, electric shock, or injury to persons:

• When connecting the charging unit to a power source outside

of the USA or Canada, use a plug adapter suitable for the power

outlet. This device has a charging adapter that will work with

worldwide 100V-240V power outlets.

• Only use the power adapter provided with this device.

• Do not reach for the appliance if it has fallen into water while

plugged into the power source. Unplug from the power source at

the wall immediately.

• Shaver may be rinsed under water or used in the shower, but

never use the charging unit in the shower.

• Detach the shaver and charging unit from the power source

before cleaning.

• Except when charging, always unplug this appliance immedi-

ately after using.

• When recharging place in a safe position, out of the reach of

children and pets.

• Close supervision is necessary when this appliance is used by,

on, or near children or individuals with certain disabilities or

special needs.

• Use this appliance only for its intended use as described in this

manual.

• Do not use attachments not recommended or provided by the

supplier.

• Never operate this appliance if the electrical cord is frayed or

the plug is damaged.

• Keep the electrical cord away from heated surfaces.

• Never drop or insert objects into any of the appliances openings.

• This appliance is intended for household use only.

• Do not use outdoors, or operate where aerosol (spray) products

are being used, or where oxygen is being administered.

• Always attach the plug to the appliance, then to the wall outlet.

To disconnect, turn all controls to OFF, then remove plug from

outlet.

• Always pull on the plug body to unplug the appliance from the

wall socket. Never pull on the electrical cord.

• Do not plug in or unplug this appliance when your hands are wet.

• Do not use extension cords or a voltage converter with this

appliance.

• Do not wrap the power cord around the appliance.

• Always store the appliance and charger in low moisture area.

• Do not expose the appliance to temperatures over 140° F (60° C).

• Detach removable power cords from the appliance during storage.

• Do not use this shaver if the cutting head surfaces are damaged

or broken as skin injury could occur.

• This shaver and trimmer are intended for use on scalp hair only.

It should not be used for facial hair or longer hair on your body.

PRODUCT FEATURES

SHAVER PARTS

1. On/Off Switch

2. Shaving Head

3. Pop Up Trimmer (not shown)

4. 360° Pivoting Neck

5. LED Battery Indicators

6. Hair Pocket

7. Charging Pins

8. Power Adaptor

9. Head Guard

Also Includes:

• Cleaning Brush

• Shaver Lubricant

SAVE THESE INSTRUCTIONS

SPECIFICATIONS

GUIDELINES

• Do not attempt to shave head hair that is longer than 4 days

growth or 2.0 mm. The Ultimate Series Rx5 head shaver is

intended to maintain the shaved look and can be used daily or

every two or three days.

• The Ultimate Series Rx5 head shaver cannot shave long hair

down to the shaved length. If your hair is longer than 2.0 mm

you should trim it down with a hair clipper first before using the

head shaver.

• The Ultimate Series Rx5 head shaver can be used dry or it can

be used with shaving cream or gel in the shower.

1. Hold the head shaver body in the palm of your hand. Press the

On/Off switch to turn the head shaver on.

2. Press the five cutting heads against your scalp. It is not

necessary to press hard to shave. Pressing hard does not cut

closer and could increase irritation. The cutting head will flex to

follow the contours of your head.

3. Move the shaver slowly around your head. You may use linear

strokes, or rotating motion, whichever you feel is most effective

picking up and cutting your hair.

4. Use a hand held mirror to check the back of your head to

confirm a complete and thorough shave. You may also use your

other hand to feel for complete and consistent cutting.

5. It is not recommended to use the head shaver for facial hair.

6. When finished turn the shaver off. Check for the red low charge

indication.

SHAVING YOUR HEAD CHARGING

By registering your new Remington

product, you will receive special offers.

Power System Cordless

Initial Charge Time 4 Hours

Full Charge Time 4 Hours

Cordless Run Time Up to 50 Minutes

Indicators 2 LEDs (Low / Charging /

Full Charge)

Voltage Type Worldwide 100 - 240V

Waterproof Yes

Replacement Head and

Cutters

SPR-XR7000

Power System: Cordless - shaver can only be used when discon-

nected from the charging adaptor. The shaver will not run while it

is charging.

To preserve the life of the battery: do not charge the battery after

each use. The best practice is to use the shaver until the red low

charge indicator appears and then recharge.

Indicators:

• Low Charge: Flashes red when the shaver needs to be

recharged.

• Charging: When plugged in, the charging indicator will light up

green.

• Full Charge: Green LED indicator will turn off.

Note: Some countries will require the use of a plug adaptor that is

not included with your shaver.

Before using, read the important safety instructions in this manual.

1. Ensure the product is switched off. Connect the shaver to the

adaptor

2. Connect to a power outlet and charge for 4 hours when using

for the first time. This first charge is important to the shaver’s

battery life.

3. When plugged in, the charging indicator will light up green.

4. When empty, the battery should be charged for 4 hours for a full

charge and will provide up to 50 minutes of shaving time.

5. To preserve the life of the battery do not charge the battery after

each use. Best practice is to use the shaver until the red low

charge indicator appears and then recharge.

Caution:

• Make sure the shaver and your hands are dry when charging the

shaver.

• Always charge the shaver in a cool, dry place.



















The pop-up trimmer is located at the back of the shaver handle. It

can be used for trimming edges of beards, sideburns or ears.

1. To activate the trimmer, turn the shaver on. Slide the release

button for the trimmer down to pop the trimmer up (A).

2. Use cutting strokes in the direction opposite of the trimmers

spring release. (B)

3. When finished press the trimmer down and snap it back into the

stored position. (C)

Note: Lubricate teeth with oil every 6 months.

POP-UP TRIMMER

CLEANING YOUR SHAVER

The Balder Shaver is designed to collect all the hair clippings while

it cuts. This avoids clippings from spilling onto bathroom counters

or shower stalls, making clean up easy.

• When cleaning the shaver make sure it is turned off and

disconnected from the charging adapter cord.

• The shaver is washable and can be cleaned by rinsing under

warm water.

• When using shave creams or gels with the shaver it is especially

important to clean after each use to prevent the gel from drying

and clogging the cutters.

When your rechargeable shaver reaches the end of its useful life,

the batteries must be removed from the shaver and be recycled

or disposed of properly in accordance with your state and local

requirements. If this is not required by law, you may elect to dis-

pose of the shaver with the batteries.

CAUTION! Do not put in fire or mutilate your batteries when dis-

posing as they may burst and release toxic materials. Do not short

circuit as it may cause burns. Dispose of properly in accordance

with your local and state requirements.

To Remove the Rechargeable Battery:

1. Unplug the shaver

2. Run shaver until the motor stops

3. Pull off the shaver head assembly.

4. Unscrew the screw on the top of the unit.

5. Pry off the upper decorative panel.

6. Pry off the two decorative side panels.

7. Unscrew the 6 screws on the inner housing.

8. Pry off the inner housing to expose the printed circuit board.

9. Take out the printed circuit board assembly.

10. Disconnect the battery from the circuit board.

11. Dispose of battery properly

PRODUCT DISPOSAL

100-240V AC, 50/60Hz Type: R17A

Questions or comments: Call 800-736-4648 in the U.S or Canada. Or visit

RemingtonProducts.com

®/TM are owned by Spectrum Brands, Inc.

Dist. by: Spectrum Brands, Inc., Middleton, WI 53562

Dist. by: Spectrum Brands Canada Inc.

255 Longside Drive, Unit 101

Mississauga, ON L5W 1L8

Made in China

T22-0005681-B

SHAVER REPLACEMENT PARTS

Please refer to the specifications’ table in this manual that lists the

correct replacement part number for your shaver.

It is very important to replace the shaving heads and cutters when

necessary to ensure a close, comfortable shave

without irritation. We recommend they be replaced

every 12 months. Here are some signs of head and

cutter wear, indicating that replacement is needed:

• Irritation: As the heads get excessively worn you may experience

some skin irritation. This would be especially noticeable when

you apply moisturizing lotion.

• Pulling: When the cutters wear you may feel a sense of pulling

and a loss of closeness when you shave. This is an indication

that it is time to replace the shaving heads and cutters.

The replacement cutting head for your shaver is model

number SPR-XR7000.

How to Order Parts and Accessories

• Order Online: RemingtonProducts.com

Limited Three-Year Warranty

Spectrum Brands, Inc. warrants this product against any defects that are due

to faulty material or workmanship for a three-year period from the original date

of consumer purchase. This warranty does not include damage to the product

resulting from accident or misuse.

If the product should become defective within the warranty period, we will

replace it free of charge. Return your product and sales receipt with your name,

address and day time phone number to: Remington Returns Center, 507 Stokely

Dr., P.O. Box 1, Deforest, WI 53532. For more information call 800-736-4648 in

the U.S. or Canada.

KEEP ORIGINAL SALES RECEIPT AS PROOF OF PURCHASE FOR WARRANTY PURPOSES.

This warranty does not cover products damaged by the following:

■ Accident, misuse, abuse or alteration of the product

■ Servicing by unauthorized persons

■ Use with unauthorized accessories

■ Connecting it to incorrect current and voltage

■ Any other conditions beyond our control

No responsibility, obligations, or liability is assumed for the installation or

maintenance of this product.

SPECTRUM BRANDS, INC. SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL,

SPECIAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS

PRODUCT. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO IM PLIED

WARRANTIES OF FITNESS AND MERCHANTABILITY, ARE LIMITED IN DURATION

TO THREE YEARS FROM DATE OF ORIGINAL PURCHASE.

This warranty gives you specific legal rights and you may also have other rights

which vary from state to state or province to province. Some states do not allow

the exclusion or limitation of incidental, special or consequential damages.

This warranty shall not be valid where it is contrary to U.S. and other appli-

cable laws, or where the warranty would be prohibited under any economic

sanctions, export control laws, embargos, or other restrictive trade mea-

sures enforced by the United States or other applicable jurisdictions. This

includes, without limitation, any warranty claims implicating parties from,

or otherwise located in, Cuba, Iran, North Korea, Syria and the disputed

Crimea region.

WARRANTY

Spectrum Brands, Inc. Money-back Offer

If within 30 days after you have purchased your Remington

branded product from

an authorized source, you are not satisfied and would like a refund, return it with the

sales receipt indicating purchase price and date of purchase to the retailer from whom

it was purchased. Spectrum Brands, Inc. will reimburse all retailers who accept the

product within 30 days from the date of purchase. If you have any questions concern-

ing the money-back guarantee, please call 800-736-4648 in the U.S. or Canada.

Remington Guarantees Satisfaction After 30 Days!

Remington 60-Day Money Back Guarantee*

If within 60 days after purchasing any Remington

product, you are not

completely satisfied and would like a refund, return it with the original dated

sales receipt directly to Remington and receive a full refund.** For questions

concerning the money-back guarantee, please call 800-736-4648 in the U.S. or

Canada.

*Applies to U.S. and Canadian customers’ returns only.

**Terms and conditions apply.

1. Refund will be in the form of a check issued in U.S. Dollars and will be provided

only if all Terms and Conditions are met.

2. The following items must be returned to Remington and postmarked no later

than 60 days after purchase of the Remington

product:

a. The Remington

product;

b. The original sales receipt indicating price and date purchased; and

c. The completed 60-day money back guarantee form located at

RemingtonProducts.com/60day.

3. In addition, Remington, in its discretion, must determine that the returned

product was used in accordance with the instruction booklet (included with the

product at the time of purchase).

4. Returns should be mailed prepaid (no collect returns accepted) to:

Remington 60-Day MBG

507 Stokely Drive, Box 1

DeForest, WI 53532

5. Refund does not include postage costs for the return of the product, but will

include applicable taxes paid by customer, if any.

6. No responsibility will be accepted for late, lost, stolen, misdirected or damaged product.

7. Please allow 4–6 weeks to receive your refund by check.

Contains a Listed Adaptor

A B C

D E F

After every use:

1. Hold the shaver over the garbage can and remove the top of the

cutting head. Remove the head by gripping in the areas between

the four outer cutters and pulling up and away from the handle. (D)

2. Tap the excess clippings that have been collected inside the hair

pocket into the garbage can. (E)

3. Rinse the cutting head thoroughly by running water through the

cutters from both sides of the head.

4. Rinse the hair pocket under running water.

5. Leave the cutting head detached and let it air dry. Reattach the

shaving head when dry and you are ready for the next use. (F)

6. Important: Lubricate the cutters on the inside surface with

one drop of lubricant per cutter once per week to maintain

performance.

TROUBLESHOOTING

If the shaver is making a chugging noise, clean and re-lubricate

the underside of the cutting heads. Be sure to clean shaver after

each use and lubricate weekly.

XR7000_27989_IB_EnFr-revB.indd 1XR7000_27989_IB_EnFr-revB.indd 1 6/2/20 2:10 PM6/2/20 2:10 PM