Loading ...
Loading ...
Loading ...
Remote Bluetooth Operation
The appliance can be controlled remotely using a smartphone or similar
device. To facilitate this remote operation it is necessary to rst download
the Dimplex app. The app is available on both android and IOS
devices and is available free from the Apple or Android App store. The
App is compatible with Android version 4.3 and above and IOS version
5 and above.
Once the App has been downloaded it is necessary to pair the appliance
with the smartphone to complete the remote setup. Please follow the steps
shown below:
1. Launch the Dimplex app on the smartphone or similar device.
2. To initiate pairing mode on the appliance press and hold the ‘ ’ button
for two seconds. The LCD screen will go blank with the exception of the
Bluetooth logo ashing in the bottom right hand corner, See Fig.13.This
indicates that the device is advertising to be paired with the app.
3. On the smart phone the appliance should now be visible on the pairing
screen, this will be a unique 6 digit code but will always start with EC, for
example ‘ECBC17’. Select this device and press connect to initiate pairing.
4. Once the paring process is complete the app can be used to control
the appliance.
5. Once paired successfully the Bluetooth logo will stop ashing and the
Bluetooth neon will be illuminated.
Flashing
Safety – overheat protection
For your safety, this appliance is tted with a thermal cut-out. In the event
that the product overheats, the cut-out switches the heater off automatically.
To bring the heater back into operation, remove the cause of the overheating,
then unplug or turn off the electrical supply to the heater for a few minutes.
When the heater has cooled sufciently, re-connect and switch on the
heater.
Fig. 13
The product complies with the European Safety Standards EN60335:2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014:1,
EN55014:2, EN61000:3-2 and EN61000:3-3 which cover the essential requirements of EMC Directive 2006/95/EC and the LVD Directive 2004/108/EC.
Important Notes
Although this heater is manufactured to comply with the relevant safety
standards, certain types of carpets could become discoloured by the
temperatures under a portable heater. If you are concerned about this,
we recommend that you contact the carpet manufacturer for guidance.
Alternatively, either stand the heater on a suitable base to shield the carpet
or wall-mount it – call our Helpline for further advice.
You may notice some parts of the element appearing to be hotter from time
to time because of the variable airow through the heater. This does not
cause a safety hazard.
The heat outlet grille may become discoloured with use – this is caused by
airborne pollution and is not a fault.
Recycling
For electrical products sold within the European Community.
At the end of the electrical products useful life it should not be
disposed of with household waste.
Please recycle where facilities exist.
Check with your Local Authority or retailer for recycling advice
in your country.
Cleaning
WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY
BEFORE CLEANING THE HEATER.
Before commencing cleaning, switch off the heater and allow it to cool.
Disconnect the electricity supply to the appliance.
The outside can be cleaned by wiping it over with a soft damp cloth and
then dried. Do not use abrasive cleaning powders or furniture polish, as
this can damage the surface nish.
To release the heater from the wall bracket for cleaning or redecoration,
depress latch on each bracket and hinge forward.
After Sales Service
Your product is guaranteed for three years from the date of purchase.
After sales information or assistance with this product can be found on
our website www.dimplex.co.uk/support.
Your rights under this guarantee are additional to your statutory rights,
which in turn are not affected by this guarantee.
Please do not return a faulty product to us as this may result in loss or
damage and delay in providing you with a satisfactory service.
If following these steps your product still does not operate you should
return it to your point of purchase.
Please retain your receipt as proof of purchase.
Model Identier(s):
403BTB 403BT
Heat output
Nominal heat output Pnom 3.0 3.0
kW
Minimum heat output (indicative) Pmin 1.0 1.0
kW
Maximum continuous heat output Pmax,c 3.0 3.0
kW
Auxiliary electricity Consumption
At nominal heat output elmax 0.0 0.0
kW
At minimum heat output elmin 0.0 0.0
kW
In standby mode elSB 0.0005 0.0005
kW
Type of heat output/ room temperature control
With mechanical thermostat room temperature control
Yes
Contact details GDHV, Milbrook House, Grange
Drive, Hedge End, Southampton,
SO30 2DF