Loading ...
Installation
The towel rail must be permanently fitted to the wall.
The rail must be so mounted that the top is at least 5Omm/2" below
any overhanging surface. Sufficient space must be left for access
to the terminal cover screws without removing the rail from the wall.
The rail can be mounted facing left or right, with the cable entry
position at the bottom.
Wall mounting
Procedure for fixing Wall Brackets
Step 1
Mark the hole position (x) - see Fig. 1 - for the first fixing bracket and
drill and plug the wall to suit. Fit the wall mounting bracket.
Step 2
Place the mounting strap carefully around the lower rail - see Fig. 3.
Securely fix it by screwing in place fully the M4 x 10mm screw.
Ensure the bracket is fitted with the rear of the strap facing directly
backwards.
Step 3
Place the mounting strap into the wall mounted bracket, secure it
with the locater pin by inserting it and giving it a quarter turn - see
Fig. 3.
Note: Take care and hold the towel rail in position as one bracket is
not sufficient to secure the towel rail to the wall.
Step 4
You now have a fixed point to help you mark the other hole positions
for the other two wall mounting brackets. Remove the locater pin,
and place towel rail carefully to one side to allow you to repeat Steps
1, 2 and 3, for the other brackets.
Fig. 3
To replace Cable
WARNING - The cable should only be replaced by a service
agent or a similary qualified person.
To gain access to the terminals first remove the two screws holding
the cover in position. These screws are on top and underneath.
Remove the screw from the bottom moulding. Remove the top cover
with the neon lens and connect the wires as shown in Fig. 4 below.
Fig. 4
(c)
wall mounting
bracket
(a)
mounting
strap
phillips head
screwdriver
flat head
screwdriver
(b)
screw M4x10
(d)
locater pin
rotated quarter
turn to lock
The Wall mounting pack contains:
(a) 3 mounting straps
(b) 3 screws (M4 x 10)
(c) 3 wall mounting brackets
(d) 3 locater pins
Fig. 2
Cleaning
The finish on your towel rail can be maintained by occasionally
wiping over with a damp cloth and lightly finishing with a soft dry
cloth. This should only be carried out when the rail is cold. Do not
use abrasive cleaning powders as this could damage the surface
finish.
Recycling
For electrical products sold within the European Community.
At the end of the electrical products useful life it should not
be disposed of with household waste. Please recycle
where facilities exist. Check with your Local Authority or retailer for
recycling advice in your country.
After Sales Service
Your product is guaranteed for two years from the date of purchase.
Within this period, we undertake to repair or exchange this product
free of charge (subject to availabilitiy) provided it has been installed
and operated in accordance with these instructions.
Your rights under this guarantee are additional to your statutory
rights, which in turn are not affected by this guarantee.
Should you require after sales information or assistance with this
product please go to www.dimplex.co.uk where you will find our
self help guide by clicking on “After Sales” or ring our helpdesk on
0845 600 5111 (UK) or 01 842 4833 (R.O.I.) .
Spare parts are also available on the website
www.dimplex.co.uk
Please retain your receipt as proof of purchase.
mounting
bracket
mounting
strap
lower rail
First mounting
strap position
Dimplex UK Ltd.
Millbrook House
Grange Drive
Hedge End
Southampton
Hampshire. SO30 2DF
The product complies with the European Safety Standards EN60335-2-46 and the European Standard Electromagnetic Compatibility (EMC) EN55014,
EN60555-2 and EN60555-3. These cover the essential requirements of EEC Directives 2006/95/EC and 2004/108/EC
TEL: 0845 600 5111
FAX: 01489 773050
WEBSITE: www.dimplex.co.uk
Republic of Ireland Tel. 01 8424833
[c] GDC Group Ltd,
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of Dimplex.
A division of GDC Group Ltd,