Loading ...
Loading ...
Loading ...
Heat Controller Room Air Conditioner with R-410A Owner’s Manual
14
INSTALLATION INSTRUCTIONS
Wall Sleeve Brands:
#7 Whirlpool ( 23 Deep)
1. Remove existing rear grille as shown on Page
6 of this manual and replace with provided
louvered rear panel. Install as shown here.
NOTE: You may need to drill holes in flange of
existing sleeve to match new rear grille.
2. Place (2) 1 x1 x14 seals against each side.
3. Gently slide unit in and check if amount extend-
ing from the sleeve is sufficient once the trim
frame is attached.
4. If position is Ok, remove unit and proceed to
the next step. If not go to step 9.
5. Attach (1)1 x1 x25 long seal in the center
at the top of the sleeve. Remove the backing
paper and press into position.
6. Attach (2) 1 x1 x14 seals to the left and
right sides of the sleeve.
7. Cut (2) 1 x x25 long seals to 14 long
and attach to the vertical sections of the grille as
shown.
8. Attach the tapered spacer blocks to the floor of
the sleeve. Now go to step 15.
Use these next steps if the unit requires extra
extension into the room.
9. Attach 1 x x14 long seal over the solid
vertical portion of the rear grille.
10. Attach (2) 4 x3 x1 foam blocks with the
slot overlapping the seal above.
11. Install the divider into the slots of the foam
blocks. You may need to trim the length to size.
12. Repeat steps 9-11 for the other vertical shown
portion of the grille as shown in the picture.
13. Attach (2) 1 x1 x14 seals along the sides
of the sleeve again making sure all seals are
flush.
14.Cut the 1 x1 x25 seal to fit the top of the
sleeve. The pieces must be fitted flush to the
edge of the divider.
15. Center unit and gently slide unit into sleeve.
16. Before sliding all-the-way back, remove 1st
screw from front on left side of unit.
17. Remove the plastic washer from the screw.
18. Screw and attach the other end of the ground
wire to the unit as shown in picture. Make sure
that the toothed washer is against the cabinet.
19.Slide the unit completely to the rear to ensure
a good seal, making sure the ground wire does
not become tangled.
20.Seal & Frame the unit as described on page 17.
21. If you have difficulty with mounting the grill to
the sleeve, follow the instructions for direct
mounting on Page 16.
Because of the increased unit depth, first try
dry fitting using the method described below:
1
/
2
1
/
2
1
/
2
3
/
8
3
/
4
3
/
4
3
/
4
3
/
4
1
/
2
6
5
12
9
11
13
10
14
1
/
2
7
4
4
4
4
3
8
3
8
4
4
7
13
#7 Whirlpool - 23” Deep
1. Remove existing rear grille as shown on Page 6 of
this manual and replace with provided louvered rear
panel. Install as shown here. NOTE: You may need to
drill holes in ange of existing sleeve to match new
rear grille.
2. Place (2) 1” x 1-1/2” x 14” seals against each side.
3. Gently slide unit in and check if amount extending
from the sleeve is sufcient once the trim frame is
attached.
4. If position is Ok, remove unit and proceed to the next
step. If not go to step 9.
5. Attach (1) 1” x 1-1/2”x 25” long seal in the center at
the top of the sleeve. Remove the backing paper and
press into position.
6. Attach (2) 1” x 1-1/2” x 14” seals to the left and right
sides of the sleeve.
7. Cut (2) 1” x 3/8” x 25” long seals to 14” long and
attach to the vertical sections of the grille as shown.
8. Attach the tapered spacer blocks to the oor of the
sleeve. Now go to step 15. Use these next steps if
the unit requires extra extension into the room.
9. Attach 1” x 3/4” x 14” long seal over the solid
vertical portion of the rear grille.
10. Attach (2) 4-3/4” x 3-3/4” x 1-3/4” foam blocks with
the slot overlapping the seal above.
11. Install the divider into the slots of the foam blocks.
You may need to trim the length to size.
12. Repeat steps 9-11 for the other vertical shown
portion of the grille as shown in the picture.
13. Attach (2) 1” x 1-1/2” x 14” seals along the sides of
the sleeve again making sure all seals are ush.
14. Cut the 1” x 1-1/2” x 25” seal to t the top of the
sleeve. The pieces must be tted ush to the edge of
the divider.
15. Center unit and gently slide unit into sleeve.
16. Before sliding all-the-way back, remove 1st screw
from front on left side of unit.
17. Remove the plastic washer from the screw.
18. Screw and attach the other end of the ground wire
to the unit as shown in picture. Make sure that the
toothed washer is against the cabinet.
19. Slide the unit completely to the rear to ensure a good
seal, making sure the ground wire does not become
tangled.
20. Seal & Frame the unit as described on page 17.
21. If you have difculty with mounting the grill to the
sleeve, follow the instructions for direct mounting on
Page 16.
Downloaded from www.ManualsFile.com manuals search engine
Loading ...
Loading ...
Loading ...