Loading ...
IMPORTANT SAFETY INFORMATION
It is most important that this instruction book should be retained with the appliance for future refer-
ence. Should the appliance be sold or transferred to another owner, or should you move house and
leave the appliance, always ensure that the book is left with the appliance in order that the new owner
can get to know the functioning of the appliance and the relevant safety information.
This information has been provided in the interest of safety. You MUST read it carefully before
installing or using the appliance.
Installation
¥ This appliance is heavy. Care should be taken
when moving it.
¥ It is dangerous to alter the specifications or attempt
to modify this product in any way.
¥ Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Important: if the supply cable is damaged, it must
be replaced by a special cable available from your
local Service Force Centre.
¥ Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
¥ Parts which heat up should not be exposed.
Whenever possible, the back of the appliance
should be close to a wall but leaving the required
distance for ventilation as stated in the installation
instructions.
¥ The appliance should be left for 2 hours after instal-
lation before it is turned on, in order to allow the
refrigerant to settle.
Child Safety
¥ Do not allow children to tamper with the controls or
play with the product.
¥ Keep all packaging well away from children.
During Use
¥ This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs only.
¥ Frozen food must NOT be re-frozen once it has
thawed out.
¥ Do not place carbonated or fizzy drinks in the freez-
er.
¥ Do not remove items from the freezer if your hands
are damp/wet, as this could cause skin abrasions
or frost/freezer burns.
¥ Ice lollies can cause Ôfrost/freezer burnsÕ if con-
sumed straight from the freezer.
¥ ManufacturersÕ storage recommendations should be
strictly adhered to. Refer to relevant instructions.
¥ The cooling plate or refrigerated freezer shelves in
this appliance contain channels through which the
refrigerant passes. If these are punctured this will
cause substantial damage to the appliance and
result in food loss. DO NOT USE SHARP
INSTRUMENTS to scrape off frost or ice. Under
NO circumstances should solid ice be forced off
the lining or shelves. Solid ice should be allowed
to thaw, when defrosting the appliance. See
Defrost Instructions.
Maintenance and Cleaning
¥ Switch off and unplug the appliance before carry-
ing out any cleaning or maintenance work.
Servicing
¥ This product should be serviced by an authorised
engineer and only genuine spare parts should be
used.
¥ Under no circumstances should you attempt to
repair the machine yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Refer to your local
Electrolux Service Force Centre and always
insist on genuine spare parts.
At the end of the
Appliance Life
¥ When disposing of your appliance, use an autho-
rised disposal site.
¥ Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
2
19
Door reversal
1. Disconnect from the electricity supply;
2. Remove all loose item, including food, store food
in a cool place;
3. Gently lay the fridge/freezer on its back with the
top held away from the floor by 5-8 cm (2-3 inch-
es) of packing;
4. Remove the feet (2-3).
5. Unscrew the bottom hinge (1).
6. Slide out the lower door from middle hinge (H)
and remove the latter.
7. Slide out the upper door from pin (D), unscrew
the latter and then screw it down into the hinge
provided on the opposite side, after having
removed the small plugs which should then be fit-
ted on the opposite side.
8. Refit the upper door and the middle hinge on the
opposite side.
9. Screw down the bottom hinge (1) on the opposite
side by using the screws previously removed.
10.Refit the feet (2-3) on the opposite side.
11.Unscrew the handles. Refit them on the opposite
side.
12.The doors can be aligned by adjusting the mid-
dle hinge.
13.The middle hinge can be adjusted horizontally,
with the help of a tool, after having slackened the
two screws.
Attention
After completion of the door reversing operation,
check that the door gasket adheres to the cabinet. If
the ambient temperature is cold (i.e. in Winter), the
gasket may not fit perfectly to the cabinet. In that
case, wait for the natural fitting of the gasket or
accelerate this process by heating up the part
involved with a normal hairdryer on a low setting.
H
D
D590
PR04
D715 PIED/M
1
2
3
Loading ...
Loading ...
Loading ...