Loading ...
Loading ...
2.Convertsurfaceburnersfor LP/Propane gas:
_ Unlike the standard gas range, THiS COOKTOP IS
NOT REMOVABLE. Do not attempt to remove this cooktop.
Save the natural gas orifices removed from the appliance for possible
future conversion back to natural gas.
For all burner locations:
a. Remove burner grates & burner caps.
b. Use your hand to remove the burner heads.
c. Remove the factory installed natural gas orifices from the center of
the orifice holders using a 7 mm nutdriver (See Fig. 6).
d. Replace the orifice in each of the orifice holders with kit supplied
LP/Propane gas orifice (refer to the LP Kit chart listed on page
1; also refer to Fig, 5 for the correct LP orifice installation at
each of the surface burner locations). Tighten each orifice until
snug. Use CAUTION not to overtighten.
e. Replace all the burner heads & caps. Match the letter located
under center of burner cap with letters located inside the burner
heads (center position is not marked - See Figs. 4 & 5).
f. Match the letter stamped on the burner skirt with the burner head
and burner cap (center position is not marked). Each of the burner
heads MUST have a burner cap installed to insure proper ignition
and gas flame size. Note: The burner electrodes must be located
properly in slot of each burner head (See Fig. 4).
Use caution when
replacing each
burner cap so the
electrode is not
damaged.
Burner
Cap
inner
Locatinc
Ring
Burner
Head
7ram
Nut
Driver
Holder
Fig, 6
3. Convert oven burner orifice for LP/Propane Gas 16,000
BTU*
a. Locate the oven burner spud (See Fig. 7).
b. Using a 1/2" wrench, turn down the adjustable spud, which injects gas
into the oven burner, until snug against the LP/Propane metering pin
(approximately 2-1/2 turns). DO NOT over tighten.
4.Convert waist-high broiler burner orifice for LP/Propane
Gas (13,500 BTU*) m
a. Open the oven door.
b. Locate the broiler burner spud and turn down until snug against the
LP/Propane metering pin (approximately 1 to 1-1/2 turns). DO NOT
over tighten (See Fig.7).
5. Reconnect gas & electrical supply to appliance
Leak testing of the appliance shall be conducted according to the
installation instructions provided with the appliance.
........................................
Waist-High Broil
Burner Orifice/
Self-Clean Models
Pin
Oven Burner
Orifice
Fig. 7
Checking Manifold Gas Pressure
if it should be necessary to check the manifold gas pressure, remove the
burner and connect a manometer (water gauge) or other pressure device
to the top right front burner orifice. Using a rubber hose with inside diameter
of approximately 1/4," hold tubing down tight over orifice. Turn burner
valve on. For an accurate pressure check, have at least two (2) other
surface burners burning. Be sure the gas supply (inlet) pressure is at least
one inch above specified range manifold pressure. The gas supply
pressure should never be over 14" water column. When properly adjusted
the manifold water column pressure is 10" for LP/Propane gas or 4" for
Natural gas.
Do not use a flame to check for gas leaks.
a. Disconnect the range and its individual shut-off valve from the gas
supply piping system during any pressure testing of that system at
test pressures greater than 14" of water column pressure
(approximately 1/2" psig).
b. The appliance must be isolated from the gas supply piping system
by closing its individual manual shut-off valve during any pressure
testing of the gas supply piping system at test pressures equal to or
less than 14" of water column pressure (approximately 1/2" psig).
%
To
Surface
Burner
Burner Flame Size _I 5/8" i{ -
MainTop
Fig. 9
6. Test to verify if "LOW" setting should be adjusted:
a. Push in & turn control to LITE until burner ignites.
b. Push in & quickly turn knob to LOWEST POSiTiON.
c. if burner goes out, reset control to OFF.
d. Remove the surface burner control knob.
e. Insertathin-bladedscrewdriverintothehollowvalvestemandengage
the slotted screw inside. Flame size can be increased or decreased with
the turn of the screw. Turn counterclockwise to increase flame size.
Turn clockwise to decrease flame size. (See Figs. 8 & 9).
Adjust flame until you can quickly turn knob from LITE to LOWEST
POSiTiON without extinguishing the flame. Flame should be as small as
possible without going out.
Loading ...