Loading ...
Loading ...
Loading ...
4
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).
If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED ashes rapidly 3 times
and beeps will sound. The option will not be enabled.
DELAY
The start time of the program may be delayed for a period of
time between 1 and 12 hours.
1. Press the DELAY button: the corresponding «h» symbol
appears on the display; each time you press the button,
the time (1h, 2h, etc. up to max. 12h) from the start of the
selected wash cycle will be increased.
2. Select the wash program, press the START/PAUSE button
and within 4 seconds close the door: the timer will begin
counting down.
3. Once this time has elapsed, the indicator light «h» switches
o and the wash cycle begins.
To adjust the delay time and select a shorter period of
time, press the DELAY button. To cancel it, press the button
repeatedly until the selected delayed start indicator light «h»
switches o.
The DELAY function cannot be set once a wash cycle has
been started.
TURBO
This option can be used to reduce the duration of the main
programs while maintaining the same washing and drying
performance levels.
After selecting the program, press the TURBO button and the
indicator light will switch on. To deselect the option, press the
same button again.
EXTRA DRY
To improve the drying of the dishes, after selecting the
program, press the EXTRA DRY button and the indicator light
comes on.
A higher temperature during the nal rinse and an extended
drying phase allow for improving drying. To deselect the
option, press the same button again. The EXTRA DRY option
results in the lengthening of the wash cycle.
TABLET (Tab)
This setting allows you to optimize the performance of the
program according to the type of detergent used.
Press the START/PAUSE button for 3 seconds (the correspon-
ding symbol will light up) if you use combined detergents in
tablet form (rinse aid, salt and detergent in 1 dose).
If you use powder or liquid detergent, this option should
be o.
ZONE WASH 3D
Option works with one rack at once. In particular, we
recommend to use it with Normal and Intensive cycles - thanks
to the additional 3D water jets placed on the bottom of the
cavity, ZONE WASH 3D option allows to save energy or to
increase the washing performance of the dishwasher:
• ZONE WASH 3D + NORMAL CYCLE: it allows to reduce energy
consumption up to 40%.
• ZONE WASH 3D + INTENSIVE CYCLE: it increases the washing
performances up to 40%. Ideal for very soiled mixed loads,
e.g. pans and saucepans, dishes with heavy encrustation
or dicult-to-clean crockery (grater, vegetable mill, dirty
cutlery).
How to activate the option:
1. Select a compatible cycle
2. By default the appliance washes dishes in all racks. To wash
only the specic rack, press this button repeatedly:
shown on the display (only lower rack)
shown on the display (only upper rack)
shown on the display (option is OFF and the appliance will
wash dishes in all racks).
Remember to load the upper or lower rack only, and to
reduce the amount of detergent accordingly.
OPERATION INDICATOR
A LED light projected on the oor indicates that the dishwasher
is working. One of the following operating modes can be
selected:
a) Disabled function.
b) When the cycle starts the light goes on for few seconds,
stays o during the cycle and ashes at the end of the cycle.
c) The light stays on during the cycle and ashes at the end of
the cycle (default mode).
If the delayed start was set, the light goes on either for the rst
few seconds or the entire duration of the countdown, based
on whether mode b) or c) was set.
The light goes o every time the door is opened. To select the
mode you prefer, switch on the machine, hold down button
P until one of the three letters appears on the display, press
button P until you reach the desired letter (or mode), hold
down button P to conrm the selection.
Loading ...
Loading ...
Loading ...