Loading ...
Before you start...
Important: If your washer and dryer
are already installed, they MUST be
uninstalled.
If you need to uninstall your washer or
dryer, see Installation Instructions that
came with your model for tools
required.
Excessive Weight Hazard
Use two or more people to move
and uninstall washer.
Failure to do so can result in back
or other injury.
WARNING
Explosion Hazard
Keep flammable materials and
vapors, such as gasoline, away from
dryer.
Place dryer at least 18 inches
(45.7 cm) above the floor for a
garage installation.
Failure do to so can result in death,
explosion, or fire.
WARNING
1.Turn off the hot and cold water
faucets.
2.Unplug the power supply cord.
3.Slowly loosen the fill hoses at the
faucets to relieve the water pressure.
Use a sponge or towel to absorb the
released water.
4.Remove the “HOT” and “COLD” fill
hoses from the back of the washer.
Drain water in the hoses into a bucket.
5.Squeeze the ears of the drain hose
clamp with pliers to open and slide the
clamp down the hose. Disconnect the
drain hose from the washer and drain
any water in the hose into a bucket.
6.Pull the washer away from wall so it
can be tipped on its back.
7.Protect the floor with a large piece of
cardboard cut from the pedestal carton.
Lay the washer on its back (make sure
that the power supply cord is not under
the washer) so that the cardboard is
under the entire lower back edge of the
washer (see Figure 1). An additional
small amount of water will drain out of
the washer when it is tipped back. Go
to “Installing the Pedestal”.
Uninstalling your washer:
Excessive Weight Hazard
Use two or more people to move
and uninstall dryer.
Failure to do so can result in back
or other injury.
WARNING
Uninstalling your electric
dryer:
1.Unplug the power supply cord.
2.Pull the dryer away from the wall
enough to loosen the vent clamp. Loosen
the clamp and carefully remove the
exhaust vent from the dryer exhaust outlet.
3.Pull the dryer away from wall so that it
can be tipped on its back.
4.Protect the floor with a large piece of
cardboard cut from the pedestal carton.
Lay the dryer on its back (make sure
that the power supply cord is not under
the dryer) so that the cardboard is under
the entire lower back edge of the dryer
(see Figure 1). Go to “Installing the
Pedestal”.
Excessive Weight Hazard
Use two or more people to move
and uninstall dryer.
Failure to do so can result in back
or other injury.
WARNING
Uninstalling your gas dryer:
1.Unplug the power supply cord.
2.Turn off the gas supply.
3.Pull the dryer away from the wall
enough to loosen the vent clamp.
Loosen the clamp and carefully remove
the exhaust vent from the dryer exhaust
outlet.
4.Disconnect the flexible gas supply
line from the dryer. Put a piece of tape
over the open ends of the gas line
connection fittings.
5.Pull the dryer away from wall so that
it can be tipped on its back.
6.Protect the floor with a large piece of
cardboard cut from the pedestal carton.
Lay the dryer on its back (make sure
that the power supply cord is not under
the dryer) so that the cardboard is under
the entire lower back edge of the dryer
(see Figure 1). Go to “Installing the
Pedestal”.
You can be killed or seriously
injured if you don’t follow
instructions.
DANGER
Your safety and the safety of
others are very important.
We have provided many important
safety messages in this manual and
on your appliance. Always read and
obey all safety messages.
All safety messages will tell you
what the potential hazard is, tell you
how to reduce the chance of injury,
and tell you what can happen if the
instructions are not followed.
You can be killed or seriously
injured if you don’t immediatel
y
follow instructions.
WARNING
This is the safety alert
symbol.
This symbol alerts you to
potential hazards that can kill or hurt
you and others.
All safety messages will follow the
safety alert symbol and either the
word “DANGER” or “WARNING”.
These words mean:
Tools required:
• Utility knife
• Phillips screwdriver (drawer removal)
• 1/4" (6.5 mm) hex head ratchet or open-end wrench
(leveling legs)
• 5/16" (8 mm) hex head ratchet (sheet metal screws)
• Level
• 9/16" (14.3 mm) open-end wrench (leveling leg
locknuts)
• pliers or slip-joint pliers (for drain and inlet hoses)
2
cardboard
12"
(30.5 cm)
15"
(38.1 cm)
Figure 1
Note: If dryer and pedestal assembly is
located in a garage, 6" (15.2 cm) must
be added under pedestal so that dryer
is 18" (45.7 cm) above garage floor.
Loading ...
Loading ...
Loading ...