Loading ...
Loading ...
Loading ...
EN7
MATERIALS SUPPLIED
Remove all the components from the packets. Check that all the components are included.
• Hood assembled with motor and lamps installed.
• Flue support bracket
• Assembly template
• Filter/s
• Instruction manual
• 2 - washers
• 6 - plugs 8 x 40 mm
• 6 - screws 5 x 45 mm
• 2 - screws 2.9 x 6.5 mm
• 2 - screws 3 x 9 mm
INSTALLATION PRELIMINARY ASSEMBLY INSTRUCTIONS
The hood is designed for use in “Extractor version” or in “Filter version”.
Extractor Version
Fumes are extracted and expelled to the outside through an exhaust pipe (not supplied) xed to the hood exhaust pipe
connector (Fig.d, Fig.e).
Depending on the exhaust pipe purchased, provide for suitable xing to the exhaust pipe connector.
Important: If already installed, remove the carbon lter/s.
Filter Version
Air is ltered through the carbon lter/s and recycled into the surrounding environment.
Important: check that air recirculation is facilitated (to this end, carefully follow the instructions given in the installation
handbook).
Important! If the hood does not have a carbon lter/s, it/they must be ordered and tted before use.
Preliminary information for installing the hood:
Expansion plugs are provided to secure the hood to most types of ceilings. However, a qualied technician is needed to
make sure that the plugs are suitable for your ceiling. The wall/ceiling must be strong enough to take the weight of the
hood. Remove the grease lters.
Pre-assembly of the electrical connection box:
(a.) remove the screws and washers on the extractor unit and remove the adhesive tape xing the box to the extractor unit,
(b.) position the electrical connection box above the extractor unit,
(c.) secure with 2 Ø 3.5 x 9.5 screws and 2 Ø 14 x 12 washers (previously removed).
1. Using a pencil, draw the centre line on the wall up to the ceiling (Fig.1).
2. If necessary, cut the drilling template according to the width of the hood.
3. Apply the drilling template to the wall: the vertical centre line printed on the drilling template must match the centre
line drawn on the wall and, depending on the height of the hood, the lower horizontal edge of the drilling template
must match the lower edge of the hood.
4. Drill as shown on the template, insert the wall plugs and screw in the top 2 screws, leaving a space of approx. 1 cm
between the screw head and the wall.
Note: Drill all the holes indicated on the template: the top 2 holes are for hanging the hood and the bottom holes are
for xing it securely to the wall.
5. Fit the ue support bracket “G” (Fig.1) to the wall and against the ceiling. Use the support bracket as drilling template
(if present, the small slot on the support must match the line drawn on the wall) and mark 2 holes with the pencil,
drill the holes and nally insert 2 plugs.
6. Fix the ue support bracket to the wall with 2 screws.
7. Remove the drilling template from the wall and hang the hood on the 2 top screws (Fig.1).
8. Screw in the bottom screws (and washers!) to x the hood securely in place (COMPULSORY!!). After checking the
alignment of the hood, TIGHTEN ALL THE SCREWS - top and bottom.
Note: the bottom xing points are visible upon removal of the grease lters.
9. Connect an exhaust pipe to the exhaust pipe connector located above the extraction motor unit. For extractor
operation, connect the other end of the exhaust pipe to the home discharge device. For lter operation, x the deector
F to the ue support bracket G and connect the other end of the exhaust pipe to the deector collar F (Fig.1).
10. Make all necessary electrical connections.
11. Fit the ues over the extractor unit, engaging them in their seat above the hood.
12. Slide the top section of the ue upwards and secure it with 2 screws (11a) to the ue support bracket “G” (11b).
Ret the grease lters and check for correct hood operation.
Loading ...
Loading ...
Loading ...