User Manual KitchenAid KESA907PBL cooking

KitchenAid KESA907PBL cooking - Use Manual - Use Guide PDF.
Documents: Go to donwload!
User Manual
  • Owner's manual - (English)
Other Documents
  • Installation Instructions - (English)



TABLE OF CONTENTS

RANGE SAFETY ..2 INSTALLATION REQUIREMENTS 3 Tools and Parts .3 Location Requirements .3 Electrical Requirements - U.S.A. Only ..6 Electrical Requirements - Canada Only 7 Countertop Preparation (for Slide-in Ranges Only) 7 INSTALLATION INSTRUCTIONS ..8 Unpack Range 8 Adjust Leveling Legs ..8 Install Anti-Tip Bracket ..8 Optional Rear Spacer Cover (for Slide-in Ranges Only) ..9 Electrical Connection - U.S.A. Only 9 Verify Anti-Tip Bracket Location 13 Level Range ..13 Complete Installation ..14 Moving the Range .14 ANTI-TIP BRACKET TEMPLATE 23

TABLE DES MATIÈRES

SÉCURITÉ DE LA CUISINIÈRE 15 EXIGENCES D'INSTALLATION 16 Outillage et pièces .16 Exigences d'emplacement 16 Spécifications électriques .19 Préparation du plan de travail (pour cuisinières encastrées uniquement) 19 INSTRUCTIONS D'INSTALLATION 19 Déballage de la cuisinière .19 Ajuster les pieds de nivellement .20 Installation de la bride antibasculement 20 Garniture d’obturation arrière facultative (pour cuisinières encastrées uniquement) 21 Vérification de l'emplacement de la bride antibasculement 21 Mise à niveau de la cuisinière .21 Achever l’installation 22 Déplacement de la cuisinière ..22 GABARIT POUR LA BRIDE ANTIBASCULEMENT ..23

RANGE SAFETY

You can be killed or seriously injured if you don't immediately

You can be killed or seriously injured if you don't follow

All safety messages will tell you what the potential hazard is. tell you how to reduce the chance of injury. and tell you what can happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These words mean:

DANGER

WARNING

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket. if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed here.

Tools needed

Parts supplied Check that all parts are included.

Anti-tip bracket must be securely mounted to subfloor.

Thickness of flooring may require longer screws to anchor bracket to sub-floor. Longer screws are available from your local hardware store.

Parts needed If using a power supply cord:

A UL listed power supply cord kit marked for use with ranges.

The cord should be rated at 250 volts minimum. 40 amps or 50 amps that is marked for use with nominal 1³⁄₈" (3.5 cm) diameter connection opening and must end in ring terminals or open-end spade terminals with upturned ends.

A UL listed strain relief.

Check local codes. Check existing electrical supply. See “Electrical Requirements” section.

It is recommended that all electrical connections should be made by a licensed. qualified electrical installer.

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the oven door on the right-hand side oven door trim.

The range should be located for convenient use in the kitchen.

To eliminate the risk of burns or fire by reaching over heated surface units. cabinet storage space located above the surface units should be avoided. If cabinet storage is to be provided. the risk can be reduced by installing a range hood that projects horizontally a minimum of 5" (12.7 cm) beyond the bottom of the cabinets.

Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

The floor anti-tip bracket must be installed. To install the anti tip bracket shipped with the range. see “Install Anti-Tip Bracket” section.

Grounded electrical supply is required. See “Electrical Requirements” section.

IMPORTANT: To avoid damage to your cabinets. check with your builder or cabinet supplier to make sure that the materials used will not discolor. delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).

Mobile Home - Additional Installation Requirements The installation of this range must conform to the Manufactured Home Construction and Safety Standard. Title 24 CFR. Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety. Title 24. HUD Part 280). When such standard is not applicable. the Standard for Manufactured Home Installations.

ANSI A225.1/NFPA 501A or follow local codes.

In Canada. the installation of this range must conform with the current standards CAN/CSA-A240-latest edition. or local codes.

Mobile home installations require:

When this range is installed in a mobile home. it must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

Four-wire power supply cord or cable must be used in a mobile home installation. The appliance wiring will need to be revised. See “Electrical Connection” section.

Tape measure

Flat-blade screwdriver

Level

Hammer

Hand or electric drill

Wrench or pliers

Marker or pencil

Masking tape

¼" nut driver

⁵⁄₁₆" nut driver

¹⁄₈" (3.2 mm) drill bit (for wood floors)

³⁄₁₆" (4.8 mm) carbide-tipped masonry drill bit (for concrete/ceramic floors)

A. Anti-tip bracket B. Plastic anchors (2) C. #10 x ¹⁄₂" screws (2) D. Rear spacer cover for slide-in models (supplied on some models)*

+To order. contact your dealer or refer to the “Assistance or Service” section of the Use and Care Guide. Ask for Part Number 9757784WH (White). 9757784BT (Biscuit). 9757784BL (Black). 9757784MT (Meteorite) or 9757784SS (Stainless Steel).

Electrical Requirements - U.S.A. Only

If codes permit and a separate ground wire is used. it is recommended that a qualified electrical installer determine that the ground path is adequate and wire gauge is in accordance with local codes.

Do not use an extension cord.

Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code. ANSI/ NFPA 70-latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from: National Fire Protection Association One Batterymarch Park Quincy. MA 02269 WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service technician if you are in doubt as to whether the appliance is properly grounded. Do not modify the power supply cord plug. If it will not fit the outlet. have a proper outlet installed by a qualified electrician.

Electrical Connection To properly install your range. you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

Range must be connected to the proper electrical voltage and frequency as specified on the model/serial number rating plate. The model/serial number rating plate is located on the oven frame behind the storage drawer panel. Refer to the figures in the “Product Dimensions” section of the “Location Requirements” section.

This range is manufactured with the neutral terminal connected to the cabinet. Use a 3-wire UL listed. 40- or 50 amp power supply cord (pigtail) (see Range Rating chart below). If local codes do not permit ground through the neutral. use a 4-wire power supply cord rated at 250 volts.

40 or 50 amps and investigated for use with ranges.

+The NEC calculated load is less than the total connected load listed on the model/serial rating plate.

+*If connecting to a 50-amp circuit. use a 50-amp rated cord with kit. For 50-amp rated cord kits. use kits that specify use with a nominal 1³⁄₈" (34.93 mm) diameter connection opening.

A time-delay fuse or circuit breaker is recommended.

The range can be connected directly to the fused disconnect (or circuit breaker box) through flexible or nonmetallic sheathed. copper or aluminum cable. See “Electrical Connection.”

Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack in the line so that the range can be moved if servicing is ever necessary.

A UL listed conduit connector must be provided at each end of the power supply cable (at the range and at the junction box).

Wire sizes and connections must conform with the rating of the range (40 amps).

The wiring diagram is located on the underside of the storage drawer or below the warming drawer in a clear plastic bag.

If connecting to a 4-wire system: This range is manufactured with the ground connected to the cabinet. The ground must be revised so the green ground wire of the 4-wire power supply cord is connected to the cabinet. See “Electrical Connection.” Grounding through the neutral conductor is prohibited for new branch-circuit installations (1996 NEC); mobile homes; and recreational vehicles. or an area where local codes prohibit grounding through the neutral conductor.

When a 4-wire receptacle of NEMA Type 14-50R is used. a matching UL listed. 4-wire. 250-volt. 40-amp. range power supply cord (pigtail) must be used. This cord contains 4 copper conductors with ring terminals or open-end spade terminals with upturned ends. terminating in a NEMA Type 14-50R plug on the supply end.

The fourth (grounding) conductor must be identified by a green or green/yellow cover and the neutral conductor by a white cover.

Cord should be Type SRD or SRDT with a UL listed strain relief and be at least 4 ft (1.22 m) long.

The minimum conductor sized for the copper 4-wire power cord are: 40-amp circuit 2 No.-8 conductors 1 No.-10 white neutral 1 No.-8 green grounding

If connecting to a 3-wire system: Local codes may permit the use of a UL listed. 3-wire.

250-volt. 40 or 50-amp range power supply cord (pigtail). This cord contains 3 copper conductors with ring terminals or open end spade terminals with upturned ends. terminating in a NEMA Type 10-50P plug on the supply end. Connectors on the appliance end must be provided at the point the power supply cord enters the appliance. This uses a 3-wire receptacle of NEMA Type 10-50R.

Range Rating* Specified Rating of Power Supply Cord Kit and Circuit Protection

120/240 Volts 120/208 Volts Amps

8.8 - 16.5 KW 16.6 - 22.5 KW 7.8 - 12.5 KW 12.6 - 18.5 KW 40 or 50**

4-wire receptacle (14-50R)

3-wire receptacle (10-50R)

Electrical Requirements - Canada Only

If codes permit and a separate ground wire is used. it is recommended that a qualified electrical installer determine that the ground path is adequate and wire gauge are in accordance with local codes.

Be sure that the electrical connection and wire size are adequate and in conformance with CSA Standard C22.1. Canadian Electrical Code. Part 1 - latest edition. and all local codes and ordinances.

A copy of the above code standards can be obtained from:

Canadian Standards Association 178 Rexdale Blvd.

Toronto. ON M9W 1R3 CANADA.

Check with a qualified electrical installer if you are not sure the range is properly grounded.

+The NEC calculated load is less than the total connected load listed on the model/serial rating plate.

+*If connecting to a 50-amp circuit. use a 50-amp rated cord with kit. For 50-amp rated cord kits. use kits that specify use with a nominal 1³⁄₈" (34.93 mm) diameter connection opening.

A time-delay fuse or circuit breaker is recommended.

This range is equipped with a CSA International Certified Power Cord intended to be plugged into a standard 14-50R wall receptacle. Be sure the wall receptacle is within reach of range’s final location.

Do not use an extension cord.

Countertop Preparation (for Slide-in Ranges Only)

The cooktop sides of the slide-in range fit over the cutout edge of your countertop.

If you have a square finish (flat) countertop and the opening width is 30" (76.2 cm). no countertop preparation is required.

Formed front-edged countertops must have molded edge shaved flat ³⁄₈" (1.0 cm) from each front corner of opening.

Tile countertops may need trim cut back ³⁄₈" (1.0 cm) from each front corner and/or rounded edge flattened.

If countertop opening width is greater than 30" (76.2 cm). adjust the ³⁄₈" (1.0 cm) dimension.

Countertop must be level. Place level on countertop. first side to side. then front to back. If countertop is not level. range will not be level. Range must be level for satisfactory baking conditions.

Range Rating* Specified Rating of Power Supply Cord Kit and Circuit Protection

120/240 Volts 120/208 Volts Amps

8.8 - 16.5 KW 16.6 - 22.5 KW 7.8 - 12.5 KW 12.6 - 18.5 KW 40 or 50**

WARNING

Electrical Shock Hazard

Electrically ground range.

Failure to do so can result in death. fire. or electrical shock.

(76.2 cm)

30 ¾" (78.1 cm)

³⁄₈" (1.0 cm)

INSTALLATION INSTRUCTIONS

Unpack Range

Remove shipping materials. tape and protective film from the range. Keep cardboard bottom under range. Remove oven racks and parts package from inside oven.

To place range on its back. take 4 cardboard corners from the carton. Stack one cardboard corner on top of another.

Repeat with the other 2 corners. Place them lengthwise on the floor behind the range to support the range when it is laid on its back. Using 2 or more people. firmly grasp the range and gently lay it on its back on the cardboard corners.

Pull cardboard bottom firmly to remove.

Adjust Leveling Legs

If range height adjustment is necessary. use a wrench or pliers to loosen the 4 leveling legs.

This may be done with the range on its back or with the range supported on 2 legs after the range has been placed back to a standing position.

NOTE: To place range back up into a standing position. put a sheet of cardboard or hardboard in front of range. Using 2 or more people. stand range back up onto the cardboard or hardboard.

Adjust the leveling legs to the correct height. Leveling legs can be loosened to add up to a maximum of 1" (2.5 cm). A minimum of ³⁄₁₆" (5 mm) is needed to engage the anti-tip bracket.

NOTE: If height adjustment is made when range is standing. tilt the range back to adjust the front legs. then tilt forward to adjust the rear legs.

When the range is at the correct height. check that there is adequate clearance under the range for the anti-tip bracket.

Before sliding range into its final position. check that the anti tip bracket will slide under the range and onto the rear leveling leg prior to anti-tip bracket installation.

Install Anti-Tip Bracket

Contact a qualified floor covering installer for the best procedure for drilling mounting holes through your type of floor covering.

Before moving range. slide range onto shipping base. cardboard or hardboard.

Remove template from the anti-tip bracket kit (found inside the oven cavity) or from the back of this manual.

Place template on the floor in cabinet opening so that the left edge is against cabinet and top edge is against rear wall. molding or cabinet.

Tape template into place.

If countertop is not flush with cabinet opening edge. align template with overhang.

If cabinet opening is wider than that specified in the “Location Requirements” section. adjust template so range will be centered in cabinet opening.

To mount anti-tip bracket to wood floor. drill two ¹⁄₈" (3.2 mm) holes at the positions marked on the bracket template.

Remove template from floor.

To mount anti-tip bracket to concrete or ceramic floor. use a ³⁄₁₆" (4.8 mm) masonry drill bit to drill 2 holes at the positions marked on the bracket template. Remove template from floor.

Tap plastic anchors into holes with a hammer.

WARNING

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket. if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

Align anti-tip bracket holes with holes in floor. Fasten anti-tip bracket with screws provided.

Depending on the thickness of your flooring. longer screws may be necessary to anchor the bracket to the subfloor.

Longer screws are available from your local hardware store.

Move range close enough to opening to allow for electrical connections to be made. Remove shipping base. cardboard or hardboard from under range.

Make electrical connections as described in the “Electrical Connection” section.

10. Move range into its final location making sure rear leveling leg slides into anti-tip bracket.

11. If installing the range in a mobile home. you must secure the range to the floor. Any method of securing the range is adequate as long as it conforms to the standards in the “Location Requirements” section.

12. Continue installing your range using the following installation instructions.

Optional Rear Spacer Cover (for Slide-in Ranges Only)

If you are installing a slide-in range into an existing freestanding range opening. you may use the rear spacer cover to fill in the opening at rear of range. To order. see the “Assistance or Service” section of the Use and Care Guide or contact the dealer from whom you purchased the range.

Using the screws provided with the kit. attach the rear spacer cover to the sides of the range.

Electrical Connection - U.S.A. Only

Power Supply Cord

Direct Wire

Disconnect power.

Remove the terminal block cover screws located on the back of the range. Pull cover down and toward you to remove cover.

A. Hold-down screws B. Terminal block cover

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use a new 40 amp power supply cord.

Plug into a grounded outlet.

Failure to follow these instructions can result in death. fire. or electrical shock.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Use 8 gauge copper or 6 gauge aluminum wire.

Electrically ground range.

Failure to follow these instructions can result in death. fire. or electrical shock.

Add strain relief.

Style 1: Power supply cord strain relief

Remove the knockout for the 40-amp supply cord.

Assemble a UL listed strain relief in the opening.

Feed the power supply cord behind the black horizontal cross brace and through the strain relief. allowing enough slack to easily attach the wiring to the terminal block.

Tighten strain relief screw against the power supply cord.

Style 2: Direct wire strain relief

Remove the knockout as needed for the flexible conduit connection.

Assemble a UL listed conduit connector in the opening.

Feed the flexible conduit behind the black horizontal cross brace and through the strain relief. allowing enough slack to easily attach the wiring to the terminal block.

Tighten strain relief screw against the flexible conduit.

Complete installation following instructions for your type of electrical connection: 4-wire (recommended)

3-wire (if 4-wire is not available)

A. UL listed strain relief

A. Black horizontal cross brace B. Power supply cord

A. Removable retaining nut B. Strain relief

A. Black horizontal cross brace B. Flexible conduit

Electrical Connection Options

4-wire connection: Power Supply Cord

Use this method for:

New branch-circuit installations (1996 NEC)

Mobile homes

Recreational vehicles

In an area where local codes prohibit grounding through the neutral.

Remove the ground-link screw from the range frame. Save the ground link screw and cup washer. Bend the ground-link away from the range so that it does not contact the range.

Connect the green ground wire from the power supply cord to the range using the ground-link screw. The ground wire must be attached first and must not contact any other terminal.

Use a ¼" nut driver and remove the hex washer head screws from the terminal blocks.

Connect the neutral (center) wire to the center terminal connector using one of the hex washer head screws.

Securely tighten screw.

Connect the other 2 wires (lines 1 and 2) to the outer aluminum terminal blocks.

Securely tighten screws.

Tighten strain relief screws.

Replace terminal block cover with screw.

3-wire connection: Power Supply Cord

Use this method only if local codes permit connecting cabinet ground conductor to neutral wire of power supply cord.

Use a ¼" nut driver and remove the hex washer head screws from the aluminum terminal blocks.

Connect the neutral (center) wire to the center terminal connector using one of the hex washer head screws.

Securely tighten screw for proper electrical connection.

Connect the other 2 wires (lines 1 and 2) to the outer terminal screws on the terminal block.

Tighten strain relief screws.

Replace terminal block cover.

If your home has: And you will be connecting to: Go to Section:

4-wire receptacle (NEMA type 14-50R) A UL listed.

250-volt minimum.

40-amp. range power supply cord

4-wire connection: Power supply cord

4-wire direct A fused disconnect or circuit breaker box

4-wire connection: Direct wire

3-wire receptacle (NEMA type 10-50R) A UL listed.

250-volt minimum.

40-amp. range power supply cord

3-wire connection: Power supply cord

3-wire direct A fused disconnect or circuit breaker box

3-wire connection: Direct wire

A. Ground-link screw B. Cup washer C. Ground-link bent away from range

(12.7 cm)

(7.6 cm)

(2.5 cm)

A. Line 1 B. Green ground wire C. Ground-link screw D. Hex washer head screw E. Silver-colored terminal block screw

F. Ground-link G. Neutral (center) wire H. Line 2 I. UL listed strain relief and 40-amp range power supply cord

A. Line 1 B. Ground-link C. Hex washer head screw D. Silver-colored terminal block screw

E. Neutral (center) wire F. Line 2 G. UL listed strain relief and 40-amp range power supply cord

Direct Wire Installation: Copper or Aluminum Wire

This range may be connected directly to the fuse disconnect or circuit breaker box. Depending on your electrical supply. make the required 3-wire or 4-wire connection.

Strip outer covering back 3" (7.6 cm) to expose wires. Strip the insulation back 1" (2.5 cm) from the end of each wire.

Allow enough slack in the wire to easily attach the wiring terminal block.

Complete electrical connection according to your type of electrical supply (4-wire or 3-wire connection).

4-wire Connection: Direct Wire

Use this method for:

New branch-circuit installations (1996 NEC)

Mobile homes

Recreational vehicles

In an area where local codes prohibit grounding through the neutral

Remove the ground-link screw from the range frame. Save the ground-link screw and cup washer. Bend the ground-link away from the range so that it does not contact the range.

Connect the bare ground wire to the range using the ground link screw and cup washer. The ground wire must be attached first and must not contact any other terminal.

Loosen (do not remove) the hex washer head screw and insert the neutral (white) wire under the screw clamp at the bottom of the center position terminal connector.

Insert the other 2 wires (lines 1 and 2) under the other 2 screw clamps.

Securely tighten the hex washer head screws to 35 lbs-in. (4.0 N-m) minimum torque to make proper electrical connection.

Tighten the locking ring of the conduit connector.

Replace the terminal block cover.

A. Ground-link screw B. Cup washer C. Ground-link bent away from range

(7.6 cm)

(2.5 cm)

A. Bare wire from power supply cable B. Line 1 C. Hex washer head screw D. Silver-colored terminal block screw

E. Line 2 F. Neutral (white) wire G. UL listed conduit connector and power supply cable

A. Insert wire under screw clamp.

B. Hex washer head screw

3-wire connection: Direct Wire

Use this method only if local codes permit connecting ground conductor to neutral supply wire.

Loosen (do not remove) the hex washer head screws and insert the neutral (white) wire under the screw clamp at the bottom of the center position terminal connector.

Insert the other 2 wires (lines 1 and 2) under the other 2 screw clamps.

Securely tighten the hex washer head screws to 35 lbs-in. (4.0 N-m) minimum torque to make a proper electrical connection.

Tighten the locking ring of the conduit connector.

Replace the terminal block cover.

Verify Anti-Tip Bracket Location

Pull drawer open to first stop position. Lift front of drawer to clear white wheels in drawer guides. Remove drawer and set it aside on a protected surface.

Making sure the anti-tip bracket is installed:

Look for the anti-tip bracket securely attached to floor.

Slide range back so rear range foot is under anti-tip bracket.

If installing the range in a mobile home. you must secure the range to the floor. Any method of securing the range is adequate as long as it conforms to the standards in the “Location Requirements” section.

Level Range

Place rack in oven. Place level on rack and check levelness of range. first side to side; then front to back.

If range is not level. pull range forward until rear leveling leg is removed from the anti-tip bracket.

On Ranges Equipped with Storage Drawers:

Use ³⁄₈" drive ratchet and channel lock pliers to adjust leveling legs up or down until range is level. Push range back into position. Check that rear leveling leg is engaged in anti-tip bracket.

On Ranges Equipped with Warming Drawers:

Use channel lock pliers to adjust leveling legs up or down until range is level. Push range back into position. Check that rear leveling leg is engaged in anti-tip bracket.

NOTE: Range must be level for satisfactory baking conditions.

Replace the storage drawer (and warming drawer on some models).

A. Line 1 B. Ground-link C. Hex washer head screw D. Silver-colored terminal block screw

E. Neutral (white) wire F. Line 2 G. UL listed conduit connector and power supply cable

A. Insert wire under screw clamp.

B. Hex washer head screw

Complete Installation

Check that all parts are now installed. If there is an extra part. go back through the steps to see which step was skipped.

Check that you have all of your tools.

Dispose of/recycle all packaging materials.

Check that the range is level. See “Level Range.”

Use a mild solution of liquid household cleaner and warm water to remove waxy residue caused by protective shipping material. Dry thoroughly with a soft cloth. For more information. read the “Range Care” section of the Use and Care Guide.

Read “Range Use” in the range Use and Care Guide.

Plug power cord into appropriate outlet. Turn power on.

Turn on surface burners and oven. See the Use and Care Guide for specific instruction on range operation.

If range does not operate. check the following:

Household fuse is intact and tight; or circuit breaker has not tripped.

Range is plugged into an outlet.

Electrical supply is connected.

See “Troubleshooting” in the Use and Care Guide.

When the range has been on for 5 minutes. check for heat. If range is cold. turn off the range and contact a qualified technician.

Moving the Range

When moving range. slide range onto cardboard or hardboard to avoid damaging the floor covering.

If removing the range is necessary for cleaning or maintenance:

For power supply cord-connected ranges:

Unplug the power supply cord.

Slide range forward to complete cleaning or maintenance.

Check that anti-tip bracket is installed:

Look for the anti-tip bracket securely attached to floor.

Slide range back so rear range foot is under anti-tip bracket.

Check that range is level.

For direct-wired ranges:

Disconnect power.

Disconnect wiring.

Slide range forward to complete cleaning or maintenance.

Check that anti-tip bracket is installed:

Look for the anti-tip bracket securely attached to floor.

Slide range back so rear range foot is under anti-tip bracket.

Check that range is level.

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Connect anti-tip bracket to rear range foot.

Reconnect the anti-tip bracket. if the range is moved.

Failure to follow these instructions can result in death or serious burns to children and adults.

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.



Newest Added: MEW9630AB UXT4030AAQ GU2300XTVB MDB8959SAS GU3600XTVY

KitchenAid KESA907PBL | File type: PDF | Filename: ykesv908ps.pdf | Size: 492.7 KB | Language: English | Other documents: 1 files.

Download User Manual

Contact us

KitchenAid in United States

1 (800) 422-1230, 1 (800) 541-6390 Hours of Operation Mon - Fri: 8 a.m. - 8 p.m. EST