Loading ...
JENN-AIR
®
DETAILED PLANNING DIMENSIONS
Product dimension, cutout and installation specifications are provided for planning purposes only. Before installing
any product, be sure to verify cutout dimensions and electrical/gas connections as actual product dimensions may vary.
JENN-AIR
®
DETAILED PLANNING DIMENSIONS
2 of 4
7778BdZw613
E*
L
N
P
O
F
D
e
A
BB
M
v
v
C
J**
H
G
M
Side
Cabinet
C
K
I
E*
L
N
P
O
F
D
e
A
BB
M
v
v
C
J**
H
G
M
Side
Cabinet
C
K
I
E*
L
N
P
O
F
D
e
A
BB
M
v
v
C
J**
H
G
M
Side
Cabinet
C
K
I
36" JX3™ GAS DOWNDRAFT COOKTOP
JGD3536B – 36" x 18
3
⁄8" x 21
1
⁄2"
MODEL # JGD3536B
in cm
A
Width of combustible area above cooking
surface (min.)
36 91.4
B
Width from cooktop to fixed wall or other
combustible material (min.)
6 15.2
C
Width to center of vent opening option 17
1
⁄2 44.4
D
Width to outer edge of outlet 10 25.4
E*
Height to bottom of uncovered wood or metal
cabinet above cooking surface (min.)
30 76.2
F
Height to bottom of uncovered wood or metal
cabinet (min.)
18 45.7
G
Height to center of vent opening option 16 40.6
H
Height to top edge of outlet (min.) 12 30.5
I
Height to top of gas installation area 6 15.2
J**
Depth to center of vent opening option 17
1
⁄8 43.5
K
Depth of gas installation area 6 15.2
L
Depth of upper cabinet (recommended) 13 33.0
M
Depth from cutout to wall (min.) 2 5.1
N
Width of cutout 34
3
⁄4 88.3
O
Depth of cutout 20 50.6
P
Depth from cutout to front of countertop 2
1
⁄8 5.4
e
Recommended electrical access location
g
Recommended gas supply line location
v
Recommended venting location –
see pages 3-4 for ducting information
* Dimension can be reduced by 6" (15.2 cm) when bottom of wood or metal
cabinet is covered by not less than
1
⁄4" (0.6 cm) flame retardant millboard
covered with not less than No. 28 MSG sheet metal, 0.015" (0.4 mm) stainless
steel, 0.024" (0.6 mm) aluminum or 0.020" (0.5 mm) copper.
**Based on installation in a 24" deep (61.0 cm) base cabinet.
OPENING/CLEARANCE DIMENSIONS
FRONT VIEW
SIDE VIEW TOP VIEW
GAS REQUIREMENTS
Natural Gas
This cooktop is factory-set for use with natural gas.
LP Gas Conversion
Conversion must be done by a qualified service technician. To convert to LP gas, use
the LP gas conversion kit provided with the cooktop.
ELECTRICAL REQUIREMENTS
120 volt, 60 Hz, AC only, 15-amp fused, electrical circuit is required. A time-delay
fuse or dedicated circuit is recommended.
VENTING REQUIREMENTS
This cooktop must be exhausted outdoors unless using the duct-free filter kit
(JDA7000WX). Refer to kit instructions for further information.
LOCATION REQUIREMENTS
• To ensure cooktop base clearance, cabinet side walls need to be wider than the cutout.
• A minimum clearance of 2" (5.1 cm) is recommended between the blower motor and
cabinet for proper cooling. A 6" (15.2 cm) clearance is recommended for servicing access.
• An under counter built-in oven cannot be installed under this cooktop.
Loading ...
Loading ...