Loading ...
Loading ...
Trimming facial hair (nose hair, ear hair
and eyebrows)
1 To remove the comb, press the hair length
selector (1) and slide the comb upwards
(2) (Fig. 16).
2 Press the release button (1) and pull the
trimming attachment off the appliance
(2). (Fig. 17)
3 Put the nose/ear/eyebrow attachment on the
appliance (Fig. 20).
Trimming nose hair
1 Make sure your nostrils are clean.
2 Switch on the appliance and insert the
tip of the attachment into one of your
nostrils. (Fig. 21)
Do not insert the tip more than 0.5cm into
your nostril.
3
Slowly move the tip in and out and turn it round
at the same time to remove unwanted hair.
To reduce the tickling effect, make sure that the
side of the tip is rmly pressed against the skin.
Trimming ear hair
1 Clean the outer ear channel. Make sure it is
free from wax.
2 Switch on the appliance and move the tip
softly round the ear to remove hairs that
stick out beyond the rim of the ear. (Fig. 22)
3 Carefully insert the tip into the outer ear
channel. (Fig. 23)
Do not insert the tip more than 0.5cm into the
ear channel, as this could damage the eardrum.
Trimming eyebrows
Use the tip to cut individual eyebrow hairs.
Do not use the appliance to dene or trim the
entire eyebrow.
Never try to trim your eyelashes.Never come
too close to your eyes!
1 Place the tip of the attachment on the upper
edge of the eyebrow.
2 Move it along the edge of the eyebrow from
the base of the nose towards the outer tip of
the eyebrow. (Fig. 24)
Shaving
Shaving with the micro shaver
attachment
Before you use the micro shaver attachment,
always check it for damage or wear. If the foil
or cutter is damaged or worn, do not use the
attachment as injury may occur. Replace the foil
or the cutter before you use the attachment again.
1 Put the micro shaver attachment on the
appliance. (Fig. 25)
2 Gently press the micro shaver attachment
onto the skin.
Do not press too hard.
3 Shave along contoured edges to remove any
stubble and to create a smooth, well-dened
beard line.
Cleaning
Do not clean the appliance with water or a
moist cloth.
Never use scouring pads, abrasive cleaning agents
or aggressive liquids such as alcohol, petrol or
acetone to clean the appliance.
1 Make sure the appliance is switched off and
disconnected from the mains.
2 Remove the comb and/or attachment.
3 Separate the top part of the micro shaver
attachment from its body (Fig. 26).
Avoid touching the shaving foil, as it is very
delicate.
Do not clean the foil with the brush, as this can
cause damage.
4 Blow and/or shake out any hair that has
accumulated in the attachment.
5 Clean the outside and inside of the
attachment with the brush supplied. (Fig. 27)
6 Place the attachment back onto the appliance.
Replacement
Only replace worn or damaged attachments or
combs with original Philips replacement
attachments or combs, that are available from your
dealer or an authorised Philips service centre.
If you have any difculties obtaining replacement
attachments or combs for your appliance, contact
the Philips Consumer Care Centre in your country
or consult the worldwide guarantee leaet.
Environment
- Do not throw away the appliance with the
normal household waste at the end of its life,
but hand it in at an ofcial collection point for
recycling. By doing this, you help to preserve
the environment (Fig. 28).
- The built-in rechargeable battery contains
substances that may pollute the environment.
Always remove the battery before you
discard and hand in the appliance at an ofcial
collection point. Dispose of the battery at an
ofcial collection point for batteries. If you have
trouble removing the battery, you can also take
the appliance to a Philips service centre. The
staff of this centre will remove the battery for
you and will dispose of it in an environmentally
safe way. (Fig. 29)
Disposal of the battery
1 Remove the adapter from the wall socket and
pull the appliance plug out of the appliance.
2 Let the appliance run until the motor stops.
3 Insert a screwdriver in the groove next to
the shaft at the top of the appliance.Turn
the screwdriver to separate the two housing
halves. (Fig. 30)
4 Lift the battery out of the housing with a
screwdriver. Twist the connecting wires until
they break (Fig. 31).
Do not connect the appliance to the mains again
you have removed the battery.
Guarantee & service
If you need service or information or if you have
a problem, please visit the Philips website at
www.philips.com or contact the Philips Consumer
Care Centre in your country (you nd its phone
number in the worldwide guarantee leaet).
If there is no Consumer Care Centre in your
country, go to your local Philips dealer.