Loading ...
Loading ...
Loading ...
5
ENGLISH
Wall mount
screw
→ If the screw cannot be assembled in the designated
location inevitably, it can be assembled by rearranging
to the closest location. But, do not change 2 or more
locations from the designated spot.
→ Assemble the wall mount screw on 2 left and 2 right
location on the top part and 1 left and 1 right location on
the bottom part.
→ At this time, use a + driver (manual or motorized) or 8 mm
wrench to tighten the screw so that the wall, wall bracket
and screw are completely pressed against one another.
When mounting to wooden studs
406 mm
drywall
drywall
wood stud
76 mm
Wall mount
screw
a. Locate and mark the centers of the wall studs using a stud finder.
b. After aligning the wall bracket on the wall where the center of the wood stud is marked, mark the location of the screws and then
remove the wall bracket.
c. Use a level to make sure your screw marks are level.
d. Use the Ø 4 mm drill bit for wood to drill holes with the depth of 76 mm or above where the wall mount screw location is marked on the wall.
e. Clean the drilled hole.
f. Tighten the wall mount screws for the wall bracket on the drilled hole.
→ At this time, tighten the screw so that the wall, wall bracket and the wall mount screw are pressed against one another.
(Drywall can be damaged when tightened with excessive force, please be careful.)
→ When tightening the screw use the + driver (manual or motorized) or 8 mm wrench.
4
How to assemble the wall mount support and display
- Always install the display with 2 or more people.
Safety clip screw
* Assembling the wall
mounting bracket,
product and safety
clip.
* Caution
: Prevent the power cord from
being pinched between the wall
mounting bracket and the set
when installing the set.
(A pinched power cord may
cause an electrical short.)
* Locations of the bottom guide spacers
55/65EF9500 ,65EG9600 MODEL 55EG9600/55EG9200 MODEL
Safety clip
1. Set the display with the guide spacer assembled on
the wall mount bracket on the wall in arrow direction.
At this time, align the bottom assembly part and lift the
set up lightly to align the top part.
2. When adjusting the location, assemble the provide
safety clip as shown in the picture to prevent the
product from moving. Tighten the safety clip screw
completely. If the safety clip is not tightened as shown
in the picture, the product can fall off.
→ Pull on the bottom of the set to make sure the
display is secure.
→ When fixing the product with the speaker to the
wall, hold and lift up the product, not the speaker.
→ When installing a display rotated, only rotate the
display 90 degrees (portrait mode).
→ Make sure to keep a certain level of distance from
the wall so that excessive force is not applied on
the cable or accessory.
→ When you push the product with excessive force,
the product can be damaged.
INSTALLATION
- The actual product may differ from the picture.
1
How to Attach the Brackets for the Product to the TV
- If the screw will not fully tighten when using a guide spacer, recheck the assembly depth of the screw and refer to the technical service manual.
Top guide
spacer
Bottom guide
spacer
Guide spacer screw
- Work procedure
1. Check to see if the display has Guide spacer screws
installed into the mounting holes. If so, remove those.
2. Assemble the guide spacer and the guide spacer screw
in order as shown in the picture.
- Place the TV on a table with the screen facing down.
Make sure that you place it on a flat surface covered
with a soft cloth or cushion to protect it from
scratches.
- Secure the guide spacers to the TV with the screws.
Assemble the guide spacer to the set by tightening
the screw. Tighten the screw until the set, guide
spacer and the screw are fully pressing against one
another.
- Use the + driver (manual or motorized) when
tightening the screw.
2
How to attach to masonry walls
Please follow the below direction.
- Check the material of the wall and the thickness of the finishing.
- Use the Wall mount anchor for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry brick and
hallow block that do not crack.
- Do not mount the device on the walls made from plasterboard or medium density fiberboard (MDF). In this case, the anchor and screws must
be inserted into the concrete behind the finish surface. If there is no concrete on the other side, then you must first install a separate hanger to
securely install the anchors and screws.
- When installing the product on wall material not designated, install the product so that each location can withstand the pull out load of
70 kgf (686 N) and shear load of 100 kgf (980 N) or above.
a
b d e
c
Wall mount anchor
Wall mount screw
- Use the Ø 8 mm drill bit for concrete and hammer (Impact) drill.
a. Use a drill bit Ø 8 mm to drill a hole for the anchor location within a depth of 80 mm - 100 mm.
b. Clean the drilled hole.
c. Insert the sealed Wall mount anchor to the hole. (When inserting the anchor, use a hammer.)
d. Set the wall mount on the wall by aligning to the location of the hole. and, set the angle adjusting part to face upward.
e. Align the wall mount screw to the hole and tighten it. Then, fasten the screws at torque of 45 kgf/cm - 60 kgf/cm.
3
How to install the wall mount
When installing on a masonry wall
- When you separate the 8 screws on the wall mount connected to the wall bracket for use with a wooden wall, it is much easier to
install the product.
A
A
A
A
Separate the wall mount screw.
→ When installing the product on a masonry wall, turn the 8
screws on the A part counterclockwise to separate the screw
and bracket.
→ After aligning the wall bracket to the location to install, mark
the part to screw on the wall and then remove the wall
bracket.
→ Refer to next picture to attach the wall bracket.
→ Use a level to check whether the wall mount is level.
Loading ...
Loading ...
Loading ...