Documents: Go to download!
User Manual
- User Manual - (English)
- Owner's Guide - (French)
- Owner's Guide - (Spanish)
- Energy Guide - (English)
- Specification - (English)
- Installation Instruction - (English)
- INSTALLATION
- DOOR REMOVAL INSTRUCTIONS
- INSTALLING DOOR HANDLES
- CONNECTING THE WATER SUPPLY
- CONTROLS - FRIGIDAIRE & FRIGIDAIRE GALLERY DISPENSER
- CONTROLS - NON-DISPENSER MODELS
- CONTROLS - FRIGIDAIRE PROFESSIONAL
- AUTOMATIC ICE & WATER DISPENSER
- AUTOMATIC ICE MAKER - FREEZER (SELECT MODELS)
- STORAGE FEATURES
- STORING FOOD AND SAVING ENERGY
- NORMAL OPERATING SOUNDS AND SIGHTS
- CHANGING THE FILTER
- CARE & CLEANING
- BEFORE YOU CALL
Table of contents
User manual Refrigerator
INSTALLATION
This Use & Care Guide provides general operating instructions for your model. Use the refrigerator only as instructed in this Use & Care Guide. Before starting the refrigerator, follow these important first steps.
Location
-
Choose a place that is near a grounded electrical outlet. Do Not use an extension cord or an adapter plug.
- If possible, place the refrigerator out of direct sunlight and away from the range, dishwasher or other heat sources.
- The refrigerator must be installed on a floor that is level and strong enough to support a fully loaded refrigerator.
- Consider water supply availability for models equipped with an automatic ice maker. If you do not hook up water to the refrigerator, remember to turn the ice maker off
CAUTION
Do Not install the refrigerator where the temperature will drop below 55°F (13°C) or rise above 110°F (43°C). The compressor will not be able to maintain proper temperatures inside the refrigerator.
Do Not block the toe grille on the lower front of your refrigerator. Sufficient air circulation is essential for the proper operation of your refrigerator.
Installation
Allow the following clearances for ease of installation, proper air circulation, and plumbing and electrical connections:
- Sides & Top: 3 /8 inch
- Back : 1 inch
NOTE If your refrigerator is placed with the door hinge side against a wall, you may have to allow additional space so the door can be opened wider.
Door Opening
Your refrigerator should be positioned to allow easy access to a counter or table when removing food. For best use of drawers and freezer baskets, the refrigerator should be in a position where both the refrigerator and freezer doors can be fully opened.
Cabinet Leveling & Refrigerator Door Alignment (if necessary)
Guidelines for final positioning of your refrigerator:
- All four corners of the cabinet must rest firmly on the floor.
- The cabinet should be level at the front and rear.
- The sides should tilt ¼ inch (6 mm) from front to back (to ensure that doors close and seal properly).
- Doors should align with each other and be level
Most of these conditions can be met by raising or lowering the adjustable front rollers. To level the cabinet using the front rollers:
To level the cabinet using the front rollers:
1 Slightly open freezer drawer if the toe grill is installed. Lift the toe grille and gently pull forward.
2 Make initial cabinet adjustments by using the front roller height adjusting screws. Use a 3/8 inch socket wrench to turn the adjustment screws (1 per side).
To raise: turn adjustment screw clockwise.
To lower: turn adjustment screw counterclockwise.
3 Ensure both doors are bind-free with their seals touching the cabinet on all four sides and that cabinet is stable.
4 After unit is leveled, lower anti-tip leg using a 3/8 inch socket wrench until it firmly contacts the floor.
5 Install the toe grille by fitting into place.
To make final door height adjustments:
1. Open freezer drawer to make lower hinge visible.
2. Insert 6mm Allen wrench into the shaft of the lower hinge.
3. Adjust the height by turning clockwise or counterclockwise. Turning clockwise will lower the door. Turning counterclockwise will raise the door. Default setting is to the lowest height when you receive your appliance.
To adjust the flipper mullion:
1 Loosen the screw located on the flipper mullion hinge.
2 Adjust flipper mullion height. For proper connection with the flipper mullion guide, there should be a separation about the thickness of a coin (0.060 inches, or 1.5 mm) between the guide and flipper mullion.
3 Re-tighten screw.
DOOR REMOVAL INSTRUCTIONS
Getting through narrow spaces
If your refrigerator will not fit through an entrance area, you can reduce its size by removing the doors. Check first by measuring the entrance.
To prepare for removing the doors:
1 Make sure the electrical power cord is unplugged from the wall outlet.
2 Open the freezer drawer and remove the toe grille (see Installation section).
3 Remove any food from the door shelves and close the doors
To remove the top hinge covers:
1 Remove the two screws from each cover over the top door hinges.
2 Lift inside edge of hinge cover and tilt back.
To Remove Refrigerator Door:
1 Remove top hinge covers. Trace lightly around the door’s top hinges with a pencil. This makes reinstallation easier.
2 Disconnect the harness by grasping both sides of the connector firmly, depress the latch and pull apart.
3 Detach the water tube from the connector located behind the refrigerator, the connector releases when you press inward on the connector’s outer sleeve. Pull the water tube out toward the front of the unit.
4 Open the refrigerator doors to a 90 degree angle and remove the two screws from the top hinge. Lift and remove door from lower hinge.
5 Unscrew the three lower hinge screws and remove the hinge.
To reinstall the refrigerator doors:
1 Replace the lower hinge screws.
2 Holding the door at a 90 degree angle, drop the pin down into the center hinge opening. Rotate it slightly in either direction until the door falls down into place.
3 Reinstall top hinge.
4 Insert the water line in the top left tunnel pushing from the front to the back of the unit
5 Reconnect the harnesses.
6 Replace the top hinge covers.
7 Reconnect electrical power cord to the wall outlet.
To reset door pin:
If doors are removed at less than a 40 degree angle, the pin returns to the home position. It can be reset by turning the door upside and using a 5/32” Allen wrench to rotate the left hand pin 90 degrees clockwise and the right hand pin 90 degrees counterclockwise.
Removing Freezer Drawer
1 Remove 4 hex head drawer screws.
2 Lift up drawer to remove.
Replacing Freezer Drawer
1 Extend the Freezer slides from the unit.
2 Carefully align support pin with hooks on end of freezer slides and then lower freezer door onto slides.
3 Replace the 4 hex head screws that secure the slides to the door (2 on each side) and tighten.
NOTE To locate the pin, look inside the drawer and the pin is next to the door liner and the slides. Not all parts are shown in the illustration.
INSTALLING DOOR HANDLES
Door Handle Mounting Instructions for Frigidaire & Frigidaire Gallery
1 Remove handles from carton and any other protective packaging.
2 Position fresh food handle end caps over upper and lower pre-installed shoulder bolts (A) that are fastened into door, ensuring the holes for the set screws are facing towards the opposite door.
3 While holding handle firmly against door, fasten upper and lower Allen set screws (B) with supplied Allen wrench.
4 Repeat steps 2 and 3 to install opposite handle. Ensure the holes for the set screws are facing towards the first door
5 Position freezer handle end caps over left and right preinstalled shoulder bolts (A) that are fastened to the door, ensuring the holes for the set screws are facing down.
6 While holding handle firmly against door, loosely tighten right Allen set screw (B) with supplied Allen wrench until there is no gap between handle and door.
7 Still holding the handle firmly to the door, firmly tighten left Allen set screw (B) with supplied Allen wrench.
8 Return to the right Allen set screw (B) and firmly tighten with supplied Allen wrench.
Door Handle Mounting Instructions for Frigidaire Professional®
1 Remove handles from carton and any other protective packaging.
2 Position fresh food handle end over upper and lower preinstalled shoulder bolts (A) that are fastened into door, ensuring the holes for the set screws are facing towards the opposite door.
3 While holding handle firmly against door, fasten further most upper and further most lower Allen set screws (B) with supplied Allen wrench.
4 Repeat steps 2 and 3 to install opposite handle. Ensure the holes for the set screws are facing towards the first door.
5 Firmly tighten the inside Allen set screws.
6 Position freezer handle end over left and right pre-installed handle shoulder bolts (A) that are fastened to the door, ensuring the holes for the set screws are facing down.
7 While holding handle firmly against door, loosely tighten far right Allen set screw (B) with supplied Allen wrench until there is no gap between handle and door.
8 Still holding the handle firmly to the door, firmly tighten far left Allen set screw (B) with supplied Allen wrench.
9 Return to the far right Allen set screw (B) and firmly tighten with supplied Allen wrench.
10 Firmly tighten the inside Allen set screws.
NOTE All set screws should be tightened so the screw is below the surface of the handle. The handles should be drawn tight to freezer and refrigerator doors with no gaps. Opening the opposite door while tightening the Allen screw makes installation easier. The door handle may loosen over time or if it was installed improperly. If this happens, tighten the set screws on the handles.
CONNECTING THE WATER SUPPLY
WARNING To avoid electric shock, which can cause death or severe personal injury, disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator
CAUTION
To Avoid Property Damage:
- Copper or Stainless Steel braided tubing is recommended for the water supply line. Water supply tubing made of ¼ inch plastic is not recommended to be used. Plastic tubing greatly increases the potential for water leaks, and the manufacturer will not be responsible for any damage if plastic tubing is used for the supply line.
- DO NOT install water supply tubing in areas where temperatures fall below freezing.
- Chemicals from a malfunctioning softener can damage the ice maker. If the ice maker is connected to soft water, ensure that the softener is maintained and working properly
IMPORTANT Ensure that your water supply line connections comply with all local plumbing codes.
Before Installing The Water Supply Line, You Will Need:
- Basic Tools: adjustable wrench, flat-blade screwdriver, and PhillipsTM screwdriver
- Access to a household cold water line with water pressure between 30 and 100 psi.
- A water supply line made of ¼ inch (6.4mm) OD, copper or stainless steel tubing. To determine the length of tubing needed, measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe. Then add approximately 7 feet (2.1 meters), so the refrigerator can be moved out for cleaning (as shown).
- A shutoff valve to connect the water supply line to your household water system. DO NOT use a self-piercing type shutoff valve.
- Do not re-use compression fitting or use thread seal tape.
- A compression nut and ferrule (sleeve) for connecting a copper water supply line to the ice maker inlet valve.
NOTE Check with your local building authority for recommendations on water lines and associated materials prior to installing your new refrigerator. Depending on your local/ state building codes, Frigidaire recommends for homes with existing valves its Smart Choice® water line kit 5304490728 (with a 6 ft. Stainless Steel Water Line) and for homes without an existing valve, Frigidaire recommends its Smart Choice® water line kit 5304490717 (with a 20 ft. copper water line with self-tapping saddle valve).
To Connect Water Supply Line To Ice Maker Inlet Valve
1 Disconnect refrigerator from electric power source.
2 Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear. Turn OFF water supply at shutoff valve.
3 Remove plastic cap from water valve inlet and discard cap.
4 If you use copper tubing - Slide brass compression nut, then ferrule (sleeve) onto water supply line. Push water supply line into water valve inlet as far as it will go (¼ inch/6.4 mm). Slide ferrule (sleeve) into valve inlet and finger tighten compression nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 1. If you use braided flexible stainless steel tubing - The nut is already assembled on the tubing. Slide nut onto valve inlet and finger tighten nut onto valve. Tighten another half turn with a wrench; DO NOT over tighten. See Figure 2.
5 With steel clamp and screw, secure water supply line (copper tubing only) to rear panel of refrigerator as shown.
6 Coil excess water supply line (copper tubing only), about 2½ turns, behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface.
7 Turn ON water supply at shutoff valve and tighten any connections that leak.
8 Reconnect refrigerator to electrical power source.
9 To turn ice maker on, lower wire signal arm.
CONTROLS - FRIGIDAIRE & FRIGIDAIRE GALLERY DISPENSER
User Interface (colors and options may vary by model)
Enlarged view of above user interface display menu (colors and options may vary by model)
Options May Vary
Options (∧ or ∨) | Used to enter and exit the options menu and make selections. |
Exit | Toggles the options and run modes. |
Control Locked | While in the locked state, you will not be able to change any settings on the display nor dispense ice and water. The “Control Locked” indicator will flash and an audible warning tone is played. |
Quick Freeze On Off | Activates a faster rate for freezing food and increases ice production in the freezer. Deactivates after 12 hours. |
Ice Maker On Off | Toggles the ice maker in the refrigerator compartment “ON” or “OFF”. In the “Off” state, the indicator will blink when ice is dispensed. |
Display On Off | Toggles the display of the temperature settings On and Off |
Refrigeration Temp | Allows the temperature setpoints to be adjusted. Control temperatures range from +33°F / +1°C to +47°F / +8°C |
Freezer Temp | Allows the temperature setpoints to be adjusted. Control temperatures range from -6°F / -21°C to +6°F / -15°C. |
Mode °F °C | Toggles display from Fahrenheit to Celsius. |
Light | Toggles dispenser light On and Off. |
Power Off | Press and hold for three seconds to turn off the cooling system. It also turns off the ice maker and all dispenser functions. The display will read “power off”. |
Water Filter | Displays the current status of the water filter (Good, Order, or Replace). To reset the filter status to “Good”, press and hold the “set” key for three seconds. |
Air Filter | Displays the current status of the air filter (Good, Order, or Replace). To reset the filter status to “Good”, press and hold the “set” key for three seconds |
Default Settings | While in the default option, press and hold the “set” key for three seconds to reset all refrigerator settings to their factory default settings |
Set (+ or −) | Selects the current menu selection option. |
Water | Press the “water” key to select water. An indicator light will be illuminated above the active feature |
Cube | Press the “cube” key to select cubed ice. An indicator light will be illuminated above the active feature |
Crush | Press the “crush” key to select crushed ice. An indicator light will be illuminated above the active feature |
Setting cooling temperatures (options may vary)
IMPORTANT If you place food within 1 inch in front of the air ports, there may be the chance of freezing food.
ALARMS
Power Failure
In the event of a power failure, the power fail alert will be illuminated. Press set to acknowledge the alarm. Other modes may be turned off until the alarm is acknowledged. While a power fail alert is displayed on the control panel, the unit will continue normal operation. The power fail alert on the control panel will be removed once in the user acknowledges the power fail condition by pressing any key on the control panel. The high temp alarm may also be illuminated until a safe operating range temperature has been reached
Freezer Temp
If the freezer temperature reaches 26°F or greater, the alarm will sound and the temperature will flash. You can disable the alarm by pressing the set key but the “High Temp” indicator will illuminate until the temperature goes below 26°F. Fresh Food Temp If the fresh food temperature reaches 55°F or greater, the alarm will sound and the temperature will flash. You can disable the alarm by pressing the set key but the “High Temp” indicator will illuminate until the temperature goes below 55°F.
Door Ajar
If the freezer or fresh food doors have been left open for five minutes or more, an alarm will sound and the door ajar indicator will illuminate on the display. Press the set key to reset any system alarms.
Flapper
When “Cube” or “Crush” is selected, if the flapper (or ice chute door) is being held open by a jammed ice cube, an alarm will sound for two minutes. The alarm will reset after two minutes or when the ice cube is removed and the set key is pressed to reset.
Sabbath Mode
The Sabbath Mode is a feature that disables portions of the refrigerator and its controls in accordance with observance of the weekly Sabbath and religious holidays within the Orthodox Jewish community. Sabbath Mode is turned ON and OFF by simultaneously pressing and holding both the “∨” and “+” for five seconds. The display shows “Sb” while in Sabbath mode. In the Sabbath Mode, the High Temp alarm is active for health reasons. For example, if the door is left ajar the High Temp alarm is activated. The refrigerator will function normally once the door is closed, without any violation of the Sabbath/Holidays. The High Temp alarm is permitted when cabinet temperature is outside the safe zone for 20 minutes. The alarm silences itself after 10 minutes while the High Temp icon stays lit until the Sabbath mode is exited.
CONTROLS - NON-DISPENSER MODELS
User Interface In-Door Controls (options may vary)
An indicator light will be illuminated above most active features. Touch the icon to activate the options below.
Power On Off | Press and hold for three seconds to turn off the cooling system to clean the refrigerator. The digital displays will read OFF |
Default Settings | Resets all refrigerator settings such as temp, temp display and tones to their factory default settings. |
Quick Freeze | Activates a faster rate for freezing food. |
Quick Ice | Temporarily increases cooling for freezer to increase the production of ice |
Air Filter | Filter condition status is always displayed when door is open. Press and hold for three seconds to reset after filter change |
Water Filter | Press and hold for three seconds to reset after filter change |
Alert Reset | Tones emitted by each key press can be turned off based on user preference. The sounds are muted when the red indicator is lit. Warning signals will stay active. |
F/C | Touch to toggle display from Fahrenheit to Celsius. |
Setting cooling temperatures
Press the + or − indicator to adjust the temperature to the desired setting.
The temperature setting will begin to blink with the first touch. The display will time out after 10 seconds and return to the basic display
Alarms
Door Ajar | If the door has been left open for an extended period of time, an alarm will sound and the door ajar indicator will display on the bottom display of the control panel. The alarm is turned off by closing the door. The alert reset key will blink to prompt the reset of any active alarms. Press this key to reset any system alarms. |
High Temp | In the event of a high temperature condition, the temperature display will blink and display “HI”. After 20 minutes, the alarm will sound and the high temp indicator will be red on the bottom of the control panel. Upon acknowledging the alarm, the highest temperature reached will be displayed and the refrigerator will resume normal operation. In case the high temp alarm is not acknowledged at the first alarm sound time out, when the door is first opened, the alarm sound will be repeated. |
Power Fail | In the event of a power failure, the power fail alert will be displayed and the temperature display will blink until the alert reset icon is pressed, acknowledging the alarm. Other modes may be turned off until the alarm is acknowledged. The power fail alert is turned off and the refrigerator will resume normal operation. The high temp alarm may also be illuminated until a safe operating range temperature has been reached. |
“Sabbath Mode”
The Sabbath Mode is a feature that disables portions of the refrigerator and its controls for, in accordance with observance of the weekly Sabbath and religious holidays within the Orthodox Jewish community.
Sabbath Mode is turned ON and OFF by simultaneously pressing and holding the freezer temp “-” and the refrigerator temp “+” indicators for five seconds. The display shows “Sb” while in Sabbath mode.
In the Sabbath Mode, the High Temp alarm is active for health reasons. For example, if the door is left ajar the High Temp alarm is activated. The refrigerator will function normally once the door is closed, without any violation of the Sabbath/Holidays. The High Temp alarm is permitted when cabinet temperature is outside the safe zone for 20 minutes. The alarm silences itself after 10 minutes while the High Temp icon stays lit until the Sabbath mode is exited.
User Interface In-Door Controls (options may vary)
Power On Off | Press and hold for three seconds to turn off the cooling system to clean the refrigerator. The digital displays will read OFF |
Default Settings | Resets all refrigerator settings such as temp, temp display and tones to their factory default settings. |
ICE MAKER ON-OFF | The Ice Maker is on if the LED above the Icon is illuminated. Ice dispensing will still function. Press and hold the button for 3 seconds to toggle the Ice Maker on and off. |
POWERPLUS FREEZE | Activates a faster rate for freezing food and increases ice production in the freezer. Deactivates after 12 hours |
Air Filter | Displays the current status of the air filter (GOOD, ORDER, or REPLACE). To reset the filter status to “GOOD”, press and hold for three seconds. |
Water Filter | Displays the current status of the water filter (GOOD, ORDER, or REPLACE). To reset the filter status to “GOOD”, press and hold for three seconds. |
MUTE ALARM | Tones emitted by each key press can be turned off based on user preference. The sounds are muted when the red indicator is lit. Warning signals will stay active. |
REFRIGERATOR TEMP | Allows the temperature setpoints to be adjusted. Press the “-” or “+” indicator to adjust the temperature to the desired setting. Control temperatures range from +33°F / +1°C to +47°F / +8°C. |
FREEZER TEMP | Allows the temperature setpoints to be adjusted. Press the “-” or “+” indicator to adjust the temperature to the desired setting. Control temperatures range from -6°F / -21°C to +6°F / -15°C |
C/F | Toggles display between Clesius and Fahrenheit |
CONTROLS - FRIGIDAIRE PROFESSIONAL
Dispenser Controls (options may vary)
ALARMS
Power Failure
In the event of a power failure, the power fail alert will be illuminated. Press set to acknowledge the alarm. Other modes may be turned off until the alarm is acknowledged. While a power fail alert is displayed on the control panel, the unit will continue normal operation. The power fail alert on the control panel will be removed once in the user acknowledges the power fail condition by pressing any key on the control panel. The high temp alarm may also be illuminated until a safe operating range temperature has been reached
Freezer Temp
If the freezer temperature reaches 26°F or greater, the alarm will sound and the temperature will flash. You can disable the alarm by pressing the set key but the “High Temp” indicator will illuminate until the temperature goes below 26°F. Fresh Food Temp If the fresh food temperature reaches 55°F or greater, the alarm will sound and the temperature will flash. You can disable the alarm by pressing the set key but the “High Temp” indicator will illuminate until the temperature goes below 55°F.
Door Ajar
If the freezer or fresh food doors have been left open for five minutes or more, an alarm will sound and the door ajar indicator will illuminate on the display. Press the set key to reset any system alarms.
Flapper
When “Cube” or “Crush” is selected, if the flapper (or ice chute door) is being held open by a jammed ice cube, an alarm will sound for two minutes. The alarm will reset after two minutes or when the ice cube is removed and the set key is pressed to reset.
Sabbath Mode
The Sabbath Mode is a feature that disables portions of the refrigerator and its controls in accordance with observance of the weekly Sabbath and religious holidays within the Orthodox Jewish community. Sabbath Mode is turned ON and OFF by simultaneously pressing and holding both the “∨” and “+” for five seconds. The display shows “Sb” while in Sabbath mode. In the Sabbath Mode, the High Temp alarm is active for health reasons. For example, if the door is left ajar the High Temp alarm is activated. The refrigerator will function normally once the door is closed, without any violation of the Sabbath/Holidays. The High Temp alarm is permitted when cabinet temperature is outside the safe zone for 20 minutes. The alarm silences itself after 10 minutes while the High Temp icon stays lit until the Sabbath mode is exited.
AUTOMATIC ICE & WATER DISPENSER
Priming the water supply system
1 Begin filling the system by pressing and holding a drinking glass against the water dispenser paddle.
2 Keep the glass in this position until water comes out of the dispenser. It may take about 1½ minutes.
3 Continue dispensing water for about four minutes to flush the system and plumbing connections of any impurities (stopping to empty the glass as necessary).
Ice maker operation & care
After the refrigerator is installed properly and has cooled for several hours, the ice maker can produce ice within 24 hours. The ice maker will fill the ice bin from the rear. You must dispense some ice to force the ice forward in the bin. This will allow the bin to fill completely.
Ice Maker and Storage Bin Capacity
This ice maker should produce 2.0 to 2.5 pounds of ice per 24 hours. In a Standard Depth model, the ice bin will hold about 6.5 pounds of ice. In a Counter Depth model, the ice bin will hold about 4 pounds of ice
Turning the fresh food ice maker on and off
Ice production is controlled by the ice maker’s On/Off feature on the control panel. Pressing the On/Off feature turns the ice maker on & off.
Using the ice maker after installation
Before making ice for the first time, be sure to prime the water supply system. Air in new plumbing lines can result in two or three empty ice maker cycles. Furthermore, if the system is not flushed, the first ice cubes may be discolored or have an odd flavo
Ice maker/dispenser tips
- If your refrigerator is not connected to a water supply or the water supply is turned off, turn off the ice maker as described in the previous section.
- The following sounds are normal when the ice maker is operating:
- Motor running
- Ice dropping into ice bin
- Water valve opening or closing
- Running water
- If you need a large quantity of ice at one time, it is best to get cubes directly from the ice bin
- Ice cubes stored too long may develop an odd flavor. Empty the ice bin as explained below
- When dispensing cubed ice, it is normal to have a small quantity of little pieces along with the whole cubes.
- To avoid splashing, dispense ice into your container before adding liquids.
- It is normal for ice to fill to the top of the ice bin.
Cleaning the ice maker
Clean the ice maker and ice bin at regular intervals, especially prior to vacation or moving.
1 Turn off the ice maker.
2 Remove the ice bin by pulling straight out.
3 Empty and carefully clean the ice bin with mild detergent. Do not use harsh or abrasive cleaners. Rinse with clear water.
4 Allow the ice bin to dry completely before replacing in the freezer. 5 Replace the ice bin. Turn the ice maker on.
Remove and empty the ice bin if:
- An extended power failure (one hour or longer) causes ice cubes in the ice bin to melt and refreeze together after power is restored, jamming the dispenser mechanism.
- You do not use the ice dispenser frequently. Ice cubes will freeze together in the bin, jamming the dispenser mechanism.
Remove the ice bin and shake to loosen the cubes or clean as explained above.
AUTOMATIC ICE MAKER - FREEZER (SELECT MODELS)
Operation & Care of the Freezer Ice Maker (select models)
After the refrigerator is installed properly, the ice maker can produce ice within 24 hours. When using the ice maker for the first time, and in order for it to work properly, it is necessary to clear air from the water tubing and the filter. Furthermore, if the system is not flushed, the first ice cubes may be discolored or have an odd flavor. Once the ice maker begins making ice, allow the bin to fill completely, then discard the first FULL bin of ice on a Standard Depth model, and the first TWO FULL bins of ice on a Counter Depth model.
Ice Maker and Storage Bin Capacity
This ice maker should produce between 2 and 2.5 pounds of ice per 24 hours depending on usage conditions. In a Standard Depth model, the ice bin will hold about 12 pounds of ice. In a Counter Depth model, the ice bin will hold about 7 pounds of ice.
Turning the ice maker on and off
The ice maker is turned off and on by lifting/ lowering the ice maker’s wire signal arm. To gain access to the ice maker, pull the freezer drawer out. Lift the wire signal arm to turn the ice maker OFF and lower the wire signal arm to turn it ON
Ice maker tips
- The following sounds are normal when the ice maker is operating:
- Motor running
- Ice dropping into ice bin
- Water valve opening or closing
- Running water
- Ice cubes stored too long may develop an odd flavor. Empty the ice bin as explained below
Quick Freeze Function
Your refrigerator is equipped with a Quick Freeze Function for freezing food at a faster rate, but it can also increase ice production. This function terminates automatically after 12 hours. This function affects only the ice maker in the freezer
Cleaning the ice maker
Clean the ice maker and ice bin at regular intervals, especially prior to vacation or moving.
1 Turn off the ice maker.
2 Remove the ice bin.
3 Empty and carefully clean the ice bin with mild detergent. Do not use harsh or abrasive cleaners. Rinse with clean water.
4 Allow the ice bin to dry completely before replacing in the freezer.
5 Replace the ice bin. Turn the ice maker on.
Remove and empty the ice bin if an extended power failure (one hour or longer) causes ice cubes in the ice bin to melt and refreeze together after power is restored. Remove the ice bin and shake to loosen the cubes or clean as explained above.
STORAGE FEATURES
You can easily adjust shelf positions in the fresh food compartments to suit your needs. The shelves have mounting brackets that attach to slotted supports at the rear of each compartment.
Change the Position of a Shelf
1 Remove all food from shelf.
2 Lift the front edge up and pull the shelf out.
3 Replace by inserting the mounting bracket hooks into the desired support slots.
4 Lower the shelf and lock into position
Reposition the Air Seal
For crisper shelves:
1 Remove air seal by pushing down on the flap with a downward rotation.
2 Position the air seal towards the outside end of the shelf to avoid the air tower when shelf is pushed back into place.
3 Install seal by sliding lower tab of seal up into bottom rear slot of shelf with seal at a downward angle then pulling up on seal flap until seal sits snug on back of shelf and flap sits at about a 10 degree angle from shelf surface.
For glass shelves:
1 Remove air seal by pushing seal straight back.
2 Position the air seal towards the outside edge of the shelf to avoid the air tower when shelf is pushed back into place.
3 Install seal by sliding the open channel end of the seal onto back edge of shelf until seal sits snug on back of shelf and flap sits at about a 10 degree angle from shelf surface.
Drawers
Your refrigerator includes a variety of storage drawers.
Crispers
Crisper drawers are designed for storing fruits, vegetables, and other fresh produce.
Crisper humidity control
Crisper drawers include a sliding control for adjusting the humidity inside the crisper. Leafy vegetables keep best when stored with the Humidity Control set on Higher Humidity. Fresh fruits keep best when stored with the Humidity Control set on Lower Humidity.
To remove the Crisper Drawer for cleaning:
1 Pull the drawer out until it stops.
2 Lift the front slightly and remove the drawer.
Deli drawer
Ideal for storage of deli meats, cheese, and beverages.
Doors
Storage bins (varies by model)
The doors to your fresh food compartment use a system of modular storage bins. All of these bins are removable for easy cleaning. Some of them have fixed positions, while others can be adjusted to your needs. Door bins are ideal for storing jars, bottles, cans, and large drink containers. They also enable quick selection of frequently used items.
To change the position of an adjustable door bin:
1 Remove all food from door bin.
2 Grip the bin firmly with both hands and lift it upward.
3 Remove the bin.
4 Place the bin just above desired position.
5 Lower the bin onto supports until locked in place
6 Place bin liner into bin.
Accessories (varies by model)
Removable Can Dispenser
The can dispenser holds six (12 ounce) cans. Insert cans into top of bin and dispense from the bottom.
Dairy compartment
Use the dairy compartment, at the top of the fresh food compartment door, for shortterm storage of cheese, spreads, or butter. The dairy compartment is designed to be warmer than the open area and includes a lift-up cover and a dairy divider (select models).
To Remove Upper Freezer Basket
1 Find the side where the basket frame is aligned to the clip opening. The basket frame should be aligned to both front and rear clips on the same side (either left or right side).
2 If the basket frame is not aligned to the left or right side, push the basket sideways (to either side) until it is aligned.
3 By grabbing the basket wire frame close to the frontal clip, pull up to take the basket frame out.
4 Grab the basket frame close to the rear clip and pull up until it comes out of the clip.
5 Once one side of the basket is off the clips or retainers, slide the basket sideways until the other side of the frame is aligned with the clip openings on the opposite side of the freezer.
6 In the same way, pull up the basket frame from the frontal and rear clips until it is out of the clips.
7 Remove the basket.
Reverse the steps to reinstall the basket.
Removing Freezer Basket Instructions
1 Locate the basket clips in the rear corners of the basket and pull them out to remove.
2 Open fresh food doors completely.
3 Lift the basket up and remove.
Replacing Freezer Basket Instructions
1 Place freezer basket back inside the freezer drawer.
2 Replace clips by sliding them back into the slots.
Dividers Removal
Lift up on the front of the upper divider and pull out.
Squeeze handle and lift up in the center of the divider to move it side-to-side. (The divider cannot be removed.)
Tilt Wire Shelf
The freezer tilt wire shelf (located on the inside of the freezer drawer) is not designed to be removed.
STORING FOOD AND SAVING ENERGY
Ideas for storing foods
Fresh food storage
- Keep the fresh food compartment between 34°F and 40°F with an optimum temperature of 37°F.
- Avoid overcrowding the refrigerator shelves, which reduces air circulation and causes uneven cooling.
- Avoid placing food in front of air ports. (See Controls Section for illustration.)
Fruits and vegetables
- Store fruits and vegetables in crisper drawers, where trapped moisture helps preserve food quality for longer time periods.
- Wash items and remove excess water.
- Wrap any items that have strong odors or high moisture content.
Meat
- Wrap raw meat and poultry separately and securely to prevent leaks and contamination of other foods or surfaces.
- Use the deli drawer to store meat/poultry for short-term storage. Any meat to be kept longer than two days should be frozen.
Frozen food storage
- Keep the freezer compartment at 0°F or lower.
- A freezer operates most efficiently when it is at least ⅔ full.
Packaging foods for freezing
- To minimize food dehydration and quality deterioration, use aluminum foil, freezer wrap, freezer bags, or airtight containers. Force as much air out of the packages as possible and seal them tightly. Trapped air can cause food to dry out, change color, and develop an off-flavor (freezer burn).
- Wrap fresh meats and poultry with suitable freezer wrap prior to freezing.
- Do not refreeze meat that has completely thawed.
Loading the freezer
- Prior to grocery shopping, activate “quick freeze” so that on your return you can ensure your newly purchased food designated for the freezer will be preserved as quickly as possible.
- Activating “quick freeze” also will help your freezer more efficiently maintain the selected temperature after placing new purchases with pre-existing frozen foods.
- Avoid adding too much warm food to the freezer at one time. This overloads the freezer, slows the rate of freezing, and can raise the temperature of frozen foods.
- Leave a space between packages, so cold air can circulate freely, allowing food to freeze as quickly as possible.
Ideas for saving energy
Installation
- Locate the refrigerator in the coolest part of the room, out of direct sunlight, and away from heating ducts or registers.
- Do not place the refrigerator next to heat-producing appliances such as a range, oven, or dishwasher. If this is not possible, a section of cabinetry or an added layer of insulation between the two appliances will help the refrigerator operate more efficiently.
- Level the refrigerator so that the doors close tightly.
Temperature settings
- Refer to the “Controls” section for procedures on temperature settings.
Food storage
- Avoid overcrowding the refrigerator or blocking cold air vents. Doing so causes the refrigerator to run longer and use more energy.
- Cover foods and wipe containers dry before placing them in the refrigerator. This cuts down on moisture build-up inside the unit.
- Organize the refrigerator to reduce door openings. Remove as many items as needed at one time and close the door as soon as possible.
- Do not place a hot container directly on a cold shelf. Remember, such an extreme temperature change may damage the glass.
NORMAL OPERATING SOUNDS AND SIGHTS
Understanding the sounds you may hear
Your new, high-efficiency refrigerator may introduce unfamiliar sounds. These sounds normally indicate your refrigerator is operating correctly. Some surfaces on floors, walls, and kitchen cabinets may make these sounds more noticeable.
The following is a list of major components in your refrigerator and the sounds they can cause:
A Evaporator Refrigerant through the evaporator may create a boiling or gurgling sound.
B Evaporator fan You may hear air being forced through the refrigerator by the evaporator fan.
C Defrost heater During defrost cycles, water dripping onto the defrost heater may cause a hissing or sizzling sound. After defrosting, a popping sound may occur.
D Automatic ice maker When ice has been produced, you will hear ice cubes falling into the ice bin. Ice maker fan, water valve activation, and refrigerant gas fluid may create sounds from its operation.
E Electronic control & automatic defrost control These parts can produce a snapping or clicking sound when turning the cooling system on and off.
F Condenser fan You may hear air being forced through the condenser.
G Compressor Modern, high-efficiency compressors run much faster than older models. The compressor may have a highpitched hum or pulsating sound.
H Water valve Makes a buzzing sound each time it opens to fill the ice maker.
I Drain pan (not removable) You may hear water dripping into the drain pan during the defrost cycle.
J Condenser May create minimal sounds from forced air. K Motorized damper May produce a light humming during operation.
L Ice dispensing paddle When dispensing ice, you will hear a snapping, clicking, or popping sound.
CHANGING THE FILTER
Air filter (Frigidaire Gallery/Professional)
The air filter is located at the top of the air tower.
Replacing your PureAir Ultra IITM air filter
To ensure optimal filtering of refrigerator odors, you should change the air filter every six months (the filter status light on the Touch Panel prompts you to replace the filter after six months).
1 Insert fingers in circled area.
2 Push clips in to release front cover.
3 Remove front cover by pulling towards you and lifting up.
4 Replace air filter by sliding into slots.
5 Installation of front cover is reverse of removal.
6 To reset Air Filter status, refer to instructions under “Controls Section”.
Ordering replacement filters
Order new filters by calling 877-808-4195, online at www.frigidaire.com/store, or through the dealer where you bought your refrigerator. You may want to consider ordering extra filters when you first install your refrigerator.
Air Filter Replacement cartridge, part #PAULTRA2
Locating the Filters
Your refrigerator is equipped with water filtering system. The water filter system filters all dispensed drinking water, as well as the water used to produce ice.
Water Filter
The water filter is located at the top right side of the fresh food compartment.
Replacing the Water Filter
In general, you should change the water filter every six months to ensure the highest possible water quality. Water Filter Status on the user interface prompts you to replace the filter after a standard amount of water (125 gallons/473 liters for PureSource Ultra IITM) has flowed through the system.
If your refrigerator has not been used for a period of time (during moving for example), change the filter before reinstalling the refrigerator
More about your Advanced Water Filter
The PureSource UltraTM ice and water filter system is tested and certified to NSF/ANSI Standards 42 and 53 for the reduction of claims specified on the performance data sheet.
The PureSource 3TM ice and water filter system is tested and certified to NSF/ANSI Standards 42 and 53 for the reduction of claims specified on the performance data sheet.
Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts.
Test & certification results:
- Rated Capacity - 200 gallons/757 liters for PureSource UltraTM and PureSource 3TM ice and water filter
- Rated service flow - .50 gallons per minute
- Operating Temp.: Min. 33°F, Max. 100°F
- Maximum Rated Pressure - 100 pounds per square inch
- Recommended Minimum Operating Pressure: 30 pounds per square inch
To replace your PureSource 3TM water filter:
It is not necessary to turn the water supply off to change the filter. Be ready to wipe up any small amounts of water released during the filter replacement.
1 Turn Off the ice maker.
2 Remove the filter by pushing on the end/face of the filter.
3 Slide the old water filter cartridge straight out of the housing and discard it.
4 Unpackage the new filter cartridge. Using the alignment guide, slide it gently into the filter housing until it stops against the snap-in connector at the back of the housing.
5 Push firmly until the cartridge snaps into place (you should hear a click as the cartridge engages the snap-in connector).
6 Press a drinking glass against the water dispenser while checking for any leaks at the filter housing. Any spurts and sputters that occur as the system purges air out of the dispenser system are normal.
7 After filling one glass of water, continue flushing the system for about four minutes.
8 Turn On the ice maker.
9 Press and hold the Water Filter button on the Ice & Water Dispenser control panel for three seconds. When the display changes from “Red” to “Green,” the status has been reset.
CARE & CLEANING
Protecting your investment
Keeping your refrigerator clean maintains appearance and prevents odor build-up. Wipe up any spills immediately and clean the freezer and refrigerator compartments at least twice a year.
When cleaning, take the following precautions:
- Never use CHLORIDE or cleaners with bleach to clean stainless steel.
- Do not wash any removable parts in a dishwasher.
- Always unplug the electrical power cord from the wall outlet before cleaning.
- Remove adhesive labels by hand. Do not use razor blades or other sharp instruments which can scratch the appliance surface.
- Remove adhesive labels by hand. Do not use razor blades or other sharp instruments which can scratch the appliance surface.
- Do not remove the serial plate. Removal of your serial plate voids your warranty.
- Before moving your refrigerator, raise the anti-tip brackets so the rollers will work correctly. This will prevent the floor from being damaged.
NOTE If you set your temperature controls to turn off cooling, power to lights and other electrical components will continue until you unplug the power cord from the wall outlet.
Vacation and moving tips
Occasion | Tips |
Short Vacations |
|
Long Vacations |
|
Moving |
|
Care & Cleaning Tips |
Part | What To Use | Tips and Precautions |
Interior & Door Liners |
|
Use two tablespoons of baking soda in one quart of warm water. Be sure to wring excess water out of sponge or cloth before cleaning around controls, light bulb or any electrical part. |
Door Gaskets |
|
Wipe gaskets with a clean soft cloth |
Drawers & Bins |
|
Use a soft cloth to clean drawer runners and tracks |
Glass Shelves |
|
Allow glass to warm to room temperature before immersing in warm water. |
Toe Grille |
|
Vacuum dust from front of toe grille. Remove toe grille (see Installation Instructions). Vacuum backside, wipe with sudsy cloth or sponge. Rinse and dry |
Exterior & Handles |
|
Do not use commercial household cleaners containing ammonia, bleach or alcohol to clean handles. Use a soft cloth to clean smooth handles. DO NOT use a dry cloth to clean smooth doors. |
Exterior & Handles (Stainless Steel Models Only) |
|
Never use CHLORIDE or cleaners with bleach to clean stainless steel. Clean stainless steel front and handles with non-abrasive soapy water and a dishcloth. Rinse with clean water and a soft cloth. Use a non-abrasive stainless steel cleaner. These cleaners can be purchased at most home improvement or major department stores. Always follow manufacturer’s instructions. Do not use household cleaners containing ammonia or bleach. NOTE: Always clean, wipe and dry with the grain to prevent scratching. Wash the rest of the cabinet with warm water and mild liquid detergent. Rinse well, and wipe dry with a clean soft cloth. |
BEFORE YOU CALL
Concern | Potential Cause | Common Solution |
Automatic Ice Maker | ||
Ice maker is not making any ice. |
|
|
Automatic Ice Maker (Cont’d) |
|
|
Ice maker is not making enough ice. |
|
|
Freezer ice maker will not stop making ice (select models). |
|
|
Ice cubes are freezing together. |
|
|
Dispenser (Ice & Water) |
|
|
Dispenser will not dispense ice. |
|
|
Ice dispenser is jammed. |
|
|
Dispenser will not dispense water. |
|
|
Water not cold enough |
|
|
Water has an odd taste and/or odor |
|
|
Opening/Closing Of Doors/Drawers |
|
|
Door(s) will not close. |
|
|
Drawers are difficult to move. |
|
|
Running of Refrigerator |
|
|
Compressor does not run |
|
|
Refrigerator seems to run too much or too long |
|
|
Digital Temperature Setting Display |
|
|
Digital temperature displays an error. |
|
|
Water/Moisture/Frost Inside Refrigerator |
|
|
Moisture collects on inside of refrigerator walls |
|
|
Water collects on bottom side of drawer cover. |
|
|
Water collects in bottom of drawer |
|
|
Water/Moisture/Frost Outside Refrigerator |
|
|
Moisture collects on outside of refrigerator or between doors. |
|
|
Food in Fresh Food Compartment |
|
|
Food is freezing. |
|
|
See other models: FFHD2250TD FGHD2368TD FFRE4120SW FFSE5115PW FGIC3067MB