Model Name/Nombre de Modelo**=color number/número de color
LSC27925**
P/No. MFL63719706
ENGLISH ESPAÑOL
www.lg.com
OWNER’S MANUAL
SIDE BY SIDE
REFRIGERATOR
Please read this manual carefully before operating your set
and retain it for future reference.
MANUAL DE USUARIO
REFRIGERADOR
DE DOS PUERTAS
Lea detenidamente este manual antes de empezar a utilizar
el refrigerador y guárdelo como referencia para el futuro.
1
WARRANTY
Visit our web site http://www.lg.com LG Electronics
LIMITED WARRANTY
United States of America
LG Electronics will repair or at its option replace, without charge, your product which proves to be defective
in material or workmanship under normal use during the warranty period listed below from the date of original
purchase.
This warranty is good only to the original purchaser of the product during the warranty period as long as it is in the
U.S. including Alaska, Hawaii, and U.S. Territories.
LG Refrigerator / Freezer Warranty Period
Product Parts Labor
Refrigerator / Freezer 1 year 1 year [In-Home Service (Except Model GR-051)]
Sealed System
(Compressor, Condenser, Evaporator)
7 years 1 year [In-Home Service (Except Model GR-051)]
No other express warranty is applicable to this product. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING
THE IMPLIED WARRANTY OF MERCHANTABILITY, IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY
HEREIN. LG ELECTRONICS SHALL NOT BE LIABLE FOR THE LOSS OF USE OF THE PRODUCT, INCONVENIENCE
OR ANY OTHER DAMAGES, DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OF OR INABILITY TO USE
THIS PRODUCT OR FOR ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING THE IMPLIED
WARRANTY OF MERCHANTABILITY APPLICABLE TO THIS PRODUCT.
Some States do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an
implied warranty lasts; so these limitations or exclusions may not apply to you. This warranty gives you specic legal rights
and you may also have other rights which vary from state to state.
THE ABOVE WARRANTY DOES NOT APPLY TO:
1. Service trips to your home to deliver and pickup, install, instruct, or replace house fuses or correct house wiring or
plumbing, or correction of unauthorized repairs.
2. Damage to the product caused by accident, pests, re, oods, or acts of God.
3. Repairs when your LG product is used in other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, or improper installation.
5. Damages caused during and/or after delivery.
6. Display, discount, or refurbished units purchased with scratches, dents, or defects.
Proof of purchase is required and must be provided to LG in order to validate warranty.
Therefore, these costs are paid by the consumer.
If the product is installed outside the normal service area, any cost of transportation involved in the repair of the product,
or the replacement of defective parts, shall be borne by the owner.
CUSTOMER ASSISTANCE NUMBERS:
To obtain Warranty Coverage: Retain your Bill of Sale to prove date of purchase.
A Copy of your Sales Receipt must be submitted at the time warranty service is
provided.
To obtain Product or Customer: Call 1-800-243-0000 (24 hrs a day, 7 days per week, 365 days per year).
Service Assistance: Press the appropriate menu option, and have your product type (Refrigerator),
model number, serial number, and ZIP/Postal Code ready.
To obtain the nearest Authorized
Service Center:
Call 1-800-243-0000 (24 hrs a day, 7 days per week, 365 days per year)
Press the appropriate option, and have your product type (Refrigerator), model
number, serial number, and ZIP/Postal Code ready.
3
GARANTÍA
Warranty (USA) 1-2
English Version 3-25
Spanish Version 26-49
Important Safety Instructions 4-5
Requirements for Ground Connection 5
Refrigerator Installation 6-11
Unpacking your Refrigerator 6
Installation 6
Base Grille Installation 6
Handle Removal 6-7
Handle Installation 7
Removing and Replacing
Refrigerator Doors 7-8
Door Alignment 8
Connecting the Water Line 9-11
Refrigerator Features 12
Using your Refrigerator 13-17
Ensuring Proper Air Circulation 13
Prior to Use 13
Control Panel Features 13
Refrigerator and Freezer Controls 13-14
Adjusting Control Settings 14
Ice maker Operation 14-15
Food Storage Guide 15
Storing Frozen Food 15
Water and Ice Dispenser 16
Ice Storage Bin 16
Ice maker Cover 16
Door and Rack Support 16
Snack Pan 16
Crisper and Crisper Cover 17
Humidity Controls 17
Refrigerator Shelves 17
Freezer Shelf 17
Filter 18-19
Water Filter 18
Performance Data Sheet 19
Care and Cleaning 20-21
General Cleaning Tips 20
Outside 20
Inside Walls 20
Door Liners & Gaskets 20
Plastic Parts (Covers and Panel) 20
Back Cover 20
Light (LED) Replacement 20
Power Interruptions 20-21
When you go on Vacation 21
When you Move 21
When you should set the Ice maker
Power Switch to off 21
Normal Sounds you May Hear 21
Troubleshooting Guide 22-25
TABLE OF CONTENTS
4
This manual contains several important safety notices. Always read and obey all of the following safety messages.
This is the safety alert symbol. This symbol is a warning to potential dangers that could cause death, injury or
damage to you, others or the product. All safety messages will follow after this warning symbol and the word
“DANGER”, “CAUTION” or “WARNING”. These words mean:
You may be killed or suffer fatal damage if you do not follow instructions.
You may be killed or seriously injured if you do not follow instructions.
Indicates a potentially hazardous situation which, if not avoided, may result in minor injury
or damage to the product.
All safety messages inform you of potential danger, advise you on how to reduce the risk of injury and tell you what can
occur if the instructions are not followed.
To reduce the risk of fire, electrical shock or personal
injury, the following precaution measures should be
followed:
•NEVER disconnect the refrigerator by pulling the power
cord, always grip the plug firmly and disconnect it
directly from the outlet.
•Immediately repair or replace all faulty or damaged
service cables. Do not use cords that have cracks or
abrasion damage on the length of the cord or on the
plug.
•When moving your refrigerator, take care not to roll over
the electrical cord.
•DO NOT store or use gasoline or other combustible
liquids or vapors in proximity with this or any other
electrical appliance.
•DO NOT permit children to climb, stand or swing from
the doors or shelves of the refrigerator. This can cause
serious injury to them and damage to the product.
•Keep your fingers away from areas in which they
can become caught, such as the doors, hinges and
cabinets. Be careful closing the doors when children
are near.
•Unplug the refrigerator before cleaning or repairing.
NOTE: We strongly recommend that any repair services
be performed by a qualified professional.
•Before replacing a burned-out light bulb, unplug the
refrigerator or shut down the circuit breaker to avoid
contact with a live wire (the bulb could break while
being replaced). NOTE: Setting the control to the OFF
position does not disconnect the power from the light
bulb circuit.
•Do not keep bottles in the freezer compartment, they
could explode after freezing and cause damage.
•For your safety, this product should be properly
grounded. Have a qualified professional check the
electrical circuit and outlet to ensure a proper ground
connection.
•Read all instructions before utilizing the product. Utilize
this product only as explicitly expressed in this guide.
•Once the refrigerator is operating, avoid touching cold
surfaces of the freezer with damp or wet hands; the
skin could become adhered to these surfaces.
•In refrigerators with an automatic ice dispenser, avoid
contact with moving parts of the ejector mechanism
or with the heating mechanism that discharges the
cubes. DO NOT place your fingers or hands in the
ice dispenser mechanism while the refrigerator is
connected.
•DO NOT refreeze foods which have already thawed. The
Department of Agriculture of the United States, in your
Bulletin of Home and Gardens No. 69 establishes that:
“...You can refreeze food that has thawed if they contain
ice crystals or are cold and below 40 °F (4 °C)”.
“...Ground beef, perishable food or seafood that is
discolored or has an unpleasant odor should not be
frozen or consumed. Consumption of melted ice cream
should also be avoided. If the odor or color of food is
questionable, discard it. The food may be dangerous to
consume”.
“Partial thawing or refreezing reduces the quality of the
food, especially fruit, vegetables and prepared meals.
The quality of red meat is less affected than other foods.
Use refrozen products as soon as possible in order to
maintain their quality”.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
SAFETY MESSAGES
WARNING
DANGER
WARNING
CAUTION
5
IMPORTANT SAFETY INSTRUCTIONS
This appliance is not intended for use by children, persons with physical or mental disabilities, persons with reduced
sensory or mental capacity, or persons with lack of experience or know-how, unless they have supervision or instruction
in relation to the use of the appliance by the person responsible for their safety. Children should be supervised to
assure that they do not play with the appliance.
Children becoming trapped or suffocated is not
a problem of the past. Discarded and abandoned
refrigerators are a hazard, even if they remain there
“for just a few days”. If you would like to dispose of
your old refrigerator, please follow the instructions
below to prevent any accidents.
BEFORE DISPOSING YOUR REFRIGERATOR OR
FREEZER WHEN NO LONGER IN USE:
•Removethedoors.
•Leavetheshelvesinplacesothatchildrencannot
easily become stuck in them.
Your old refrigerator may have a cooling system that
uses CFC’s (chlorofluorocarbons). CFC affects the
stratospheric layer of the ozone.
If you decide to throw out your old refrigerator, ensure
that CFC contaminants are properly disposed of by a
qualified professional. If you intentionally remove the
CFC refrigerant, you could be subject to fines or prison in
accordance with environmental legislation in effect.
IMPORTANT: Attentively read the following.
TO CONNECT ELECTRICITY
WARNING
ELECTRICAL SHOCK HAZARD
FOR YOUR PERSONAL SAFETY, this appliance must
be properly grounded. Have a qualified electrician
check your wall outlet to ensure that the plug is
grounded properly.
3 prong
grounding type
wall receptacle
3 prong Ensure proper
grounding ground exists
plug before use
RECOMMENDED GROUNDING METHOD
Your refrigerator must always be plugged to its own outlet
which is adequately grounded. The energy current should
only be 115 V, 60 Hz, A.C. and fused at 15 or 20 A. This
provides the best performance and prevents an overload
which could cause a fire from the overheating of the
cables. It is recommended that a separate circuit be used
for this appliance, as well as a receptacle that cannot be
disconnected with a switch.
Do not use an extension cable.
It is your responsibility and obligation to replace two-
prong outlets with that of an adequately grounded three-
prong outlet.
Do not, under any circumstance, cut or extract the third
prong from the plug.
NOTE: Before installation, cleaning or replacing light
bulbs, you must disconnect the appliance from the power
source. When finished, plug the appliance back in and
adjust the thermostat to the desired position.
USE OF EXTENSION CABLES
We do not recommend the use of extension cables.
However, if you still choose to utilize an extension cable,
it is absolutely necessary that it is listed in the UL (in the
United States) or CSA (in Canada), that it supports three-
pronged plugs and that the electrical current support a
minimum of 15 A and 120 V.
The use of an extension cable will increase the amount of
space needed behind the refrigerator.
WARNING
REPLACING ELECTRICAL CABLE
If the power cord is damaged, it must be replaced by
our service center or qualified LG technician to avoid
any risk.
CAUTION
DANGER: CHILDREN MAY BECOME TRAPPED
CFC DISPOSAL
REQUIREMENTS FOR GROUND CONNECTION
6
REFRIGERATOR INSTALLATION
WARNING
EXCESSIVE WEIGHT HAZARD
Use the assistance of two or more persons to move or
install the refrigerator. Not following these instructions
may cause injury to the back and other parts of the
body.
UNPACKING YOUR REFRIGERATOR
Before installing your refrigerator, remove any tape or
temporary stickers. Do not remove any stickers that feature
warnings, the model serial number or the technical label
of the product located on the back of the refrigerator.
To remove adhesive tape residue, rub it well with your
fingers and a little liquid detergent. Clean with warm water
and let dry.
Do not use sharp instruments, rubbing alcohol, flammable
liquids or abrasive cleaning products to remove the
adhesive tape or glue. These products can damage the
surface of your refrigerator. For more information, see the
section on “Important Safety Instructions”.
The shelves come already installed in their factory position.
Remove the shelves and replace them according to your
spacing needs.
WARNING
WHEN MOVING YOUR REFRIGERATOR
Your refrigerator is extremely heavy. Make sure you
protect the floor when moving your refrigerator for
cleaning or servicing. Always pull your refrigerator
straight out when moving it. Do not shift from side to
side or “walk” the refrigerator when attempting to move
it as this can cause damage to the floor.
WARNING
EXPLOSION HAZARD
Keep all flammable materials and vapors (such as
gasoline) away from the refrigerator. Not following
these instructions may cause death, explosion or fire.
INSTALLATION
1. Avoid placing the unit near heat sources, direct sunlight
or humidity.
2. To minimize noise and vibration, the refrigerator MUST
be installed on a solidly constructed floor.
3. Carpeting and soft tile surfaces are not recommended.
4. NEVER install the refrigerator on a platform or a weakly
supported structure.
5. Install this appliance in an area where the temperature
is between 41 °F (5 °C) and 110 °F (43 °C). If the
temperature around the appliance is too low or high,
cooling ability may be adversely affected.
NOTE: For proper air circulation, and best
cooling and energy consumption
results, maintain a minimum distance
of 2 inches (5,08 cm) from adjacent
items and surfaces.
WARNING
Be careful when you work with the hinge, base grille,
stopper, etc. You may be injured.
Do not put hands or metal sticks into air vents, base
grille or bottom of the refrigerator. You may be injured
or receive an electrical shock.
BASE GRILLE INSTALLATION
To install or replace base grille:
1. Remove the 2 screws from the bottom front part of
refrigerator.
2. Place base grille into position and insert and tighten
screws.
To remove the base grille:
1. Open the doors (Refrigerator and Freezer).
2. Once doors are open, remove screws from base grille
and remove.
3. Reattach screws to the base of refrigerator.
HANDLE REMOVAL
You may have to remove the door handles to move the
refrigerator through a narrow opening. See instructions
below.
2"(5,08 cm)
Mounting
Fasteners
Set
Screw
Allen
Wrench
7
NOTE: To avoid damaging door surfaces when moving
the refrigerator through narrow openings, it is
ALWAYS recommended to remove the doors as
instructed in the next two pages.
• Loosen the set screws with a 3/32” (2,38 mm) Allen
wrench and remove the handle.
NOTE: If the handle mounting fasteners need to be
tightened or moved, use a 1/4” (6,35 mm) Allen
wrench.
HANDLE INSTALLATION
Place the handle on the door by adjusting handle
footprints to fit mounting fasteners and tighten the set
screws with a 3/32” (2,38 mm) Allen wrench .
NOTE: If the handle mounting fasteners need to be
tightened or removed use a 1/4” (6,35 mm) Allen
wrench.
WARNING
ELECTRIC SHOCK HAZARD
• Disconnect electrical supply to the refrigerator before
installing. Failure to do so could result in death or
serious injury.
• Do not put hands, feet or other objects into the air
vents, base grille, or bottom of the refrigerator. You
may be injured or receive an electrical shock.
• Be careful when you work with the hinge, base grille
and stopper. You may be injured. Before removing
the doors, remove the base grille.
REMOVING AND REPLACING REFRIGERATOR
DOORS
Before removing the doors, remove the base grille. See
“Base Grille Installation” for reference.
To remove the right (refrigerator) door:
1. Open the door. Remove the top hinge cover screw (1).
2. Use a flat blade screwdriver to pry back the hooks
(not shown) of the hinge cover (2) from the top of the
refrigerator cabinet. Lift up the cover.
3. Rotate the hinge lever (3) clockwise. Lift the top hinge
(4) free of the hinge lever latch (5).
NOTE: Regardless of hinge lever type, removal process
is the same.
4. Lift the door from the lower hinge pin.
5. Place the door, inside facing up, on a non scratching
surface.
CAUTION: When lifting the hinge free of the latch,
be careful that the door does not fall
forward.
Removing the left (freezer) door with water line
connection:
Pull up the water feed tube while pressing the area (Figure
1) as shown in the figure below.
NOTE: If a tube end is deformed or abraded, trim the
part away. Disconnecting the tube under the door
causes about 0,13 gallons (0,5 liters) water to
flow out. Put a large container at end of tube to
prevent water from draining onto the floor.
1. Open the door. Remove the top hinge cover screw (1).
2. Use a flat blade screwdriver to pry back the hooks
(not shown) of the hinge cover (2) from the top of the
refrigerator cabinet (2). Lift up the cover.
3. Disconnect all the wire harnesses (3).
4. Remove the grounding screw (4).
5. Rotate hinge lever (5) counterclockwise. Lift the top
hinge (6) free of the hinge lever latch (7).
NOTE: Regardless of hinge lever type, removal process
is the same.
CAUTION: When lifting the hinge free of the latch, be
careful that the door does not fall forward.
6. Lift the door from the lower hinge pin being careful to
pull the water lines through the lower hinge pin.
7. Place the door, inside facing up, on a non scratching
surface.
Reinstalling the right (refrigerator) door:
1. Place the door onto the lower hinge pin.
2. Fit top hinge (4) over hinge lever latch (5) into place.
Rotate lever (3) counterclockwise to secure hinge.
NOTE: Regardless of hinge lever type, reinstallation
process is the same.
REFRIGERATOR INSTALLATION
(1 )
(2 )
(3
)
(4 )
(5 )
Type 2
Type 1
(3
)
(4 )
(5 )
Rivet
Figure 1
(1 )
(2 )
(3)
(5)
(6)
(7)
(4)
Type 2
Type 1
(6)
(5)
Rivet
(7)
8
3. Hook tab on switch side of corner under edge of wire
opening in cabinet top. Position cover (2) into place.
Insert and tighten cover screw (1).
Reinstalling the left (freezer) door:
1. Feed the water tubes through the lower hinge pin and
place the door onto the lower hinge pin.
2. Fit top hinge (6) over hinge lever latch (7) and into
place. Rotate lever (5) clockwise to secure hinge.
NOTE: Regardless of hinge lever type, reinstallation
process is the same.
3. Install the grounding screw (4) and connect all the wire
harnesses (3).
4. Hook tab on door switch side of cover (2) under edge
of wire opening in cabinet top. Position cover into place.
Insert and tighten cover screw (1).
5. Reconnect the water tubes by inserting the tubes into
the connectors.
DOOR ALIGNMENT
Remove the base grille before adjusting the doors. See
“Base Grille Installation” for reference. Two methods of
door alignment are available based on the amount of
adjustment needed and installation requirements.
Type 1
Adjusting tool: Flat blade screwdriver. If the freezer
compartment door is lower than the refrigerator
compartment door, level them by inserting a flat blade
screwdriver into the groove of the left leveling leg and
rotating it clockwise.
If the freezer compartment door is higher than the
refrigerator compartment door, level them by inserting a
flat blade screwdriver into the groove of the right leveling
leg and rotating it clockwise.
Type 2
Adjusting tools: 5/16” (8 mm) wrench and 3/4” (19 mm)
wrench.
Using a 3/4” (19 mm) wrench, turn the keeper nut
clockwise to loosen the keeper nut. Using a 5/16” (8
mm) wrench, turn the adjustment hinge pin clockwise
or counterclockwise to level the refrigerator and freezer
door. After setting level door, turn the keeper nut
counterclockwise to tighten.
CAUTION: Do not over tight the door adjustment
screw. The hinge pin can be pulled out.
(Adjustable range of height is a maximum
of 1/2” (1,27 cm)).
AFTER LEVELING THE DOOR HEIGHT
Confirm all legs are in contact with the floor.
REFRIGERATOR INSTALLATION REFRIGERATOR INSTALLATION
(1)
(3)
(4)
(5)
Type 2
Type 1
(3
)
(4 )
(5 )
Rivet
(2 )
(1 )
(2 )
(3)
(5)
(6)
(7)
(4)
Type 2
Type 1
(5)
(6)
(7)
Rivet
Collet
Tube
Insert Line
Left
leveling leg
Height
Height
difference
difference
C
F
C
F
H
C
F
Right
Height
difference
C
F
C
F
H
C
F
Height
difference
leveling leg
Height
difference
Keeper Nut
Adjustment
hinge pin
Wrench
Up
Down
C
F
C
F
H
C
F
Height
difference
9
REFRIGERATOR INSTALLATION
CONNECTING THE WATER LINE
NOTE: Water line installation is needed when the
Automatic Ice maker and/or Water Dispenser
features are available on your product.
BEFORE YOU BEGIN
This water line installation is not warranted by the
refrigerator or ice maker manufacturer or seller. Follow
these instructions carefully to minimize the risk of
expensive water damage. Water hammer (water banging
in the pipes) in house plumbing can cause damage to
refrigerator parts and lead to water leakage or flooding.
Call a qualified plumber to correct water hammer before
installing the water supply line to the refrigerator.
To prevent burns and product damage, do not hook up
the water line to the hot water line.
If you use your refrigerator before connecting the water
line, make sure the ice maker power switch is in the OFF
(O) position. Do not install the ice maker tubing in areas
where temperatures fall below freezing.
When using any electrical device (such as a power drill)
during installation, be sure the device is double insulated
or grounded in a manner to prevent the hazard of electric
shock, or is battery-powered. All installations MUST be in
accordance with local plumbing code requirements.
NOTE: Wear eye protection.
• If a reverse osmosis water filtration system is
connected to your cold water supply, the water line
installation is not warranted by the refrigerator or ice
maker manufacturer or seller. Follow next instruction
carefully to minimize the risk of expensive water
damage.
• If a reverse osmosis water filtration system is
connected to your cold water supply, the water pressure
to the reverse osmosis system needs to be a minimum
of40to60PSI(2,8kg•f/cm²~4,2kg•f/cm²,less
than2~3sectollacupof7oz.capacity).
If the water pressure from the reverse osmosis system is
lessthan21PSI(1,5kg•f/cm²,morethan4sectolla
cup of 7 oz. capacity):
•Checktoseewhetherthesedimentlterinthereverse
osmosis system is blocked. Replace the filter if necessary.
•Allowthestoragetankonthereverseosmosissystemto
refill after heavy usage.
•Iftheissueaboutwaterpressurefromreverseosmosis
remains, call a licensed, qualified plumber.
WHAT YOU WILL NEED
• Copper Tubing, 1/4” (6,35 mm) outer diameter
to connect the refrigerator to the water supply.
Be sure both ends of the tubing are cut
square.
To determine how much tubing you need, measure
the distance from the water valve on the back of the
refrigerator to the water supply pipe. Then add 8 feet
(2,4 m). Be sure there is sufficient extra tubing (about
8 feet [2,4 m] coiled into 3 turns of about 10” [25 cm]
diameter) to allow the refrigerator to move out from the
wall after installation.
Be sure that the kit you select allows at least 8 feet
(2,4 m) as described above.
• A cold water supply. The water pressure MUST be
between 20 and 120 PSI (1,4 bar and 8,2 bar) on
models without a water filter and between 40 and 120
PSI (2,8 bar and 8,2 bar) on models with a water filter.
• Power drill.
• 1/2” (12,7 mm) or Adjustable Wrench.
• Flat head and Phillips screwdrivers.
• Two 1/4” (6,35 mm) outer
diameter compression nuts
and 2 ferrules (sleeves) to
connect the copper tubing
to the shutoff valve and the
refrigerator water valve.
If your existing copper water line has a
flared fitting at the end, you will need
an adapter (available at plumbing
supply stores) to connect the water
line to the refrigerator OR you can cut
off the flared fitting with a tube cutter and then use a
compression fitting.
• Shutoff valve to connect to
the cold water line. The shutoff
valve should have a water
inlet with a minimum inside
diameter of 5/32” (3,96 mm)
at the point of connection to
the COLD WATER LINE. Saddle-type shutoff valves are
included in many water supply kits. Before purchasing,
make sure a saddle-type valve complies with your local
plumbing codes.
INSTALLATION INSTRUCTIONS
WARNING: Connect to potable water supply only.
1. SHUTOFF THE MAIN WATER SUPPLY
Turn on the nearest faucet to relieve the pressure on the
line.
2. CHOOSE THE VALVE LOCATION
Choose a location for the valve that is
easily accessible. It is best to connect into
the side of a vertical water pipe. When it
is necessary to connect into a horizontal
water pipe, make the connection to the
top or side, rather than at the bottom, to
avoid drawing off any sediment from the
water pipe.
10
3. DRILL THE HOLE FOR THE VALVE
Drill a 1/4” (6,35 mm) hole in
the water pipe using a sharp bit.
Remove any burrs resulting from
drilling the hole in the pipe. Take
care not to allow water to drain into
the drill. Failure to drill a 1/4” (6,35
mm) hole may result in reduced
ice production or smaller cubes.
NOTE: Licensed plumbers MUST use only cooper tubing
NDA tubing #49595 or 49499 or Cross Link
Polyethylene (PEX) tubing.
4. FASTEN THE SHUTOFF VALVE
Fasten the shutoff valve to the cold water pipe with the
pipe clamp.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves are
illegal and use is not permitted in Massachusetts. Consult
with your licensed plumber.
5. TIGHTEN THE PIPE CLAMP
Tighten the clamp screws until the sealing washer begins
to swell.
NOTE: Do not overtighten or you may crush the tubing.
6. ROUTE THE TUBING
Route the tubing between the cold water line and the
refrigerator. Route the tubing through a hole drilled in
the wall or floor (behind the refrigerator or adjacent base
cabinet) as close to the wall as possible.
NOTE: Be sure there is sufficient extra tubing [about
8 feet (2,4 m) coiled into 3 turns of about 10”
(25 cm) diameter] to allow the refrigerator to
move out from the wall after installation.
7. CONNECT THE TUBING TO THE VALVE
Place the compression nut and ferrule (sleeve) for copper
tubing onto the end of the tubing and connect it to the
shutoff valve. Make sure the tubing is fully inserted into
the valve. Tighten the compression nut securely.
NOTE: Commonwealth of Massachusetts Plumbing
Codes 248CMR shall be adhered to. Saddle valves are
illegal and use is not permitted in Massachusetts. Consult
with your licensed plumber.
8. FLUSH OUT THE TUBING
Turn the main water supply on and
flush out the tubing until the water is
clear. Shut the water off at the water
valve after about one quart (1 L) of
water has been flushed through the
tubing.
9. CONNECT THE TUBING TO THE
REFRIGERATOR
NOTES:
• Before making the connection to the refrigerator, be
sure the refrigerator power cord is not plugged into the
wall outlet.
• If your refrigerator does not have a water filter, we
recommend installing one. If your water supply has
sand or particles that could clog the screen of the
refrigerator’s water valve, install the filter in the water
line near the refrigerator.
• Do not uses old hoses; only use new hoses provided by
the manufacturer.
1. Remove the plastic flexible cap from the refrigerator
connection.
2. Place the compression nut and ferrule (sleeve) onto the
end of the tubing. (See figure 1).
3. Insert the end of the tubing into the connection as
far as possible. While holding the tubing, tighten the
fitting.
CAUTION: Check to make sure that leaks are not
occurring in the water line.
REFRIGERATOR INSTALLATION REFRIGERATOR INSTALLATION
Pipe Clamp
Saddle-Type
Shutoff Valve
Vertical Cold
Water Pipe
Pipe Clamp
Clamp Screw
Washer
Inlet End
Saddle-Type
Shutoff Valve
Packing
Nut
Outlet
Valve
Compression
Nut
Ferrule
(sleeve)
11
REFRIGERATOR INSTALLATION
Fasten the tubing into the tubing clamp attached to the
back of the refrigerator. First, loosen the screw fastening
the clamp. Next, insert the tubing in the groove. Finally,
re-fasten the screw.
10. PLUG IN THE REFRIGERATOR
Arrange the coil of tubing so that
it does not vibrate against the
back of the refrigerator or against
the wall. Push the refrigerator
back to the wall.
11. START THE ICE MAKER
Set the ice maker power switch to the ON (I) position.
The ice maker will not begin to operate until it reaches
its operating temperature of 15 °F (-9 °C) or below. It will
then begin operation automatically if the ice maker power
switch is in the ON (I) position.
1/4” (6,35 mm) Tubing
Refrigerator
Connection
1/4” (6,35 mm)
Compression
Nut
Ferrule
(sleeve)
Back of refrigerator
Figure 1
Tubing Clamp
12
REFRIGERATOR FEATURES USING YOUR REFRIGERATOR
Use this page to become more familiar with the parts and features.
NOTE: This guide covers several different models. The refrigerator you have purchased may have some or all of the
items listed below. The locations of the features shown below may not match your model.
Freezer Door Rack
Automatic Ice maker
The ice is produced in the ice maker and sent to the
dispenser.
Freezer Lamp (LED)
Freezer Shelf
Drawer
Base Grille
Dairy Corner
For storage of dairy products such as butter and cheese.
Refrigerator Lamp (LED)
Water Filter
Refrigerator Shelf
Snack Pan *
For storage of meat or fresh food.
Refrigerator Door Rack
Vegetable Drawer
* In some models
A
B
C
F
G
E
D
H
I
J
K
L
M
13
USING YOUR REFRIGERATOR
ENSURING PROPER AIR CIRCULATION
In order to ensure proper temperatures, air MUST flow
between the refrigerator and freezer sections.
• Cool air enters the freezer through the vents located
at the top of the compartment and exits through the
vents located behind the freezer drawers.
• Cool air from the freezer section enters the fresh
food section through vents located at the top of the
compartment. The air moves down throughout the
compartment and exits through the vents located
behind the crisper drawers.
• Do not block any of these vents with food packages.
If the vents are blocked, airflow will be interrupted and
temperature and moisture problems may occur.
IMPORTANT: Because air circulates between both
sections, any odors formed in one section will transfer to
the other.
You MUST thoroughly clean both sections to eliminate
odors. To prevent odor transfer and dried out food, wrap
or cover foods tightly. (See the “Food Storage Guide”
section for details.)
NOTE: If you close the
refrigerator door, you may see
the freezer door open and close
again due to pressure from
internal air flow.
PRIOR TO USE
1. Clean your refrigerator thoroughly and wipe off dust
accumulated during shipping.
2. Install accessories such as ice cube bin, drawers,
shelves, etc., in their proper places. They are packed
together to prevent possible damage during shipment.
3. Let your refrigerator run for at least 2 or 3 hours before
putting food in it. Check the flow of cold air in the
freezer compartment to ensure proper cooling. Your
refrigerator is now ready for use.
CONTROL PANEL FEATURES
Press the button for the desire function to review and
select other settings.
REFRIGERATOR AND FREEZER CONTROLS
Initially set the refrigerator and freezer controls to
the recommended (middle) settings by pressing
REFRIGERATOR Graphic and FREEZER Graphic.
NOTE: When changing control settings, wait 24 hours
before making additional adjustments. After 24
hours, adjust the compartments temperatures
as desired . The more lit bars, the colder the
refrigerator and freezer will be.
Display Off Mode
The display lights up and stays lit when the refrigerator is
plugged in for 60 seconds. After the display lights all off
except the dispenser icon selected (CRUSH, WATER or
CUBE) and the display only lights when door is opened
or display button is pressed. Display turn off 20 seconds
after door is closed or display button pressed. You can
change the display always ON pressing “FREEZER” and
“ICE PLUS” buttons at the same time for 5 seconds. A
tone will sound indicating that the display is ON (Display
Off Mode Deactivate). Activate the Display Off Mode in
same manner as deactivation.
ICE TYPE
You can select water or ice.
Select Water, Crushed Ice or Cubed Ice by pressing the
ICE TYPE button to the selection desired. The Water,
Crushed Ice or Cubed Ice icon will light up to indicate
selection.
Light up the cubed ice lamp by pressing the
selection button. The dot will be illuminated.
Light up the water lamp by pressing the selection
button. The dot will be illuminated.
Light up the crushed ice lamp by pressing the
selection button. The dot will be illuminated.
14
USING YOUR REFRIGERATOR USING YOUR REFRIGERATOR
To dispense water or ice, gently push your cup against the
dispenser pad.
NOTE: Hold your cup in place for a couple of seconds
after dispensing ice or water so the last few drops
go in your cup instead of on the floor.
DOOR ALARM
When either refrigerator or freezer door is left open for
more than 60 seconds, an alarm will sound 5 times at
thirty-second intervals to let you know the door is open.
The alarm will repeat every 30 seconds until all doors
are completely closed. Please contact the local service
center if warning tone continues to sound even after
closing the door.
FILTER
(Filter Replacement Cycle)
There is an indicator light for the water filter cartridge
on the dispenser that will blink to indicate it is time to
change the water filter. Water filters usually need to be
replaced once every six months. After replacing the filter,
press and hold the Filter Reset button for 3 seconds to
turn off the filter status light.
LOCK
The Lock button deactivates the temperature controls
and dispenser functions. Press and hold this button for 3
seconds or until the Lock indicator light is lit. To disable
the Lock function, press and hold the filter button for
seconds or until the Lock indicator light is off.
ICE PLUS
Press this button once to activate the increased ice
making function. The ICE PLUS icon on the display panel
will illuminate when activated. The Ice Plus function runs
the freezer compartment at the coldest settings for a
24 hour period to increase ice making. Press the button
again to cancel the Ice Plus function.
ADJUSTING CONTROL SETTINGS
Give the refrigerator time to cool down completely
before making final adjustments. It is best to wait 24
hours before doing this. The initial settings mentioned
in “Control Panel Features” section should be correct for
normal household refrigerator use.
The refrigerator control functions as the thermostat for
the entire appliance (refrigerator and freezer sections).
The colder the setting, compressor will the longer the
run to keep the temperature colder. The freezer control
adjusts the cold air flow from the freezer to the refrigerator.
Setting the freezer control to a lower temperature keeps
more cold air in the freezer compartment to make it
colder.
If you need to adjust temperatures in the refrigerator or
freezer, start by adjusting the refrigerator and allow 24
hours for the temperature to stabilize. If it is too warm or
too cold, then adjust the freezer control. Use the settings
listed in the chart below as a guide. Always remember to
wait at least 24 hours between adjustments.
CONDITION/REASON: RECOMMENDED
ADJUSTMENT:
REFRIGERATOR section
is too warm
•Opening the door often
•Adding a large amount
of food
•Room temperature is
very warm
Adjust the
REFRIGERATOR setting
to the next highest
number and wait 24
hours, then check.
FREEZER section is too
warm/ ice is made too
slowly
•Opening the door often
•Adding a large amount
of food
•Room temperature is
very low (not cycling
often enough)
•Using ice frequently
•Air vents blocked by
objects
Adjust the FREEZER
setting to the next
highest number and wait
24 hours, then check.
Remove any objects
blocking air flow.
REFRIGERATOR section
is too cold
•Controls not set
correctly for your
conditions
Adjust the
REFRIGERATOR setting
to the next lowest number
and wait 24 hours, then
check.
FREEZER section is too
cold
•Controls not set
correctly for your
conditions
Adjust the FREEZER
setting to the next lowest
number and wait 24
hours, then check.
ICE MAKER OPERATION
WARNING
PERSONAL INJURY HAZARD
Avoid contact with the moving parts of the ejector
mechanism, or with the heating element that releases
the cubes. DO NOT place fingers or hands on the
automatic ice making mechanism while the refrigerator
is plugged in.
A newly-installed refrigerator may take 12 to 24 hours to
begin making ice.
Power Switch
ON / OFF
Feeler Arm
15
USING YOUR REFRIGERATOR
The ice maker will produce 12 cubes per cycle,
approximately 140-150 cubes in a 24 hour period,
depending on freezer compartment temperature, room
temperature, number of door openings and other
operating conditions.
If the refrigerator is used before the water connection is
made to the ice maker, set the power switch to OFF (O).
Throw away the first few batches of ice to allow the water
line to clear.
Be sure nothing interferes with the sweep of the feeler
arm. When the bin fills to the level of the feeler arm, the
ice maker will stop producing ice.
It is normal for several cubes to be stuck together. If ice
is not used frequently, old ice cubes will become cloudy,
taste stale and shrink.
FOOD STORAGE GUIDE
Wrap or store food in the refrigerator in airtight and
moisture-proof material unless otherwise noted. This
prevents food odor and taste transfer throughout the
refrigerator. For dated products, check date code to
ensure freshness.
ITEMS HOW TO STORE
Storing Fresh Food Wrap or store food in the
refrigerator in airtight and
moisture-proof material unless
otherwise noted. This prevents
food odor and taste transfer
throughout the refrigerator. For
dated products, check date code
to ensure freshness.
Butter or
margarine
Store opened butter in a covered
dish or in a closed compartment.
When storing a larger quantity,
wrap in freezer packing and
freeze.
Cheese Store in original packaging until
you are ready to use it. Once
opened, tightly rewrap with plastic
wrap or aluminum foil.
Vegetables with
skins (carrots,
peppers)
Place in bags or plastic containers
inside the crisper.
Fruit Wash and let dry; store in plastic
bags in the refrigerator. Do not
wash or pit berries until you are
ready to eat them. Berries should
be selected and kept in their
original packaging (if there is any)
or in a paper bag closed halfway
and set on a shelf.
Leafy Vegetables Remove original packaging and
trim any dirty or discolored parts.
Wash in cold water and drain.
Place in a plastic bag or plastic
container and store in the crisper.
ITEMS HOW TO STORE
Fish Consume fish or seafood the
same day purchased.
Chef Fresh Store any meat in original airtight,
moisture-proof packaging.
Rewrap if necessary.
Leftovers Cover leftovers with plastic
wrap or aluminum foil. Plastic
containers with airtight lids can
also be used.
STORING FROZEN FOOD
NOTE: For further information about preparing food for
freezing or food storage times, check a freezer
guide or a reliable cookbook.
Packaging
Successful freezing depends on correct packaging.
When you close and seal the package, it must not allow
air or moisture in or out. If it does, you could have food
odor and taste transfer throughout the refrigerator and
also dry out frozen food.
Packaging Recommendations:
• Rigid plastic containers with “tight-fitting lids”.
• Straight-sided canning/freezing jars.
• Heavy-duty aluminum foil.
• Plastic-coated paper.
• Non-permeable plastic wraps.
• Specified freezer-grade self-sealing plastic bags.
Follow package or container instructions for proper
freezing methods.
Do not use:
• Bread wrappers
• Containers without tight lids
• Wax paper or wax-coated freezer wrap
• Thin, semi-permeable wrap
CAUTION: Do not keep beverage cans or plastic food
containers in the freezer compartment.
They may burst if they freeze.
Freezing
Your freezer will not quick-freeze any large quantity of
food. Do not put more unfrozen food into the freezer than
will freeze within 24 hours [no more than 2 to 3 lbs of
food per cubic foot (0,9 to 1,35 kg per cubic meter) of
freezer space]. Leave enough space in the freezer for air
to circulate around packages. Be careful to leave enough
room at the front so the door can close tightly.
Food storage times will vary according to the quality and
type of food, the type of packaging or wrap used (airtight
and moisture-proof) and the storage temperature. Ice
crystals inside a sealed package are normal. This simply
means that moisture in the food and air inside the
package have condensed, creating ice crystals.
NOTE: Allow hot foods to cool at room temperature for
30 minutes, then package and freeze. Cooling
hot foods before freezing saves energy.
16
WATER AND ICE DISPENSER
Your refrigerator has a mechanism that dispatch cool
water and ice cubes without open the door.
• Tray can be easily removed by pressing and pulling it.
• First push the tray in the area with the word ‘PUSH’,
then place your finger in the center hole and upwards,
finally takes out the tray.
WARNING
Do not put your hands into the water
& ice dispenser opening. Doing so
may cause an injury to your hand.
CAUTION
When opening the container with
the small opening, use it near the
opening of the water or ice dispenser
as close as possible.
ICE STORAGE BIN
The ice bin stores the ice cubes made by the ice maker. If
you need to remove the ice storage bin, do so as follows:
NOTE: Use both hands to remove the ice bin to avoid
dropping it. If the ice bin does not slide into place
easily, twist the drive device slightly.
• Hold the ice storage bin and pull it out while slightly
lifting it shown in the figure.
• To assemble the ice storage bin, push it while slightly
lifting it .
• Make sure it is fully engaged into the auger drive .
ICE MAKER COVER
If you need access to the ice maker, follow these steps:
• Lift the ice shelf and pull it out as shown in the
figure below.
DOOR RACK AND SUPPORT
Your refrigerator and freezer features racks which can
easily be arranged for packaged products.
• Lift the door rack holding both sides and pull it out
in direction.
SNACK PAN (in some models)
• To remove the snack pan cover, pull out the snack pan
compartment a bit to the front , then lift the front part
of the snack pan compartment later raises a little the
snack pan compartment until it leaves the top of the
shelf as shown in , and take it out.
USING YOUR REFRIGERATOR USING YOUR REFRIGERATOR
1
2
4
3
5
2
1
2
1
2
1
17
USING YOUR REFRIGERATOR
CRISPER AND CRISPER COVER
The crisper allows for better conservation of fruits and
vegetables.
• To remove the crisper compartment cover, pull out the
crisper compartment a bit to the front , lift the front
part of the cover as shown in , and take it out .
• To remove the crisper compartment, pull the crisper
compartment to the front until it stops. Then slightly
lift the crisper compartment while pulling it out .
CAUTION
When removing the crisper compartment you will see
the water tank. Do not remove it, or water leakage
may result. The water tank is not a removable part.
HUMIDITY CONTROLS
You can control the amount of humidity in the moisture
sealed crispers. Adjust the control to any setting between
“HIGH” and “LOW”.
“HIGH”: Keeps moist air in the crisper for best storage of
fresh, leafy vegetables.
“LOW”: Keeps moist air out of the crisper for best storage
of fruits or vegetables with skins.
REFRIGERATOR SHELVES
CAUTION
Make sure to keep shelf horizontal while removing;
otherwise it may drop.
The refrigerator compartment shelf is adjustable so
that you can place it at a height according to space
requirement of foods.
Sliding out Shelf:
Pull the shelf towards you , then lift both front and
rear while taking it out .
CAUTION
Be careful when pulling out the shelf. If you apply
too much force, it may hit the refrigerator door
and damage it or you could hurt yourself.
Fixed Shelf:
• Lightly lift up the front part of the shelf to pull it
towards you ,then take it out while lifting the rear part
of shelf .
FREEZER SHELF
To assemble or disassemble the freezer shelf, follow the
next steps:
• Lift the left part of the shelf a bit. Lift it to the direction
, push the right part to the direction and take it out.
Tank
Door
1
2
4
3
5
3
2
1
2
1
3
2
1
3
3
2
1
1
2
18
WATER FILTER
Filter Reset: When the filter icon turns on, you
have to change the water filter. Press the Filter
button for 3 seconds to turn the icon off.
Before removing or installing water filter:
• IMPORTANT: Turn off household water supply.
• Take out the top shelf and move it to the lowest level.
Removing the Water Filter
• Remove old filter by turning it counterclockwise a
quarter turn and pulling it down. The substitute cap
must be retained for the future. If the filter is removed
and not replaced, it is necessary to reinstall the
substitute cap to prevent water leaks from the filter
housing.
Installing the Water Filter
• Remove the red cap from the filter.
• Hold the filter with the unlock symbol facing
towards you as shown in the figure below. Insert the
filter into the filter receptacle on the right side of the
refrigerator compartment.
• Push the water filter up into the filter receptacle and
rotate it clockwise to lock it into place. Once installed
correctly, the lock symbol should be facing you
and you should not be able to rotate the filter clockwise
anymore.
NOTE: After installation, if you notice that the lock symbol
is not facing you or you can continue to rotate
the filter clockwise; remove the filter and repeat
installation to prevent water leaks.
After installing the Water Filter
• Replace the shelf to the initial position.
• After installing filter, turn on household water supply.
• Dispense 2,5 gallons (9,46 liters) of water to purge the
system, depressing and releasing the dispenser pad in
cycles of 30 seconds ON and 60 seconds OFF. Open
the refrigerator door and check the shelf area for water
leaks.
To purchase or replace water filters, call your Service
Center. Refer to the Warranty Card to obtain the telephone
number of the Service Center near you and ask for part
no. 5231JA2002A or ADQ72910901.
FILTER FILTER
19
FILTER
Performance Data Sheet
Models Number 5231JA2002A-S
Use with replacement cartridge 5231JA2002A
This system has been tested according to NSF/ANSI Standards 42 for the reduction of the substances listed below.
The concentration of the indicated substances in water entering the system was reduced to a concentration less than
or equal to the permissible limit for water leaving the system as specified in NSF/ANSI 42.
System tested and certified by NSF International against NSF/ANSI Standard 42 for the reduction
of Chlorine Taste and Odor and Nominal Particulate Class III.
Capacity: 500 gal (1,892 L)
Substance
Average
Influent
Concentration
Influent Challenge
Concentration.
Units apply to
each row
Avg. Product
Water
Concentration
Average
%
Reduction
NSF % reduction
req. or Max
permissible
product water
concentration
Nominal Particulate
Class I Particle size: ›0.5 to ‹1 um
24,333
At least 10,000
particles/ml
915 96 ≥ 85%
Chlorine taste and odor
Class III
1,9 2.0 mg/L ± 10% 0,07 96,4 ≥ 50%
Note that while the testing was performed under standard laboratory conditions, actual performance may vary.
Application Guidelines / Water Supply Parameters
Service flow 0,5 gpm (1,89 lpm)
Water pressure 20 - 125 psi (138 - 862 kPa)
Water temperature 33 ºF - 100 ºF (0,6 ºC - 38 ºC)
WARNING
To reduce the risk associated with ingestion of
contaminants due to use with water that is micro
biologically unsafe or of unknown quality. Do not
use with water that is micro biologically unsafe or of
unknown quality without adequate disinfection before
or after the system.
Systems must be installed and operated in accordance
with manufacturer’s recommended procedures and
guidelines.
CAUTION
To reduce the risk of property damage due to water
leakage:
• Read and follow Use instructions before installation
and use of this system.
• Install on COLD water lines only. Comply with all
state and local plumbing codes.
• Install a pressure limiting device and water hammer
arrester for inlet water pressures exceeding 80
psi (552 kPa). Refer to Uniform Plumbing Code,
Sections 608.2 and 609.10.
• Never install or operate where inlet water pressure
may exceed 120 psi (827 kPa).
• Protect filter from freezing. Remove filter in
temperatures below 33 °F (0.6 °C).
• Replace cartridge at specified service interval.
Cartridge MUST be replaced at least every 6 months.
To purchase or replace water filters call your Service
Center. Refer to the Warranty Card to obtain the
telephone number of the Service Center near you and
ask for part no. 5231JA2002A or ADQ72910901.
*
20
CARE AND CLEANING
WARNING
EXPLOSION HAZARD
Use non-flammable cleaner. Failure to do so can result
in death, explosion, or fire.
Both the refrigerator and freezer sections defrost
automatically. However, clean both sections about once
a month to prevent odors. Wipe up spills immediately.
GENERAL CLEANING TIPS
•Unplug refrigerator or disconnect power.
•Remove all removable parts, such as shelves, crispers,
etc. Refer to sections in “Using Your Refrigerator” for
removal instructions.
•Use a clean sponge or soft cloth and a mild detergent
in warm water. Do not use abrasive or harsh cleaners.
•Hand wash, rinse and dry all surfaces thoroughly.
•Plug in refrigerator or reconnect power.
OUTSIDE
Waxing external painted metal surfaces helps provide
rust protection. Do not wax plastic parts. Wax painted
metal surfaces at least twice a year using appliance wax
(or auto paste wax). Apply wax with a clean, soft cloth.
Do not use wax on stainless steel exteriors. Use a product
specially designed for polishing stainless steel appliances,
or clean with a soft cloth or clean sponge and a mild
detergent dissolved in warm water. Dry thoroughly with a
soft cloth.
NOTE: Avoid door surface contact with chemical
products that contain Phosphate or Chlorine,
such as degraders, detergents (containing TSP)
and bleaches.
INSIDE WALLS
NOTE: Allow freezer to warm up so cloth will not stick.
To help remove odors, you can wash the inside of the
refrigerator with a mixture of baking soda and warm
water. Mix 2 tablespoons baking soda to 1 quart of water
(26 g soda to 1 liter water.) Be sure the baking soda is
completely dissolved so it does not scratch the surfaces
of the refrigerator.
DOOR LINERS AND GASKETS
Do not use cleaning waxes, concentrated detergent,
bleaches, or cleaners containing petroleum on plastic
refrigerator parts. Use a clean sponge or soft cloth and
a mild detergent in warm water. Wash, rinse and dry all
surfaces thoroughly.
PLASTIC PARTS (covers and panels)
Do not use window sprays, abrasive cleaners, or flammable
fluids. These can scratch or damage the material. Use a
clean sponge or soft cloth and a mild detergent in warm
water. Wash, rinse and dry all surfaces thoroughly.
BACK COVER
WARNING
ELECTRICAL SHOCK HAZARD
Before you begin, either unplug the refrigerator or turn
off power at the circuit breaker or fuse box. Failure to
do so could result in death or serious injury
NOTE: Back Cover should only be removed by a qualified
technician.
Clean the vents on the back cover.
Use a vacuum cleaner with the
brush attachment, at least twice
a year to keep your refrigerator
working efficiently.
LIGHT (LED) REPLACEMENT
NOTE: Do not remove the LED, it is only to be removed
by a qualified technician.
POWER INTERRUPTIONS
1. If the power will be out for 24 hours or less, keep all
refrigerator doors closed to help foods stay cold and
frozen.
2. If the power will be out for more than 24 hours:
a) Remove all frozen food and store it in a frozen food
locker.
OR
b) Place 2 lbs. (1 kg) of dry ice in the freezer for every
cubic foot (28 L) of freezer space. This will keep the food
frozen for two to four days. While handling dry ice, wear
gloves to protect your hands from frostbite.
WARNING
SUFFOCATION HAZARD
When using dry ice, provide adequate ventilation, Dry ice
is frozen carbon dioxide (CO
2
). When it vaporizes, it can
displace oxygen, causing dizziness, light-headedness,
unconsciousness and death by suffocation. Open a
window and do not breathe the vapors.
OR
c) If neither a food locker nor dry ice is available, consume
or dispose of food at once.
REMEMBER: In a power failure, a full freezer stays cold
longer than a partially filled one. If you see that food
contains ice crystals, it may be affected. If the condition
of the food is poor, or if you feel it is unsafe, dispose of it.
BACK
COVER
21
CARE AND CLEANING CARE AND CLEANING
WARNING
DO NOT refreeze frozen foods which have thawed
completely. The United States Department of
Agriculture in Home and Garden Bulletin No. 69 says:
...You may safely refreeze frozen foods that have thawed
if they still contain ice crystals or if they are still cold-
below 40 °F (4 °C). ...Thawed ground meats, poultry
or fish that have any off-odor or off-color should not
be frozen and should not be eaten. Thawed ice cream
should be discarded.
If the odor or color of any food is poor or questionable,
dispose of it. The food may be dangerous to eat. Even
partial thawing and refreezing reduces the eating
quality of foods, particularly fruits, vegetables and
prepared foods.
The eating quality of red meats is affected less than
that of many other foods. Use refrozen foods as soon
as possible to save as much of their quality as you can.
WHEN YOU GO ON VACATION
If you choose to leave the refrigerator ON while you
are away, follow these steps to prepare your refrigerator
before you leave.
1. Use up any perishables and freeze other items.
2. Empty the ice bin.
3. Turn OFF the Ice maker. NOTE: If the ambient
temperature will drop below freezing, have a quailed
service technician drain the water supply system (on
some models) to prevent serious property damage
due to possible flooding from ruptured water lines or
connections.
If you choose to turn the refrigerator OFF before you
leave, follow these steps:
1. Remove all food from the refrigerator and empty ice
bin.
2. Unplug refrigerator.
3. Clean refrigerator, wipe, and dry well.
4. Tape rubber or wood blocks to the tops of both doors
to prop them open far enough for air to get in. This
stops odor and mold from building up.
WHEN YOU MOVE
When you are moving your refrigerator to a new home,
follow these steps to prepare it for the move.
1. Remove all food from the refrigerator and pack all
frozen food in dry ice.
2. Unplug refrigerator.
3. Clean refrigerator, wipe, and dry well.
4. Empty water from the defrost pan.
5. Clean, wipe and dry thoroughly.
6. Take out all removable parts, wrap them well and tape
together so they don’t shift and rattle during the move.
Refer to sections in Using your Refrigerator for removal
instructions.
7. Depending on the model, raise the front of the
refrigerator so it rolls more easily OR screw in the
leveling legs all the way so they don’t scrape the floor.
See the “Door Alignment” section.
8. Tape the doors shut and tape the power cord to the
refrigerator cabinet.
When you get to your new home, put everything back and
refer to the “Refrigerator Installation” section for setup
instructions.
WHEN YOU SHOULD SET THE ICE MAKER
POWER SWITCH TO OFF (O)
• When the water supply will be shut off for several hours.
• When the ice storage bin is removed for more than a
minute or two.
• When the refrigerator will not be used for several days.
NORMAL SOUNDS YOU MAY HEAR
• The ice maker water valve will buzz as the ice maker
fills with water. If the power switch is in the ON position,
it will buzz even if it has not yet been hooked up to
water. To stop the buzzing, move the power switch to
OFF position.
NOTE: Keep the power switch in the ON position before
the water line is connected can damage the ice
maker.
• You will hear the sound of cubes dropping into the bin
and water running in the pipes as the ice maker refills.
22
TROUBLESHOOTING GUIDE
UNDERSTANDING SOUNDS YOU MAY HEAR
Your new refrigerator may make sounds that your old
one did not make. Because the sounds are new to you,
you might be concerned about them. Most of the new
sounds are normal. Hard surfaces, like the floor, walls
and cabinets, can make the sounds seem louder than
they actually are. The following list describes the kinds of
sounds and what may be making them.
• The defrost timer will click when the automatic defrost
cycle begins and ends. The thermostat control (or
refrigerator control, depending on the model) will also
click when cycling on and off.
• Rattling noises may come from the flow of refrigerant,
the water line, or items stored on top of the refrigerator.
• Your refrigerator is designed to run more efficiently
to keep your food items at the desired temperature.
The high efficiency compressor may cause your new
refrigerator to run longer than your old one, and you
may hear a pulsating or high-pitched sound.
• You may hear the evaporator fan motor circulating the
air through the refrigerator and freezer compartments.
• As each cycle ends, you may hear a gurgling sound
due to the refrigerant flowing in your refrigerator.
• Contraction and expansion of the inside walls may
cause a popping noise.
• Water dripping on the defrost heater during a defrost
cycle may cause a sizzling sound.
• You may hear air being forced over the condenser by
the condenser fan.
• You may hear water running into the drain pan during
the defrost cycle.
Problem Possible Causes Solutions
REFRIGERATOR
DOES NOT
OPERATE
•The power supply cord is unplugged.
•A household fuse has blown or
circuit breaker tripped.
•The refrigerator control is set to the
OFF position.
•Refrigerator is in the defrost cycle.
•Firmly plug the cord into a live outlet with proper
voltage.
•Replace the fuse or reset the circuit breaker.
•Refer to the “Control Panel Features” section.
•Wait about 30 minutes for defrost cycle to end.
VIBRATION OR
RATTLING NOISE
•The refrigerator is not resting solidly
on the floor.
•Floor is weak or uneven or leveling legs need
adjusting. See “Door Alignment” Section.
LED (LAMP) DO
NOT WORK
•The power supply cord is unplugged.
•LED Light has burned out.
•Firmly plug the cord into a live outlet with proper
voltage.
•See the “Light (LED) Replacement” section.
COMPRESSOR
MOTOR SEEMS TO
RUN TOO MUCH
•The refrigerator that was replaced
was an older model.
•The room temperature is hotter than
normal.
•The refrigerator was recently
plugged in and the refrigerator
control was set correctly.
•The door is opened often or a large
amount has just been added.
•The refrigerator control was not
set correctly for the surrounding
conditions.
•Modern refrigerators with more storage space
require more operating time.
•The motor will run longer under warm conditions.
At normal room temperatures, expect your motor
to run about 40% to 80% of the time. Under
warmer conditions, expect it to run even more
often.
•The refrigerator will take up to 24 hours to cool
completely.
•Adding food and opening the door warms the
refrigerator. It is normal for the refrigerator to
run longer in order to conserve energy, try to get
everything you need out of the refrigerator at once,
keep food organized so it is easy to find and close
the door as soon as the food is removed. See the
“Food Storage Guide” section.
•See the “Adjusting Control Settings” Section.
23
TROUBLESHOOTING GUIDE TROUBLESHOOTING GUIDE
Problem Possible Causes Solutions
COMPRESSOR
MOTOR SEEMS TO
RUN TOO MUCH
•The doors are not closed completely.
•The condenser coils are dirty.
•Push the doors firmly shut. If they will not shut all
the way, see Doors will not close completely below.
•This prevents air transfer and makes the motor
work harder. Clean the condenser coils. Refer to
the “Care and Cleaning” section.
DOORS WILL NOT
CLOSE
COMPLETELY
•The refrigerator is not level.
•Food packages are blocking the
door open.
•The ice bin, crisper cover, pans,
shelves, door bins or baskets are out
of position.
•The gaskets are sticking.
•The refrigerator wobbles or seems
unstable.
•The doors were removed during
product installation and not properly
replaced.
•See the “Refrigerator Installation” and “Door
Alignment” sections to level refrigerator.
•Rearrange food containers to clear door and door
shelves.
•Push bins all the way in and put crisper cover, pans,
shelves and baskets into their correct positions.
See the “Using your Refrigerator” Section.
•Clean gaskets and the surface that they touch.
Rub a thin coat of paraffin wax on the gaskets after
cleaning.
•Level the refrigerator. Refer to the “Door
Alignment” section.
• Remove and replace the doors according to the
“Removing and Replacing Refrigerator Doors”
section or call qualified service technician.
THE DOORS ARE
DIFFICULT TO
OPEN
•The gaskets are dirty or sticky.
•The door is reopened within a short
time after having been opened.
•Clean gaskets and the surfaces that they touch.
Rub a thin coat of appliance polish or kitchen wax
on the gaskets after cleaning.
•When you open the door, warmer air enters the
refrigerator. As the warm air cools, it can create a
vacuum. If the door is hard to open, wait 5 minutes
to allow the air pressure to equalize, then see if it
opens more easily.
TEMPERATURE IS
TOO WARM OR
THERE IS
INTERIOR
MOISTURE
BUILDUP
•The doors are opened often.
•The control is not set correctly for
the surrounding conditions.
•A large amount of food has just
been added to the refrigerator or
freezer.
•The food is not packaged correctly.
•The doors are not closing completely.
•The weather is humid.
•A self-defrost cycle was completed.
•The air vents are blocked. Cold air
circulates from the freezer to the
fresh food section and back again
through air vents in the wall dividing
the two sections.
•When the door is opened, warm humid air is
allowed into the refrigerator. The more the door is
opened, the faster the humidity builds up, and the
more warm air the refrigerator must cool. In order
to keep the refrigerator cool, try to get everything
you need out of the refrigerator at once, keep food
organized so it is easy to find and close the door
as soon as the food is removed.
•Refer to the “Control Panel Features”. Wait 24
hours for temperatures to stabilize or even out. If
the temperature is too cold or too warm, adjust the
setting one level at a time.
•Adding food warms the refrigerator. It can take a
few hours for the refrigerator to return to normal
temperature.
•Wrap food tightly and wipe off damp containers
prior to storing in the refrigerator to avoid moisture
accumulation. If necessary, repackage food
according to the guidelines in the “Food Storage
Guide” section.
•See “Doors will not close completely”.
•In humid weather, air carries moisture into
refrigerator when doors are opened.
•It is normal for droplets to form on the back wall
after the refrigerator self-defrosts.
•Locate air vents by using your hand to sense
airflow and move all packages that block vents
and restrict airflow. Refer to “Ensuring Proper Air
Circulation” section for the location of air vents.
24
TROUBLESHOOTING GUIDE TROUBLESHOOTING GUIDE
Problem Possible Causes Solutions
CUBES
PRODUCED BY
ICE MAKER ARE
TOO SMALL
•Water shutoff valve connecting
refrigerator to water line may be
clogged.
•Call a plumber to clear the valve.
ICE HAS BAD
TASTE OR ODOR
•The ice maker was recently installed.
•The ice has been stored for too long.
•The food has not been wrapped
tightly in either compartment.
•The water supply contains minerals
such as sulfur.
•The interior of refrigerator needs
cleaning.
•Ice storage bin needs cleaning.
•Discard first few batches of ice to avoid discolored
or off-flavored ice.
•Throw away old ice and make new supply.
•Rewrap foods since odors may migrate to the ice if
food is not wrapped properly.
•A new filter may need to be installed to eliminate
taste and odor problems.
•See “Care and Cleaning” section.
•Empty and wash bin. Discard old cubes.
THERE IS WATER
IN THE DEFROST
DRAIN PAN
•The refrigerator is defrosting.
•It is more humid than normal.
•The water will evaporate. It is normal for water to
drip into the defrost pan.
•Expect that the water in the defrost pan will take
longer to evaporate. This is normal when it is hot
or humid.
THE
REFRIGERATOR
SEEMS TO MAKE
TOO MUCH NOISE
•The sounds may be normal for your
refrigerator.
•Refer to the “Understanding sounds you may
hear” section.
FROST OR ICE
CRYSTALS ON
FROZEN FOOD
•The door is not closing properly.
•The door is opened often.
•See “Doors will not close completely” above.
•When the door is opened, warm, humid air is
allowed in the freezer resulting in frost.
THE ICE MAKER IS
NOT PRODUCING
ICE OR ICE CUBES
ARE FREEZING
TOO SLOWLY
•The freezer temperature is cold
enough to produce ice.
•Door left open.
•Wait 24 hours after hook-up for ice production.
See the “Control Panel Features” section.
•Check to see if something is holding the door
open.
AUTOMATIC ICE
MAKER DOES
NOT WORK
•Ice maker power switch on OFF (O)
position.
•Water supply turned off or not
connected.
•Freezer compartment too warm.
•Piled up the cubes in the storage
bin cause the ice maker to shut off.
•Move the switch to the ON (I) position.
•See the “Connecting the Water Line” section.
•Wait 24 hours for the freezer to reach its ideal
temperature.
•Level cubes by hand or shake the bin occasionally.
NOT DISPENSING
ICE
•All the doors are not closed
completely.
•The dispenser display is locked.
•Ice is not selected on the dispenser
•The ice dispenser is not used often.
•Ice bin is not installed correctly.
•New installation.
•Ice cubes are stuck in the delivery
chute.
•Ice will not dispense if any of the refrigerator doors
are left open.
•Press and hold the Lock button for 3 seconds to
unlock the control panel and dispenser.
•The dispenser can be set for ice or water. Make
certain that the control panel is set for the proper
operation. Press the dispenser button on the
control panel to cycle through the ice and water
options.
•Check the ice bin for ice cubes clumping/ sticking
together. If they are, break up the ice cubes allow
for proper operation.
•Be sure to install the ice bin firmly into position.
•Wait 24 hours after ice maker installation for ice
production to begin. Wait 72 hours for full ice
production.
•Use a plastic utensil to clear the delivery chute.
25
TROUBLESHOOTING GUIDE TROUBLESHOOTING GUIDE
Problem Possible Causes Solutions
CUBES
PRODUCED BY
ICE MAKER ARE
TOO SMALL
•The ice dispenser is stalling while
dispensing “crushed” ice.
•Ice maker power switch in the OFF
(O) position.
•Water supply turned off or not
connected.
•Change the ice button from “crushed” to “cubed”. If
cubed ice dispenses correctly, depress the button
for“crushed” ice and begin dispensing again.
•Move the switch to the ON (I) position.
•See the “Connecting the Water Line” section.
ICE HAS BAD
TASTE OR ODOR
•The dispenser display is locked.
•New installation.
•Refrigerator or freezer doors are not
closed properly.
•Water supply turned off or not
connected.
•The water pressure is less than 40
PSI.
•Home filter or reverse osmosis
system is used.
•The dispenser is not set for water
dispensing.
•Press and hold the Lock button for 3 seconds to
unlock the control panel and dispenser.
•Flush and fill the water system.
•Water will not dispense if any of the refrigerator
doors are left open.
•See the “Connecting the Water Line” section.
•The water pressure to the home affects the flow
from the dispenser.
•This can decrease water pressure. It is
recommended not to connect the supply line to
a reverse osmosis system for optimal operation.
•The dispenser can be set for ice or water. Make
certain that the control panel is set for the proper
operation. Press the dispenser button on the
control panel to cycle through the ice and water
options.
1-800-243-0000
1-888-865-3026
1-888-542-2623
USA, Consumer User
USA, Commercial User
CANADA
LG Customer Information Center
www.lg.com
Register your Product Online!
