Loading ...
Loading ...
Loading ...
26
27
FINAL CHECK
Operate all cooker burners on high and low flames and check that each burner ignites
properly and has a stable flame. The following may be considered to be abnormal:
• If
theburnershaveyellowtipping.
• Ifthepotsaresootingupunderneath.
• Iftheburnersareextinguishedbyopeningandclosingtheovendoor.
• Iftheburnersfailtoigniteproperly.
• Iftheburnersfailtoremainalight.
• Iftheelectrodesconstantlyclickwhenburnersarealight.
When satisfied with the operation of the cooker, please explain to the user the correct
method of operation. If the cooker fails to operate correctly, contact your local service
agent.
Gas checks and adjustments -igniter operation
Check that the igniter for each burner successfully ignites the gas and that the burner
remains alight. If an igniter fails to work or a burner fails to remain alight, fi
rst remove the
plug from the electrical power outlet, and then check that all the electrical connections
are in place. If the upright cooker fails to operate correctly, call Glem Gas Appliances Pty
Ltd or their appointed agent for service. Do not attempt repairs yourself.
Gas checks and adjustments -pressure adjustment
First shut off the gas to the appliance. Remove the sealing screw from the regulator test
point at the rear of the cooker and attach the hose from the mamometer to the point.
Turn the gas back and light the largest burner and smallest burner at the maximum
setting. Check the pressure and adjust at the regulator if necessary to the settings in the
table or on the data plate. For propane gas adjust at the regulator at the cylinder. Turn
regulator adjusting screw clockwise to increase pressure and anti clockwise to reduce
pressure. Refit the test point sealing screw when finished.
NOTE!
THIS COOKER MUST BE INSTALLED BY A LICENSED GAS FITTER.
WRITTEN PROOF IS REQUIRED FOR WARRANTY SERVICE.
STANDARD PLUMBERS TEFLON TAPE SHOULD NOT BE USED TO SEAL
JOINTS. AN APPROPRIATE GAS SEALING TAPE MUST BE USED.
IF IN DOUBT ON ANY INSTALLATION POINTS PLEASE CALL 1300 307 917
FOR MORE INFORMATION.
QUICK REFERENCE FAULT FINDING CHART
GAS COOKTOP
Burner does not stay alight after several attempts
Check that the burner is correctly assembled. Sometimes the parts get misaligned and
that interrupts correct gas flow.
Make sure the gas supply is turned on.
Make sure that the burner is dry and clean.
Ensure there is nothing blocking the gas inlet on the burner or the slots in the flame
spreader.
Try to light the burner using a match, this will identify if it is an ignition fault.
Burner will not stay alight
Check that the burner is correctly assembled.
There is a thermocouple valve on each burner. It is a tapered copper point. If the
thermocouple is faulty the flame will not stay alight once you release the control knob.
Hold the knob in for a few seconds to make sure that the thermocouple reaches
temperature.
The ignitor does not spark
While it is not always possible to see the spark there is a clicking sound when the
ignitor is operating.
Make sure the ignitor is clean and dry (this is the cylindrical white point at the edge of
the burner)
Make sure that the burner is correctly assembled.
Make sure that the electricity is turned on.
The flame suddenly looks different
This usually means that the burner is not assembled correctly.
GAS OVEN
Oven wont light
Make sure the gas supply is turned on and the knob turned to maximum temperature
Make sure the oven door is open
Make sure that the electricity is connected and turned on
Get the electronic ignition sparking before turning on the gas, this is the best way to
encourage the burner to light.
Try to light the oven manually to check if the problem is electronic ignition related
Oven wont stay alight
Once the oven is lit hold the control knob in for 20 seconds to heat the thermocouple
which will maintain the flame.
Loading ...
Loading ...