Loading ...
Loading ...
Loading ...
18
ELECTRONIC CONTROLS SET-UP INSTRUCTIONS
CODE EXPLANATION
H.00
EXTRA
RINSE
EXTRA RINSE Upgrade Price - Increase or decrease between 0
and 200 by pressing the LEFT UPPER or RIGHT UPPER key pad.
Factory preset for 0 quarters = $0.00.
g Press the LEFT MIDDLE key pad once to advance to next code.
J.Cd
COIN/DEBIT OPTION
J.Cd
Both coin & debit selected.
J.C_
Coins selected, debit disabled. Press the LEFT LOWER key pad
3 times for this selection.
J._d
Debit Card selected, coins disabled. Press the LEFT LOWER key
pad 3 times for this selection.
J.Ed
Enhanced Debit is self-selected when a Generation 2 card reader
is installed in the washer. The Ed option cannot be manually
selected or deselected.
g Press the LEFT MIDDLE key pad once to advance to next code.
L.00
PRICE SUPPRESSION OPTION
This option causes the customer display to show ‘ADD’ or
‘AVAILABLE’ rather than the amount of money to add. (Used
mainly in debit installations.)
L.00
Not Selected ‘OFF’.
L.PS
Selected ‘ON’. Press the LEFT LOWER key pad once for this
selection.
g Press the LEFT MIDDLE key pad once to advance to next code.
n. CE
CLEAR ESCROW OPTION
When selected, money held in escrow for 30 minutes without
further escrow or cycle activity will be cleared.
n. CE
Selected ‘ON’.
n. 00
Not selected ‘OFF’. Press the LEFT LOWER key pad once to
deselect this selection.
g Press the LEFT MIDDLE key pad once to advance to next code.
U.00
PENNY INCREMENT OFFSET
U.00
This represents the penny increment price offset used in
Generation 2 (Enhanced Debit) PR models. Choose from 0-4
pennies by pressing the LEFT UPPER key pad.
g Press the LEFT MIDDLE key pad once to advance to next code.
A3.02
NORMAL Cycle Settings. Allows the owner to select the cycle
default options of Water Temperature, Soil Level, and Extra Rinse.
See Table 1 for specic settings. Normal is set to 02 from the
factory.
A4.00
DELICATES Cycle Settings. Allows the owner to select the cycle
default options of Water Temperature, Soil Level, and Extra Rinse.
See Table 1 for specic settings. Delicates is set to 00 from the
factory.
A5.OF
POWERWASH Cycle Settings. Allows the owner to select the cycle
default options of Water Temperature, Soil Level, and Extra Rinse.
See Table 1 for specic settings. Powerwash is set to 0F from the
factory.
If cycle counter (9.0C) is selected, the following is true:
1 xx Number of cycles in THOUSANDS. 1 02 = 2,000
2xxx Number of cycles in ONES. 2225 = 225
TOTAL CYCLES = 2,225
This is “VIEW ONLY” and cannot be cleared.
Press the LOWER MIDDLE key pad once to advance
to next code.
If money counter (1.0C or 1.C0) is selected, the following is
true:
3 xx Number of dollars in HUNDREDS. 3 01 = $1,000.00
4xxx Number of dollars in ONES. 4600 = $ 600.00
5 xx Number of CENTS. 5 75 = $ 00.75
TOTAL = $1,600.75
END OF SET-UP PROCEDURES
EXIT FROM SET-UP MODE
n PD Models: Reinstall access door.
n PR Models:
g
Unplug washer or disconnect power.
g
Open console, reinsert plug into AA1, close console.
g
Plug in washer or reconnect power.
If preferred, just wait through 2 minutes of inactivity. All settings
will be saved and the display will revert to Select Cycle screen.
A3, A4,
or A5
Extra
Rinse
Soil
Level
Wash
Temp
A3, A4,
or A5
Extra
Rinse
Soil
Level
Wash
Temp
00 Off Off Cold 08 On Off Cold
01 Off Off Cool 09 On Off Cool
02 Off Off Warm 0A On Off Warm
03 Off Off Hot 0b On Off Hot
04 Off On Cold 0c On On Cold
05 Off On Cool 0d On On Cool
06 Off On Warm 0E On On Warm
07 Off On Hot 0F On On Hot
Table 1
Technician Service Access Code
This method is only available on washers set to free vend (6 00).
To enter service mode:
Press the LEFT UPPER, RIGHT LOWER, RIGHT UPPER, and
LEFT LOWER key pads within 10 seconds.
To exit service mode:
From service code 8.xx, press the LEFT UPPER key pad
for 4 seconds
or
Wait 2 minutes without touching any key pads (without diagnostic
modes running)
or
Power down the washer, then reapply power
NOTE: If a service cycle is in progress upon exiting service mode,
the cycle will complete normally with cycle status information
displayed. The display will resume normal customer operation
mode when the cycle ends.
Loading ...
Loading ...
Loading ...