Loading ...
Loading ...
Loading ...
8
■ To add rinse aid, turn the dispenser
cap ¼ turn counterclockwise and lift
off. Pour rinse aid into the opening
until the indicator level is at “Full.”
Replace the dispenser cap and turn
to “Lock.” Make sure cap is fully
locked.
NOTE: For most water conditions, the
factory setting will give good results. If
you have hard water or notice rings or
spots, try a higher setting. Turn the
arrow adjuster inside the dispenser by
either using your fingers or inserting a
flat-blade screwdriver into the center of
the arrow and turning.
Select a Cycle (cycles vary by model)
Press the Select Cycles button until the light below the desired
cycle is on.
NOTE: Heavier cycles and options affect cycle length. Some
cycles and options will take up to 3¹⁄₂ hours to complete.
Heavy – Use for heavily soiled, hard-to-clean items
Normal - This cycle with only the Heated Dry option selected, and
without other options selected, is recommended to completely
wash and dry a full load of normally soiled dishes. The energy
usage label is based on this cycle and option combination.
ECO – Use for lightly soiled items. It saves energy.
1 Hour Wash– Use for lightly soiled items. For fast results, 1-Hr
Wash will clean the dishes using slightly more water and energy.
Rinse Only – (no options apply to this cycle) Do not use
detergent. This is only a rinse that keeps food from drying on your
dishes and reduces odor buildup in your dishwasher until you are
ready to wash a full load.
Select Options (options vary by model)
You can customize your cycles by pressing the options desired.
Repeatedly press the button until the desired combination of
options is selected.
Hi Temp - (can be selected with Heavy and Normal wash cycles)
heats the water during the wash portions of the cycle.
Sani Rinse –
(can be selected with Heavy and Normal wash
cycles) Select this option to raise the water temperature in the final
rinse to approximately 155°F (68°C). Sani Rinse option adds heat
and time to the cycle. This high temperature rinse sanitizes your
dishes and glassware in accordance with NSF/ANSI Standard 184
for Residential Dishwashers. Certified residential dishwashers are
not intended for licensed food establishments. The Sanitized
indicator light will glow when Sanitized. It will blink if the Sanitize
temperature is not achieved.
Heat Dry – (can be selected with 1-HR Wash, Heavy and Normal
wash cycles) When selected with the 1-Hr Wash cycle, the time is
increased by approximately 30 minutes.
Delay Wash (4 HR) – (any cycle) offers the choice to start the
dishwasher automatically at a later time. Select a wash cycle and
options. Press DELAY or DELAY WASH. Press START/RESUME.
Close the door firmly.
Start or Resume a Cycle
■ Run hot water at the sink nearest your dishwasher until the
water is hot. Turn off water.
■ Push door firmly closed. The door latches
automatically. Select the wash cycle and options
desired OR press START/RESUME to repeat the
same cycle and options as in the previous wash
cycle. For top controls, select cycle and options
first, and then close the door.
■ You can add an item anytime before the main wash starts.
Open the door slowly and add the item. Close the door firmly.
Press START/RESUME.
■ The Clean indicator glows when the cycle is
finished. The Sanitized indicator glows when the
Sani Rinse option is selected and sanitization
levels occur. The Sanitized indicator light will
blink if the Sanitize temperature is not achieved.
STEP 3
¹⁄₄
turn to lock
Lock
6
5
4
3
2
-
-
-
max
fill
1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
max
fill
-
-
-
-
-
-
-
-
-
-
-
-
STEP 4
Loading ...
Loading ...
Loading ...