Loading ...
Loading ...
Loading ...
8
maker stops keeping warm at the pre-set auto off
time (min. 15 minutes / max. 5 hours).
• The pre-set auto off time disappears after
3 seconds.
• Press the AUTO OFF button (c) to switch off the
function: the green LED light disappears.
For your additional safety, the appliance will switch
off automatically 2 hours after the brewing cycle is
complete if the AUTO OFF function has not been
activated.
Setting the Water Hardness Level
Set the water hardness level on the coffee maker to
the water hardness level for your local area.
• Press the CLEAN button (f) for a minimum of
3 seconds.
• The default setting (h3) will start flashing.
• Press the SET button (e) to scroll through the
options (h1 = soft, h2 = normal, h3 = hard) and
select the appropriate water hardness level.
• Press the CLEAN button again to save the
hardness level.
• The pre-set water hardness disappears after
3 seconds and the time of day will show on the
LED control panel.
1 – 4 Cups Setting
• Press the «1-4» button (g). The green LED above
the button will illuminate.
• Press BREW (a) to start brewing.
• The green LED turns off after the brewing cycle is
finished.
Brew Strength Selector
• Press the STRENGTH button (h) to select one of
the two pre-set strengths («regular» or «bold»).
• The selected brew strength will show when power
is on.
Keep Warm Plate
• Press the TEMP button (i) to choose one of the
three pre-set keep warm settings («low», «med»
or «high»).
• The selected temperature will show when power is
on.
Making Coffee (B)
Before using the coffee maker for the first time,
after a long period of not using it, or after installing
a new charcoal water filter, run the coffee maker
through a complete brew cycle without ground coffee.
Use a full carafe (12 cups) of fresh cold water.
This will remove any dust from the manufacturing
process or residues that have remained in the unit.
• Open the reservoir cover (6).
• When filling the water reservoir (3) with fresh cold
water, refer to the carafe height markings or the
water level indicator (inside the water reservoir)
and fill to the desired number of cups.
• To prepare the exact amount of coffee for the
Braun Mug2Go (available separately as
accessory), fill to the corresponding water mark
(11 oz.) inside the reservoir.
• Insert the gold tone permanent filter (5) or a
paper filter (cone type # 4) in the filter basket (4).
• Add the desired amount of ground coffee,
corresponding to the number of cups being
brewed. We recommend using 1 tablespoon or
1 coffee scoop of ground coffee per cup, but use
more or less to suit your taste.
• Close the water reservoir and place the carafe in
its position on the keep warm plate (9).
• Plug the cord into an electrical outlet and press
the On/Off button (1).
• Press the BREW button (a) to start brewing
immediately or press AUTO ON (b) to commence
brewing at the pre-set time.
• During brewing, the indicator light will flash
continuously. Once the brewing cycle is complete,
the light will turn solid green indicating the coffee
maker is in «keep warm» mode.
NOTE: The anti drip system halts the flow of coffee
from the filter basket when the carafe is removed, so
a cup can be poured before brewing is finished.
The carafe should be returned to the keep warm
plate (maximum 20 seconds) to prevent the filter
basket from overflowing.
For Best Results
• Be sure to add a small amount of extra water to
account for the amount of water lost in wetting the
grounds and through evaporation during the
brewing process.
• When using paper filters, be sure that it is
completely open and fully inserted in the basket.
It may help to fold and flatten the seams of the
paper filter beforehand.
• Once the coffee has finished brewing, stir it
before serving to blend the flavors. The coffee at
the bottom of the carafe will be somewhat
stronger than the coffee at the top.
1321021IBR_KF 7150_7170_USCA_S6-28.indd 81321021IBR_KF 7150_7170_USCA_S6-28.indd 8 24.11.15 08:3824.11.15 08:38
Loading ...
Loading ...
Loading ...