Loading ...
Loading ...
Loading ...
Troubleshooting
First try the solutions suggested here. If you need further assistance or more recommendations that may help you to avoid a service call, or visit
producthelp.jennair.com. In Canada, visit www.jennair.ca.
Contact us by mail with any questions or concerns at the address below:
In the U.S.A.:
JennAir Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
In Canada:
JennAir Brand Home Appliances
Customer eXperience Centre
200 - 6750 Century Ave.
Mississauga, Ontario L5N 0B7
Please include a daytime phone number in your correspondence.
IF YOU EXPERIENCE RECOMMENDED SOLUTIONS
The Clean indicator
is flashing
Check the following:
■ Was the cycle interrupted? Touch START/CANCEL and close the door within 4 seconds.
■ Is the overfill protection float able to move up and down freely? Press down to release.
■ Be sure the water supply is turned on to the dishwasher. (This is very important following the new installation
of your dishwasher.)
■ Check for suds in the dishwasher. For more information on suds, see “Dishwasher does not clean completely.”
Dishes do not
dry completely
NOTE: Plastic and items with nonstick surfaces are difficult to dry because they have a porous surface which
tends to collect water droplets. Towel drying may be necessary.
Use of rinse aid along with the Precision Dry + option is needed for proper drying.
Proper loading of items can affect drying.
Glasses and cups with concave bottoms hold water. This water may spill onto other items when you are
unloading the dishwasher.
■ Unload the bottom rack first.
■ For improved results, place these items on the more slanted side of the rack.
Spotting/Filming
Liquid rinse aid is necessary for drying and to reduce spotting.
Use the correct amount of detergent.
Confirm that the cloudiness is removable by soaking the item in white vinegar for 5 minutes. If the cloudiness
disappears, it is due to hard water. Adjust the amount of detergent and rinse aid. See the “Dishwasher Care”
section. If it does not come clear, it is due to etching.
Be sure the incoming water temperature is set at 120°F (49°C).
Try using the Hi-Temp Wash or Sanitize Rinse options.
To remove spotting, see the “Dishwasher Care” section.
Dishwasher does not
clean completely
Be sure the dishwasher is loaded correctly. Improper loading can greatly decrease the washing performance.
See the “Operating Your Dishwasher” section.
Check filter to ensure it is properly installed. Clean it if needed. See the “Filtration System” section in the full User
Instructions for details.
Select the proper cycle for the type of soils. The Sensor cycle can be used for tougher loads.
Be sure the incoming water temperature is at least 120°F (49°C).
Use the proper amount of fresh detergent. More detergent is needed for heavier-soiled loads and hard
water conditions.
Scrape food from dishes prior to loading (do not prerinse).
If foam or suds are detected by the dishwasher sensing system, the dishwasher may not operate properly
or may not fill with water.
Suds can come from:
■ Using the incorrect type of detergent, such as laundry detergent, hand soap, or dish detergent for hand
washing dishes.
■ Not replacing the rinse aid dispenser cap after filling (or refilling) the rinse aid dispenser.
■ Using an excessive amount of dishwasher detergent.
Interior tub lights
do not light up
(on some models)
The interior lights turn on when the door is opened. The lights will turn off automatically after 15 minutes if the door
is left open.
If the lights do not turn on after closing and opening the door, call for service.
7
Loading ...
Loading ...
Loading ...