Loading ...
Loading ...
Loading ...
11
Drain water
Drenaje de agua
HOW TO ATTACH THE DRAIN PAN (OPTIONAL)
COMO INSTALAR LA BANDEJA DE DRENAJE (OPCIONAL)
Maximum
13/32”
Máxima
de 13/32”
Condensed water
Agua condensada
Remove the
rubber plug
Quite el
tapón de
goma
Note: Drain hose or tubing can be purchased locally to satisfy your particular needs.
Nota: El tubo o la manguera de drenaje puede ser comprado localmente de acuerdo a sus
necesidades particulares.
To get the maximum cooling efficiency, this air
conditioner is designed to splash the condensed
water on the condenser fin.
This method is called “Slinger-Up System”.
If the splashing sound annoys you, you can provide
an outside drain by using the following proce-
dure which may, however, cause a small loss of
performance.
Screws
Tornillos
INTERNAL VIEW
VISTA INTERIOR
Install the drain pan, at
the right corner of the
cabinet using 2 screws
(part no. CWG86C733).
Instale la bandeja de
drenaje en la esquina
derecha de la caja con
dos tornillos (serie no.
CWG86C733).
Insert the
drain hose
to the drain
pan.
Inserte la
manguera
de drenaje a
la bandeja
de drenaje.
EXTERNAL VIEW
VISTA EXTERIOR
Bottom-side view with drain pan and hose
in place.
Vista inferior con la bandeja de drenaje y
la manguera de drenaje ya instaladas.
PLACE FRONT INTAKE GRILLE ONTO THE FRONT GRILLE
COLOQUE LA REJILLA FRONTAL DE TOMA DE AIRE SOBRE LA REJILLA FRONTAL
Slide the front intake grille slightly to the right to reattach the tabs and then
push it down to close tight.
Deslice la rejilla frontal de toma de aire un poco a la derecha para readjuntar
las lengüetas y luego tire hacia abajo para dejar bien cerrado.
NOTE:A “click” sound can be heard when the front intake grille is pushed down.
NOTA: Se puede escuchar un “click” cuando la rejilla frontal de la toma de aire es
empujada hacia abajo.
Note: The drain pan (part no. CWH40175) can
be obtained from nearest servicenter.
Nota: La bandeja de drenaje (serie no.
CWH40175) puede ser obtanido en su
servicentro más cercano-pagadero.)
1
Slide the chassis out from the cabinet
(refer to page 8) and remove the rubber
plug.
1
Deslice el chasis hacia afuera del caja
(diríjase a la página 8) y quite el tapon de
goma.
Drain pan (optional)
Bandeja de drenaje (opcional)
3
Connect a drain hose (optional)
3
Conectar la manguera de drenaje (opcional)
4
Slide the chassis back into the cabinet
Re-install the chassis locking brackets
4
Deslice el chasis hacia el interior de la caja
Reinstale los soportes de bloqueo del chasis
2
Install the optional drain pan (part no. CWH40175)
2
Instale la bandeja opcional de drenaje (serie no. CWH40175)
Drain hose
(not included)
Manguera
de drenaje
(no incluido)
11
Note: The cabinet should be installed tilted slightly lower to the rear for
necessary condensate drainage. (Max. 13/32”)
Para obtener la máxima eficiencia de enfriamiento, este acondicionador de
aire fue diseñado para salpicar el agua sobre el serpentin de condensación.
Este método se llama “Sistema tipo salpicador”.
Si el ruido producido al salpicar le molesta, puede instalar una manguera de
drenaje usando el siguiente procedimiento, sin embargo, esto producirá una
baja en el rendimiento.
Nota: El armario debe de estar un poco inclinado, más bajo que la parte trasera
para el drenaje necesario de la condensación. (Máxima de 13/32”)
Loading ...
Loading ...
Loading ...