Asko DBI243IBW Turbo Drying Under Bench Dishwasher

User Manual - Transcript

• Page 1: Dishwasher DBI243IBOPERATING INSTRUCTIONS EN
• Page 2 - English - : Contents 2Your dishwasher 3Safety instructions 4Before washing for the first time 5Loading the dishwasher 8Using the dishwasher 12Settings 14Care and cleaning 16Troubleshooting 19Technical information 20Installation 24ASKO Service 24Information for test institute 25Your notes 28Quick guide Your dishwasher Open the door and press the main power switch quotWelcome to your ASKO First time setupquot is shown on the display the first time the dishwasher is switched on It is important that you choose the right settings to ensure good dishwashing results See page 4 215Eco Display StartStop Navigation buttons for selecting a program Option Delayed Start Option Extra Dry Main power switch Program mode selector Speed mode Night mode Child lock Top up rinse aid
• Page 3 - English - : Safety instructions Read the operating instructions and keep them in a safe place Number of place settings 14 Never use the dishwasher for any purpose other than that specified in these operating instructions Do not load the dishwasher door or dishwasher baskets with anything other than dishes Never leave the dishwasher door open as someone may trip on it Use only dishwasher detergent This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard Damaged mains cables must only be replaced by a qualified electrician This appliance is intended to be used in household and similar applications such as staff kitchen areas in shops offices and other working environments farm houses by clients in hotels motels and other residential type environments bed and breakfast type environments Never place dishes with solvent residues in the dishwasher due to the risk of explosion Nor may dishes that contain ash wax or lubricants be washed in the dishwasher Children must be watched Do not allow children to use or play with the dishwasher Be especially vigilant when the door is open Some detergent may remain inside After adding detergent always start the dishwasher immediately WARNING Knives and other pointed items must be placed with the points down in the cutlery basket or horizontally in other baskets WARNING Dishwasher detergents are strongly alkaline They can be extremely dangerous if swallowed Avoid contact with skin and eyes and keep children away from the dishwasher when the door is open Seek medical attention if swallowed Check that the detergent compartment is empty after completion of the wash cycle Activate child lock Kid Safe You can activate the child lock button lock to prevent children from starting the dishwasher See the chapter Settings Installation See the chapter Installation Winter storageTransport Store the dishwasher above freezing temperature and avoid long transport distances in very cold weather Transport the dishwasher upright or laying on its back Overflow guard function The overflow protection starts pumping out the machine and turns off the water supply if the water level in the dishwasher exceeds the normal level If the overflow protection is triggered turn off the water supply and call the service department Packing material The packaging protects the product during transport The packaging material is recyclable Separate the different packaging materials to help reduce raw material use and waste Your dealer can take the packaging for recycling or direct you to the nearest recycling centre The packaging is comprised of Corrugated cardboard made from up to 100 recycled material Expanded polystyrene EPS with no added chlorine or fluorine Supports made from untreated wood Protective plastic made from polyethylene PE Disposal The dishwasher is manufactured and labelled for recycling When the dishwasher has reached the end of its service life and is to be disposed of it should immediately be made unusable Pull out the power cable and cut it as short as possible Contact your local authority for information about where and how your dishwasher should be correctly recycled
• Page 4 - English - : Before washing for the first time 1 Checking water hardness Contact the local water utility to check the water hardness in your area This is important with regard to how much detergent and rinse aid to use 2 Basic settings Open the door and press the main power switch quotWelcome to your ASKO First time setupquot is shown on the display It is important that you choose the right settings to ensure good dishwashing results English Main power switch Confirm settingSelect setting Settings Language1 Select the language to be shown on the display Set level of rinse aid 0123452 By using rinse aid you will improve your drying result You will also achieve a better dishwashing result with glassware and dishes Select rinse aid dosage The rinse aid dispenser can be adjusted between 0 Off and 5 High dosage Preselected at factory 5 Top up rinse aid Press to open 1 Open the rinse aid compartment lid 2 Carefully top up with rinse aid to the level marked max 3 Wipe up any splashes of rinse aid around the compartment 4 Close the lid firmly For water with a hardness greater than 1012 dH you ought to use rinse aid with citric acid known as acid rinse aid To change the chosen setting see the chapter Settings
• Page 5 - English - : Loading the dishwasher Greener dishwashing Do not rinse under running water Simply scrape off large food particles before loading the dishwasher Choose a green detergent Read the environmental declaration on the packaging Run programs only with a full load Wait to run a program until the dishwasher is full This way you save energy Use the Rinse amp hold program to rinse the dishes if there are any unpleasant odours while you wait for the dishwasher to become fully loaded Run programs at a lower temperature If the dishes are only slightly dirty you can select a program with a low temperature Select Eco Use when you want to save water and energy For normally soiled load such as plates serving dishes cups glasses and so on This dishwashing program is designed for an effective wash using as little energy and water as possible The program washes at a low temperature for a long time Open the door a little once the program has finished Better drying results are achieved if you open the door a little once the program has ended If the dishwasher is builtin the surrounding cabinets must be resistant to any condensation from the dishwasher Connect to cold water Connect the dishwasher to the cold water supply if the building is heated using oil electricity or gas Connection to hot water supply Connect the dishwasher to the hot water supply max 70 C if the building is heated using an energyefficient means such as district heating solar power or geothermal power Choosing a hot water connection cuts dishwashing times and reduces the dishwashers energy consumption NOTE Do not exceed the permitted water supply temperature Certain materials used in some cookware cannot withstand high heat Fragile dishes Some cookware is not dishwasher safe This can be for several reasons Some materials cannot withstand strong heat others can be damaged by dishwashing detergent Exercise caution with for example handmade items fragile decoration crystalglassware silver copper tin aluminium wood and plastic Look for the quotDishwasher safequot marking Fragile decoration Porcelain with decoration on top of the glazing the items feel rough should not be washed in a dishwasher CrystalGlass By using rinse aid you will improve your drying result You will also achieve a better dishwashing result with glassware and dishes Handpainted glassware as well as antique and very fragile items should not be washed in a dishwasher Silver Silver and stainless steel items should not come into contact as the silver can become discoloured Aluminium Aluminium can lose its shine if washed in a dishwasher However good quality aluminium pans can be washed in a dishwasher even if some of the shine will be lost Cutlery with glued handles Some types of glue are not dishwasher safe In such cases the handles may loosen Points to consider All dirty surfaces should face inwards and downwards Dishes should not be placed in or on each other Angle dishes with hollows such as cups so that the rinse water will run off This is also important for plastic items Make sure small items cannot fall through the dishwasher basket place them in the cutlery basket NOTE Check that the spray arms can rotate freely
• Page 6 - English - : The dishwashers baskets The dishwasher is equipped with an upper basket and a lower basket with a cutlery basket The appearance of the baskets may differ depending on the dishwasher setup Upper basket Place glasses cups bowls side plates and saucers in the upper basket All dirty surfaces should face inwards and downwards Wine glasses are placed on the wine glass shelf and knives are placed in the knife stand on the right Lower basket Place plates side plates serving dishes pots and cutlery in the cutlery basket in the lower basket Place pots and pans in the rear right part of the lower basket to achieve the best dishwashing results from the rear of the two spray nozzles WideSpray which are intended for these types of dishes Foldable tines Lower the foldable tines plate supports when washing pots and pans Release the foldable tines by pressing the catch inwards before adjusting their position Washing large plates Move the foldable tines and their mounts to widen the distance between the tine rows to adapt the lower basket to plates with a diameter greater than 25 cm Accessory Buy a wine glass shelf with space for six tall 1 wine glasses The wine glass shelf is designed to ensure optimal washing and drying results with tall wine glasses The wine glass shelf is placed in the rear section of the lower basket This accessory can be purchased by calling ASKO Cutlery basket Place cutlery with the handles facing down except for knives and spread them out as much as possible Ensure that spoons do not stack inside each other The cutlery basket is best placed in the middle at the front of the lower basket to achieve the best dishwashing performance from the unique spray nozzle Power Zone Cutlery which is intended for the cutlery basket WARNING Knives and other pointed items must be placed with the points down in the cutlery basket or horizontally in other baskets Folddown section for small items The cutlery basket has a folddown section in the middle for small items or small shafts such as electric whisk attachments 1 Height max 25 cm Diameter max 75 cm
• Page 7 - English - : Cutlery basket with lid The cutlery basket lid can be removed and used for example as an extra cutlery basket in the upper basket see below Accessory Buy an extra cutlery basket The extra cutlery basket is flexible and can be dismantled and attached to the lower basket or the large cutlery basket to make an extra large cutlery basket This accessory is available where you purchased your dishwasher
• Page 8 - English - : Using the dishwasher Add detergent Press to open 1 Prewash detergent compartment 2 Main wash detergent compartment Detergent is added according to water hardness Follow the instructions on the detergent packaging Too much detergent can result in less effective dishwashing and also entails greater environmental impact The detergent compartment must be dry when adding detergent There is one compartment for the prewash and one for the main wash If powder or liquid dishwasher detergent is used add a small amount of the detergent to the prewash compartment Contact the detergent manufacturer if you have questions about the detergent NOTE Use only dishwasher detergent Washing up liquid must not be used as the foam that forms prevents the dishwasher from operating effectively Dishwasher tablets Halve the tablet if it is difficult to close the dispenser lid There is a risk that the detergent will not be released properly if the lid is tight and will not open correctly NOTE Dishwasher tablets are not recommended for short programs less than 75 minutes Use powder or liquid dishwasher detergent instead Allinone detergent There are many types of allinone detergents on the market Read the directions for these products carefully NOTE Optimum washing and drying results are achieved by using normal dishwasher detergent together with separately dispensed rinse aid
• Page 9 - English - : 215Eco Starting the dishwasher Select a program mode Select any options Press and hold the main power switch until the display lights up Select the program The main power switch Open the door and press the main power switch Close the door Also turn on the water tap if it is turned off Select a program To select a program press the navigation button until the desired program is shown on the display Select a programme to suit the type of dishes and how dirty they are Eco Use when you want to save water and energy For normally soiled load such as plates serving dishes cups glasses and so on You can read more about greener dishwashing in the chapter Loading the dishwasher Heavy Use to wash normally soiled load such as plates serving dishes cups glasses and so on Time program The program adapts to the specified running time or finish time With this program it is important to choose a time suited to how dirty the dishes are Slightly dirty dishes015045 Normally dirty dishes100130 Very dirty dishes200230 Press the option button to set the desired program time Rinse amp hold Used to rinse dishes while you wait for the dishwasher to become fully loaded Hygiene This program is designed to meet strict hygiene demands Quick A short program for slightly soiled dishes This program is not intended for burnt food such as on oven dishes Intensive Program for very dirty dishes such as pans casserole dishes and oven dishes If these dishes do not completely fill the dishwasher you can add plates and the like Select a program mode To select a program mode press the program mode selector until the desired mode is shown on the display The available program modes vary between programs Speed mode The program time is shortened but the dishwasher uses more energy Night mode Lower noise level during the dishwashing program The program time is extended Select an Option To select an option press the option button until the desired option is shown on the display The available options vary between programs Extra Dry A higher temperature in the final rinse and a longer drying cycle improve the drying results if you activate this option Energy consumption is slightly increased Delayed Start When you select Delayed Start the dishwasher will start in 124 hours after you have pressed the button StartStop and closed the door 1 Press the button once to activate Delayed Start Press the button several times or hold it in to set the desired number of hours 2 Press StartStop and close the door The timer counts down and the dishwasher starts after the selected delay If you want to cancel the Delayed Start option open the door then press and hold StartStop for three seconds START STOP Starting the dishwasher Close the door properly otherwise the dishwasher will not start Press StartStop until the display shows quotProgram startedquot If the dishwasher is not started within 2 minutes of the last button press the machine switches off
• Page 10 - English - : Time remaining Once you have chosen a program a program mode and options the time the program took when last used is displayed Once you have started the dishwasher the display shows the remaining program time The remaining time is updated after the water for the final rinse has been heated This may differ somewhat from time to time depending on the temperature of the water supply the amount of dishes the ambient temperature and other factors During the first run of each program the remaining time displayed can be slightly misleading as the dishwasher is estimating the time When you run the program a second time the dishwasher will calculate the remaining time based on the previous duration of the program Stopping or changing a program In order not to accidently press a button and cancel the current program you must press and hold StartStop for five seconds if you want to change programs after starting the dishwasher Add more detergent if the lid of the detergent dispenser has opened Then choose a new program and press StartStop If you want to load more dishes Open the door The dishwasher stops automatically Add the dishes and close the door After a while the dishwasher continues the program If the dishwasher is turned off due to a power failure If the dishwashing program was not finished the interrupted program continues when power is restored NOTE During drying the program is interrupted if the power is cut or the door is open for more than 2 minutes Once the program has finished Once the program has finished END appears on the display At the end of the program you will hear a short beep Chapter Settings describes how to change this function The dishwasher switches off automatically after the program ends Turn off the water tap after each use How to get the best drying results Fully load the dishwasher Angle dishes with hollows such as cups so that the rinse water will run off This is also important for plastic items Top up with rinse aid or increase the rinse aid dosage level Activate the Extra Dry option Activate the High temperature setting See the chapter Settings Activate the Extra Dry setting See the chapter Settings Open the door a little once the program has finished Allow the dishes to cool before unloading the dishwasher Unloading the dishwasher Hot porcelain is more fragile Leave the dishes to cool in the dishwasher before unloading them Unload the lower basket first to avoid any water drops from the upper basket falling onto the dishes in the lower basket
• Page 11 - English - : Program chart Consumption values 1 Final rinseNumber of rinses Main washPrewashesProgram mode Option Detergent compartment ml Program Water cons liter Hot water 3 Cold water 2 Energy approx kWh Dishwashing time approx hrsmin Energy approx kWh Dishwashing time approx hrsmin 127042240723548 C346 C225 Eco 4 13062051222565 C260 C225Heavy 111904120152300516015230lt65 C23lt65 C0225Time program 3001007001007 C1Rinse amp hold 10091001411070 C270 C25Hygiene 15091201413065 C365 C125Quick 14132351725570 C270 C225Intensive 1 Consumption values vary depending on the temperature of the incoming water room temperature load size selected additional functions and more 2 Connection to cold water approx 20 C 3 Connection to hot water approx 60 C The hot water connection figures do not include the energy used to heat the inlet hot water before entering the dishwasher 4 The energy label performance figures are based on this program which is recommended for normally soiled load at the rated capacity No options
• Page 12 - English - : Settings Open the dishwashers Settings menu To open the dishwashers Settings menu press the navigation button until Settings menu is shown on the display and confirm your selection using the mode selector To exit the dishwashers Settings menu select Exit and confirm your selection using the mode selector 2 Child lock On Mode selector to confirm current setting Settings Current setting Navigation button for selecting a setting OptionsSettings You can choose the language used for the displayEnglish AUSvenskaDanskNorskSuomi NederlandsFrançaisDeutschItaliano Русский EspañolPortuguêsSloven EestiLatviešuLietuvi ų HrvatskiPolish 简体中文 繁體中文 日本語 Language1 You can activate the child lock button lock to prevent children from starting the dishwasher OnOffChild lock2 To temporarily deactivate or activate the child lock press and hold the mode selector and the option button Delayed Start for 3 seconds Setting to hide the logo shown on the displayLogotype OnOffDisplay3 For adjusting the contrast of the displayContrast 1234 You can select which information is shown on the displayProg Info screen TS SSymbol Symbol 007 TText Text Rinse amp hold 007 This sound is used to confirm each button pressFeedback 0123Sound4 The buzzer indicates when a dishwashing program has endedVolume 0123 Error messages are always indicated by a loud buzzer Setting for rinse aid dosage The rinse aid dispenser can be adjusted between 0 Off and 5 High dosage 012345Rinse aid5 Increase the rinse aid dosage If the dishes have water marks Decrease the rinse aid dosage If the dishes have a sticky whiteblue film If the dishes are streaked Buildup of foam If you have very soft water the rinse aid can be diluted 5050 with water Super rinse adds two extra rinsesOnOffSuper rinse6 Activated in the following programs Heavy Intensive
• Page 13 - English - : OptionsSettings Activate the setting High temperature to improve the dishwashing results Energy consumption is slightly increased OnOffHigh temperature7 Activated in the following programs Heavy Intensive To exit the dishwashers Settings menu select Exit and confirm your selection using the mode selector Exit
• Page 14 - English - : Care and cleaning Top up rinse aid When the rinse aid needs topping up the above symbol lights on the display Press to open 1 Open the rinse aid compartment lid 2 Carefully top up with rinse aid to the level marked max 3 Wipe up any splashes of rinse aid around the compartment 4 Close the lid firmly After topping up it may take a while before the symbol goes out NOTE For water with a hardness greater than 1012 dH you ought to use rinse aid with citric acid known as acid rinse aid Coarse filter The coarse filter traps larger food particles which cannot get past the drainage pump Empty the coarse filter when necessary Coarse filter 1 Lift the coarse filter by the handle 2 Empty the coarse filter Remember to refit it Fine filter Debris that collects on the fine filter is automatically rinsed away during each wash Clean the fine filter when necessary Fine filter 1 Turn the handle anticlockwise 2 Lift the filter straight up using the handle Free the coarse filter to clean the fine filter 3 Refit in reverse order Check that the edges seal properly when refitting the fine filter 4 Lock the filter in place by turning the handle clockwise to the stop position The handle should point straight out from the dishwasher NOTE Dishwashing results may be affected if the filters are incorrectly fitted Note that the dishwasher must not be used without the filters in place NOTE Check that the coloured stop on the right in the bottom drain is in place Spray arms Holes and bearings can sometimes become blocked Remove any debris using a pin or something similar The spray arms also have holes on their undersides To facilitate cleaning you can remove the spray arms Remember to fit them firmly back into place after cleaning Upper spray arm The upper basket must be removed before the upper spray arm can be released Pull out the upper basket and turn the basket catch on each runner outwards see illustration The basket can now be removed Pull the upper spray arm straight up to release it Lower spray arm Pull the lower spray arm straight up to release it
• Page 15 - English - : The door and the door seal Regularly clean the sides of the door and the door seal Use a slightly damp cloth with a little cleaner if necessary Front panel Keep the buttons clean and free from grease Wipe them clean with a dry or slightly damp cloth Never use cleaners they can scratch the surface Use the main power switch to turn off the dishwasher before cleaning the buttons to avoid activating any buttons unintentionally The dishwasher tub The dishwasher tub is made of stainless steel and is kept clean through normal use Limescale deposits If you have hard water limescale deposits may build up in the dishwasher If this happens run the Intensive program with two tablespoons of citric acid in the detergent compartment with no dishes in the machine Special dishwasher cleaners are also available on the market Unblocking the drainage pump If the dishwasher still contains water after the programme has finished something may be blocking the drainage pump Such items are easily removed 1 Turn off the machine using the main power switch and unplug it from the wall socket 2 Remove the coarse filter and the fine filter 3 Scoop out the water from the dishwasher tub 4 In order to inspect the drainage pump remove the coloured stop on the right in the bottom drain 5 Turn the pump wheel located behind the drainage pump stop by hand Carefully remove any items 6 Refit the drainage pump stop along with the fine and coarse filters 7 Plug the machine in again If the dishwasher still does not start and a whirring sound is heard the overflow protection has been activated Shut off the water Remove the plug from the wall socket Call the service department Drainage pump stop NOTE Do not forget to refit the drainage pump stop Unblocking the inlet hose filter If the water supply contains small particles the outer filter on the inlet hose may become blocked which results in Water inlet fault 1 Turn off the machine using the main power switch and unplug it from the wall socket 2 Turn off the water tap 3 Unscrew the inlet hose 4 Carefully remove the outer filter from the inlet hose and clean it 5 Refit the filter and check that the gasket is correctly positioned 6 Screw the inlet hose firmly into place 7 Plug the machine into the wall socket and turn on the water tap Allow the pressure to settle for a while and check that the connection is watertight Outer filter on inlet hose Gasket
• Page 16 - English - : Troubleshooting ActionType of fault on the display Clear the drainage pump See the chapter Care and cleaning If the problem persists call the service department Overfilling water 1F10 See Water remains in the dishwasher in the table Problem below If the problem persists call the service department Water outlet faultF11 Check whether dishwasher inlet hose is connected to a pressure limiting valve some pressure limiting valves may restrict the supply of water to the dishwasher Water inlet faultF12 Check that the water tap is on Check that the outer filter on the inlet hose is not blocked See Unblocking the inlet hose filter in the chapter Care and cleaning If the problem persists call for service Turn off the water tap and call the service departmentInlet valve leakageF40 Clean the coarse and fine filters Check that the outer filter on the inlet hose is not blocked If the problem persists call the service department Water level faultF52 Turn off the water tap and call the service departmentOverfilling water 2F54 Call the service departmentCirc pump faultF56 Press any button to clear the error message ActionPossible causesProblem Open the door The main power switch only works when the door is open The door is closedPressing the main power switch has no effect Wait a moment then try againYou have pressed the buttons too soon after opening the door The buttons do not react when pressed See the chapter SettingsChild lock button lock activated Clean with a dry or slightly damp clothThe buttons are dirty Check that the baskets are correctly positioned horizontally The baskets are not correctly positionedCannot close door Check that the dishes are not blocking the baskets from sliding properly into place Press and hold StartStop until the display shows quotProgram startedquot The StartStop start button has not been pressed for long enough The dishwasher does not start CheckThe door is not properly closed Close the door and wait After a while the dishwasher continues the program You have opened the dishwasher to add more dishes while a program is in progress CheckA fusecircuit breaker has been tripped CheckThe plug is not plugged into the wall socket CheckThe water tap is turned off CheckOverflowleaks Turn off the water tap Pull out the plug and call the service department A whirring sound the drainage pump is heard from the dishwasher and does not stop when the main power switch is turned off Press and hold StartStop for three seconds if you want to cancel the Delayed Start option Check that the Delayed Start option has not been selected
• Page 17 - English - : ActionPossible causesProblem Check that the dishes are not blocking the spray arms The spray arms do not rotateThe dishes are not clean Clean the spray arms See Chapter Care and cleaning Spray arm holes or bearings blocked Choose a longer programmeUnsuitable dishwashing program Dose according to water hardness Far too much or far too little detergent results in poorer dishwashing results Incorrect detergent dosage Avoid large packagesOld detergent Detergent is a perishable product Do not cover porcelain with large bowls or the like Avoid placing very tall glasses in the corners of the baskets Dishes loaded incorrectly Place dishes to sit steadyGlasses and cups have toppled over during the program Check that the filter handle is locked in the stop position The handle should point towards the back of the dishwasher The filters are not fitted correctly Check that the coloured stop on the right in the bottom drain is in place See the chapter Care and cleaning Drainage pump stop missing Rinse off these types of foodstuffs if not starting the dishwasher immediately Use the Rinse amp hold program Some foodstuffs such as mustard mayonnaise lemon vinegar salt and dressings can mark stainless steel if left for too long Spots on stainless steel or silver In order to avoid marks and tarnishing separate dishes made from different metals such as silver stainless steel and aluminium All stainless steel can cause spots on silver if they come into contact during dishwashing Aluminium can also cause spots on dishes See the chapter SettingsIncorrect rinse aid dosage settingSpots or films on the dishes Wash crystal at a low temperature and with a conservative amount of detergent Contact the detergent manufacturer Too high temperature andor too much detergent can cause etching on crystal Unfortunately this cannot be repaired only prevented Reduce the dosage See the chapter Settings If you have very soft water you may want to dilute the rinse aid 5050 with water Rinse aid dosage setting too highThe dishes have a sticky whiteblue film Use a detergent with a bleaching agentLipstick and tea can be difficult to wash offSpots left after washing The detergent compartment must be dry when adding detergent The detergent compartment was damp when adding detergent Detergent residue in the detergent compartment after dishwashing Check that the dishes are not preventing the detergent compartment from opening The detergent compartment is blocked Check that the dishes are placed securely Spin the spray arms to make sure they can rotate The dishes are not correctly placed or the spray arms are not rotating Rattling sound when dishwashing No action The programme time is stored and next time the programme is run the corrected time will be displayed The program is taking longer than estimated1 minute appears in the display
• Page 18 - English - : ActionPossible causesProblem Clean the coarse and fine filtersThe filters are blockedWater remains in the dishwasher Check that the filter handle is locked in the stop position The handle should point towards the back of the dishwasher The filters are not fitted correctly Clean the drainage pump See the chapter Care and cleaning Debris in the drainage pump Check that the coloured stop on the right in the bottom drain is in place See the chapter Care and cleaning Drainage pump stop missing Check that the hose is free from kinks and sharp bends Kink in drainage hose Disconnect the drainage hose where it connects to the sink units water trap Check that no debris has fastened and that the connection has an inner diameter of at least 14 mm Blocked drainage hose Clean with washingup brush and low foaming cleaner Dirt around the seals and in cornersBad odour in dishwasher Run a program with a higher temperature once or twice a month Low temperature programs have been selected for a prolonged period Activate the Extra Dry optionDepending on the load the programmes drying cycle may be insufficient The dishes are not dry enough Fully load the dishwasherThe dishwasher is not fully loaded Top up with rinse aid or increase the rinse aid dosage level See the chapter Settings Rinse aid needs topping up or dosage is set too low Open the door a little once the program has finished
• Page 19 - English - : Technical information Information on energy labelling Energy labelling ASNZS 2007Australian standard 14Number of place settings Eco 1 no optionsDishwashing programs 235 hoursminutesProgram time Cold water 20 CConnection IEC 6070423Test method for noise measurement 1 This dishwashing program is the standard cleaning cycle used to compile the energy labelling information It is intended for washing normally dirty dishes and is the most effective program in terms of combined energy and water consumption Technical data 819872 mmHeight 596 mmWidth 559 mmDepth 45 kg 1 Weight 00310 MPaWater pressure See compliance plateElectrical connection See compliance plateRated power 1 Weight can vary due to different specifications
• Page 20 - English - : Installation 819 872 131186 50 3094 mm Nominal dimensions Actual measurements may vary Remove locking nuts for an installed height of 820821 mm Safety instructions Connections to electricity water and drainage must be performed by a qualified professional Always follow applicable regulations for water drainage and electricity Take care during installation Wear protective gloves There must always be two people Before screwing the dishwasher into place test the dishwasher by running the Rinse amp hold program Check that the dishwasher fills with water and drains Check also that none of the connections leak WARNING Turn off the water supply when installing the dishwasher The plug must be disconnected or power to the socket turned off while the work is carried out Transport protection for the door Do not forget to remove the transport protection for the door when unpacking the dishwasher REMOVE Placing the dishwasher The dishwasher can be installed builtin completely freestanding or partially builtin A Builtin The dishwasher is intended for installation under a worktop The recess dimensions are illustrated Holes for wirescables need not be larger than 38 mm in diameter Make sure the edges of such holes are even to prevent damage to the drainage and inlet hoses and the power cable Ø 38 820875 gt 560 mm
• Page 21 - English - : If the dishwasher is builtin the surrounding cabinetry must be resistant to any condensation from the dishwasher B Freestanding A freestanding dishwasher must be fitted with antitip brackets This comprises two brackets which are screwed into place as illustrated The dishwasher is then pushed in so that the brackets engage the rear feet Now the dishwasher will not topple if pressure is put on the open door If the dishwasher is installed completely on its own side panels and a worktop must both be fitted Accessories can be purchased where you bought the dishwasher WARNING A completely freestanding dishwasher must be fitted with antitip brackets C Partially builtin If the dishwasher is located so that one of its sides is visible a side panel must be fitted Accessories can be purchased where you bought the dishwasher Affix the protective film Attach the protective film packed in the document bag to the underside of the worktop The protective film is to protect the worktop from moisture NOTE The surface to which the protective film is affixed must be clean and dry Adjust the height and slide the dishwasher into place 1 Start by measuring the height from the floor to the bottom edge of the worktop 2 Measure the height from the floor to the top edge of the dishwasher 3 Lean the dishwasher forwards a little and adjust the rear foot with the screw at the front of the dishwasher Turn clockwise to lower or anticlockwise to raise Max 06 Nm 5 Adjust the front feet by turning them clockwise to raise and anticlockwise to lower the dishwasher 2x 24 mm 16 mm 6 Check that there is an air gap of at least 3 mm between the underside of the worktop and the top edge of the dishwasher 7 Slide the dishwasher into place Pull through the drainage and supply hoses when the machine is slid into place Check that the hoses have no kinks or sharp bends and check that there is nothing that can damage the hoses 8 Make any final adjustments to the feet the dishwasher may lean no more than 5 mm and tighten the lock nuts on the front feet
• Page 22 - English - : Drainage connection This dishwasher is suitable for installing in a raised recess to attain an ergonomic working height This means that the dishwasher can be placed so that the drainage hose runs to a lower level than the bottom of the dishwasher such as by routing it directly to a floor drain The dishwasher is fitted with an integrated antisiphon device to prevent the machine from being emptied of water during the wash cycle min 14 mm Max 950 mm The drainage hose can also be connected to a connection nipple on the sink units water trap The connection nipple must have an internal diameter of at least 14 mm The drainage hose may be extended by a maximum of 25 m the total length of the drainage hose must not exceed 45 m Any joins and connecting pipes must have an internal diameter of at least 14 mm However the drainage hose should ideally be replaced with a new hose without joins No part of the drainage hose may be more than 950 mm above the bottom of the dishwasher Attach the drainage hose with a hose clamp Ensure that the drainage hose has no kinks Connection to water supply Use only the inlet hose supplied with the dishwasher Do not reuse old or other spare hoses The supply pipe must be fitted with a water tap stopcock The water tap must be easily accessible so that the water can be shut off if the dishwasher has to be moved Once the installation is complete turn on the water tap and allow the pressure to settle for a while Check that all connections are watertight Connection to cold water supply Connect the dishwasher to the cold water supply if the building is heated using oil electricity or gas Connection to hot water supply Connect the dishwasher to the hot water supply max 70 C if the building is heated using an energyefficient means such as district heating solar power or geothermal power Choosing a hot water connection cuts dishwashing times and reduces the dishwashers energy consumption NOTE Do not exceed the permitted water supply temperature Certain materials used in some cookware cannot withstand high heat See Fragile dishes in the chapter Loading the dishwasher NOTE The water pressure must be between 003 and 10 MPa Connecting a dishwasher to the water supply via certain types of pressure limiting valves may restrict the water supply This may cause the error message Water inlet fault to be displayed If the water pressure is higher than 10 MPa a pressure limiting valve must be fitted Electrical connection Information about the electrical connection can be found on the compliance plate This specification must match the electricity supply The dishwasher must be connected to an earthed wall socket The electric wall socket must be placed outside of the installation area to be easily accessible after installing the dishwasher Do not use an extension cord NOTE Repairs and maintenance must be carried out by a qualified professional
• Page 23 - English - : Screwing the dishwasher into place Applicable only to builtin dishwashers 2x After fastening the machine check that the front feet still touch the floor Screw the dishwasher into place with two extra screws If there is an air gap of more than 3 mm between the underside of the worktop and the top of the dishwasher the dishwasher should be screwed into place with two extra screws 2x KNOCK OUT Dishwasher kick panel The dishwasher is supplied with a kick panel Install the sound insulation only certain models x x x Install the kick panel 2x
• Page 24 - English - : ASKO Service Information about your product There is a QR code on the compliance plate Scan the code to view information about your product Contact the service department Read the chapter Troubleshooting before contacting the service department If you have encountered a problem that you cannot resolve please contact your nearest dealer see wwwaskocom When making contact provide the details on the serial number plate Include the article number 1 and the serial number 2 SERIAL NO ART NO QR code Information for test institute Request test institute information via email dishwashersappliancedevelopmentcom The request should include the details on the products serial number plate Include the article number 1 and the serial number 2 SERIAL NO ART NO
• Page 28 - English - : Quick guide Load the baskets See page 5 Do not rinse dishes under running water before loading them in the dishwasher Simply scrape off large food particles before loading the dishwasher Check that the spray arms can rotate freely Check also that the water tap is on Dont forget Empty the coarse filter and clean the fine filter when necessary See page 14 Add detergent The detergent compartment has one smaller compartment for the prewash and one for the main wash See page 8 Open the door and press the main power switch close the door CheckAdd rinse aid Use rinse aid to achieve good washing and drying results See page 4 Refill rinse aid indicator Select a program a program mode and any options See page 9 Press StartStop Art No 793289 Rev 02 We reserve the right to make changes ASKO APPLIANCES SOCKERBRUKSGATAN 3 SE531 40 LIDKÖPING SWEDEN WWWASKOCOM en 1019