Verve
®
Irons
Instruction Booklet
This book covers the use and care of the following Verve
™
Irons:
SR6585 Verve
®
58 Platinum Shot & Spray Iron with Safety Auto-Off
SR6575 Verve
®
57 Platinum Shot & Spray Iron with Safety Auto-Off
SR6565 Verve
®
56 Platinum Shot & Spray Iron with Safety Auto-Off
Please read these instructions carefully
and retain for future reference.
Sunbeam’s Safety Precautions 3
Features of your Verve Iron 4
Using your Verve Iron 6
The Safety Auto-Off Feature 7
Care and Cleaning of your Verve Iron 8
Ironing Tips & Tricks 9
Ironing Chart 10
Contents
Important instructions – retain
for future use.
3
Sunbeam’s Safety Precautions
Sunbeam is very safety conscious when
designing and manufacturing consumer
products, but it is essential that the product user
also exercise care when using an electrical
appliance. Listed below are precautions which
are essential for the safe use of an electrical
appliance:
• Readcarefullyandsavealltheinstructions
provided with an appliance.
• Alwaysturnthepoweroffatthepoweroutlet
before you insert or remove a plug. Remove
by grasping the plug - do not pull on the cord.
• Turnthepoweroffandremovetheplug
when the appliance is not in use and before
cleaning.
• Donotuseyourappliancewithanextension
cord unless this cord has been checked
and tested by a qualified technician or
service person.
• Alwaysuseyourappliancefromapower
outlet of the voltage (A.C. only) marked
on the appliance.
• Thisapplianceisnotintendedforuseby
persons (including children) with reduced
physical, sensory or mental capabilities, or
lackofexperienceandknowledge,unlessthey
have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
• Childrenshouldbesupervisedtoensurethat
they do not play with the appliance.
• Thetemperatureofaccessiblesurfacesmaybe
high when the appliance is operating.
• Neverleaveanapplianceunattendedwhile
in use.
• Donotuseanapplianceforanypurpose
other than its intended use.
• Donotplaceanapplianceonornearahotgas
flame, electric element or on a heated oven.
• Donotplaceontopofanyotherappliance.
• Donotletthepowercordofanappliancehang
over the edge of a table or bench top or touch
any hot surface.
• Donotoperateanyelectricalappliancewith
a damaged cord or after the appliance has
been damaged in any manner. If damage is
suspected, return the appliance to the nearest
Sunbeam Appointed Service Centre
forexamination,repairoradjustment.
• Foradditionalprotection,Sunbeam
recommend the use of a residual current
device(RCD)withatrippingcurrentnot
exceeding30mAintheelectricalcircuit
supplying power to your appliances.
• Donotimmersetheapplianceinwater
or any other liquid unless recommended.
•Appliancesarenotintendedtobeoperated
bymeansofanexternaltimerorseparate
remote control system.
•Thisapplianceisintendedtobeusedin
household and similar applications such
as: staff kitchen areas in shops, offices and
other working environments; farm houses; by
clients in hotels, motels and other residential
type environments; bed and breakfast type
environments.
SAFETYPRECAUTIONSFORYOURIRON
• Donotleaveahotironwithinreachof
children. If they come into contact with a
hot iron it could lead to serious burns.
• Irononlyonanironingboard.
• Anirontakesapproximately30minutesto
cool down. Allow the iron to cool completely
before storing.
• Donotwindthecordaroundthesoleplate
while the iron is still hot.
• Donotleavetheironunattendedwhileitis
plugged into the power outlet.
• Alwaysunplugtheironfromthepoweroutlet
before filling or emptying the water tank.
• Theironmustbeusedandrestedonastable
surface.
• Theironisnottobeusedifithasbeen
dropped, if there are visible signs of
damage or if it is leaking.
If you have any concerns regarding the performance and use of your appliance,
please visit www.sunbeam.com.au or contact the Sunbeam Consumer Service Line.
Ensure the above safety precautions are understood.
4
Features of your Sunbeam
Verve Iron
Powerful shot of steam
Pressing the shot of steam button instantly
produces a powerful shot of steam to remove
stubborn wrinkles.
Vertical shot of steam
Pressing the shot of steam button with the iron
in an upright position produces a vertical shot of
steam, which is ideal for steaming curtains and
suits, and removing creases from delicate fabrics.
Fine spray mist
Pressing the spray button provides a fine mist
spray to dampen hard-to-iron fabrics.
Easy-fill water inlet
Holds 300ml of water for continual high steam
performance without having to refill the tank
regularly.
Drip-stop steam system
The drip-stop steam system automatically stops
water flowing to the steam chamber should the
temperature fall too low to generate steam.
This prevents dripping, even at low
temperatures.
Full length button groove
For ironing around buttons.
2400 watts for fast heat up
Provides faster initial heat up and rapid heat
recovery during ironing. The 2400W element
helps to maintain your selected temperature,
and provides superior shot of steam output.
Teflon
®
Platinum Pro non-stick soleplate
Teflon
®
Platinum Pro is DuPont’s premium non-stick coating.
It glides easily across all types of fabric and prevents
sticking. This hard wearing surface consists of a unique three
coat system for superior durability and scratch resistance. It
simply wipes clean for fuss free maintenance.
Safety auto-off
The iron automatically switches itself off if
left in the ironing position (horizontal) for 30
seconds, or in the heel rest position (vertical)
for 15 minutes. (For more information on the
safety auto off feature see page 7).
Power light
Illuminates to indicate that the iron is
connected to the power outlet and the power
is turned on.
Thermostat light
Illuminates to indicate that the iron is
heating and goes out when it has reached the
temperature selected on the temperature dial.
The thermostat light cycles on and off during
ironing as the iron maintains the selected
temperature.
Stable heel rest
Extra large heel rest keeps the iron stable on
the ironing board.
Cord wrap
The built-in cord wrap facility allows you to
wind the cord around the heel for neat and
tidy storage of the cord when the iron is not
in use.
Concentric steam and temperature dials
The steam and temperature dials are
positioned together for easy adjustment.
Variable steam dial
Allows you to select the desired steam output
for each garment. Alternatively, select the DRY
setting to iron without steam.
Temperature dial
Allows you to select the desired temperature
for each garment. The adjustable temperature
dial also indicates the amount of steam
recommended for use on each temperature
setting.
SR 6000 SERIES DIAL GRAPHICS.
Steam Dial
Temperature Dial
5
Powerful shot of steam
Pressing the shot of steam button instantly
produces a powerful shot of steam to remove
stubborn wrinkles.
Vertical shot of steam
Pressing the shot of steam button with the iron
in an upright position produces a vertical shot of
steam, which is ideal for steaming curtains and
suits, and removing creases from delicate fabrics.
Fine spray mist
Pressing the spray button provides a fine mist
spray to dampen hard-to-iron fabrics.
Easy-fill water inlet
Holds 300ml of water for continual high steam
performance without having to refill the tank
regularly.
Drip-stop steam system
The drip-stop steam system automatically stops
water flowing to the steam chamber should the
temperature fall too low to generate steam.
This prevents dripping, even at low
temperatures.
Full length button groove
For ironing around buttons.
2400 watts for fast heat up
Provides faster initial heat up and rapid heat
recovery during ironing. The 2400W element
helps to maintain your selected temperature,
and provides superior shot of steam output.
Teflon
®
Platinum Pro non-stick soleplate
Teflon
®
Platinum Pro is DuPont’s premium non-stick coating.
It glides easily across all types of fabric and prevents
sticking. This hard wearing surface consists of a unique three
coat system for superior durability and scratch resistance. It
simply wipes clean for fuss free maintenance.
Safety auto-off
The iron automatically switches itself off if
left in the ironing position (horizontal) for 30
seconds, or in the heel rest position (vertical)
for 15 minutes. (For more information on the
safety auto off feature see page 7).
Power light
Illuminates to indicate that the iron is
connected to the power outlet and the power
is turned on.
Thermostat light
Illuminates to indicate that the iron is
heating and goes out when it has reached the
temperature selected on the temperature dial.
The thermostat light cycles on and off during
ironing as the iron maintains the selected
temperature.
Stable heel rest
Extra large heel rest keeps the iron stable on
the ironing board.
Cord wrap
The built-in cord wrap facility allows you to
wind the cord around the heel for neat and
tidy storage of the cord when the iron is not
in use.
Concentric steam and temperature dials
The steam and temperature dials are
positioned together for easy adjustment.
Variable steam dial
Allows you to select the desired steam output
for each garment. Alternatively, select the DRY
setting to iron without steam.
Temperature dial
Allows you to select the desired temperature
for each garment. The adjustable temperature
dial also indicates the amount of steam
recommended for use on each temperature
setting.
SR 6000 SERIES DIAL GRAPHICS.
Steam Dial
Temperature Dial
Before first use
Remove any adhesive stickers, plastic covers
or cardboard sleeves from the soleplate.
Ensurethatalladhesiveisremovedby
rubbing the soleplate with a cloth
dampened with methylated spirits.
Fillthewatertankandemptythewater.This
will rinse out any foreign particles remaining
in the water tank from the manufacturing
process.
NOTE: When turned on for the first time,
your new iron may give off vapours for up
to10minutes.Thisisduetotheinitial
heating of the materials used. It is safe, not
detrimental to the performance of the iron,
and will not reoccur.
Filling the iron with water
Before filling the iron with water ensure the
power is turned off and the plug is removed
from the power outlet. The iron can be filled
with water while it is hot.
Place the iron on its heel and open the water
inlet cover.
Slowly pour water into the water inlet until
themaximumwaterlevelisreached.Donot
exceedthemaximumwaterlevelindicator.
Push the water inlet cover firmly to close.
NOTE: The special soleplate design allows you
to use tap water with your Verve iron without
affecting the steam performance. However in
very hard water areas, Sunbeam recommends
the use of distilled water, or water which has
been demineralised.
Forbestperformance,werecommend
theuseofSunbeamWaterDemineraliser,
available from selected retailers. This will
produceupto30litresofdemineralised
water.
Donotfilltheironwithfabricconditioner,
starches or any other solution as these will
damagethesteammechanism.Donotuse
contaminated water.
Using your iron
1.Inserttheplugintoa230/240voltpower
outlet and turn the power on. The power
ONlight(positionedontopofthehandle)
will illuminate to indicate that the iron is
switched on and heating.
2. Turn the temperature dial to the desired
setting by aligning the setting on the
dial with the temperature indicator. The
thermostat light will illuminate to indicate
that the iron is heating to the selected
temperature. When the thermostat light
goes out the iron has reached the selected
temperature and is ready to use.
NOTE: When the temperature dial is changed
from a high setting to a lower temperature
setting during ironing, the thermostat light
will go out immediately. This indicates
that the iron is cooling to the selected
temperature. To ensure that the iron has
reached the selected temperature and is not
too hot, wait until the thermostat light comes
on again and then goes out before ironing.
Steam ironing
Followsteps1and2above.
NOTE: When steam ironing, ensure that the
temperature dial is set to any temperature
within the steam band, and that the tank is
atleast1/4fullofwater.
3.Turn the steam dial to the desired steam
setting.
Forbestresults,selectthesteamsettingthat
corresponds to the selected temperature, as
indicated on the temperature dial.
6
Using your Sunbeam Verve Iron
Steam
Temperature
Dry ironing
Followsteps1and2above.
3.SelectDRYonthesteamdial.
This will cut off the steam flow if there
is water in the tank.
Using the shot of steam
The shot of steam can be used when dry
or steam ironing, when the temperature dial
is set to any temperature within the steam
bandorabovethetwodot(••)setting.
1.Ensurethetankisatleast1/4fullof
water.
2. Select the desired temperature and wait
until the thermostat light goes out.
3.Presstheshotofsteambuttonseveral
times with the iron on the soleplate to
prime the pump.
NOTE: If the tank has run dry, it may be
necessary to re-prime the pump after filling
the iron with water.
Using the spray mist
The spray mist can be used whether dry or
steam ironing to pre-dampen hard to iron
fabrics.
1.Ensurethetankisatleast1/4fullof
water.
2. Press the spray button during ironing to
release a fine mist from the spray nozzle.
The safety auto-off mechanism automatically
turns the iron off if you forget.
The iron will automatically shut off if left
on the heel rest (vertical) for 15 minutes,
orintheironingposition(horizontal)for30
seconds, without being moved.(See figure 2).
The thermostat and power lights on the
handle will flash to let you know that you
have left the iron unattended.
Power to the iron's heating element will be
cut.
Once the iron is moved the power will
reconnect. Allow the iron to heat until the
thermostat light goes out, and continue
ironing as normal.
7
Using your Sunbeam Verve Iron (continued)
The safety auto-off feature
Figure 2
15 minutes 30seconds
After each use
1 Turn the power off and remove the plug
from the power outlet.
2 Allow the iron to cool before winding
the cord around the built-in cord wrap.
Storage
Always store the iron on its heel rest.
Donotstoretheironwiththesoleplate
facing down, or in the carton.
Cleaning
Tocleantheexteriorofyouriron,wipe
over with a damp soft cloth and wipe dry.
Caution:Donotuseharshabrasives,
chemical cleaners or solvents to clean the
exteriorofyourironasthesewilldamagethe
surface.
Cleaning the steam holes
To remove build up from the steam holes
which may affect steam performance,
use a cotton wool tip moistened in
methylated spirits.
Cleaning the Teflon
®
Platinum Pro
non-stick soleplate
The non-stick coating reduces sticking
of fabrics and starches to the soleplate.
Donotironoversharpobjectssuchas
buttons, studs and zippers, as these will
scratch the surface.
Wipe the soleplate with a damp soft cloth
after each use. If polyester has burnt to the
soleplate, iron a damp cotton cloth while hot.
Caution:Donotusescouringpads,abrasives
or harsh cleaners to clean your Teflon
®
Platinum Pro soleplate, as these will scratch
and damage the surface.
8
Care and Cleaning
Tip # 27 - Iron shirts like a pro
Start with the collar, working from the outer
edges into the middle. Iron the shoulder
next,followedbythecuffsandsleeves.
Place the collar at the narrow end of the
board so that one front panel of the shirt
isextendedflat.Ironthefrontpanelfrom
shoulder to shirt tail. Rotate to iron the
back of the shirt. Rotate and complete the
remaining front panel.
Tip # 34 - Tips for T-shirts
Straighten seams on t-shirts before hanging
out to dry. To avoid damage to printed
graphics and logos turn the t-shirt inside out
andironthereversesideoftheprint.Never
iron areas of your t-shirt where perspiration
marks are visible as the heat of the iron will
permanentlyfixthestain.
Tip # 54 - Hung out to dry
When washing is complete, remove shirts
from the machine immediately, shake them
out and hang them on coat hangers to air dry
– this will keep wrinkles to a minimum.
Tip # 18 - Selecting the right temperature
If you are unsure of the correct setting for a
particular garment, test a small area such as
a seam or inside hem before ironing a visible
area. Start with a low temperature and slowly
increase the heat to find the best setting.
Tip # 33 - Don’t be afraid to iron silk
Don’tbeafraidtoironsilk.Althoughdelicate
in appearance, silk is the strongest and most
resilient of all natural fibres. To achieve the
best results, set to a low cotton setting and
use regular shots of steam. Always use a
pressing cloth to avoid shine marks.
Tip # 13 - Ironing the seam
Always press seams in the same direction
they were made. When a garment is
produced, the fibres will naturally settle
in the direction they were initially pressed,
soit’sbestnottoironagainstthegrain.
Tip # 26 - Sort types of fabric
Sort articles to be ironed according to the
type of fabric. This will reduce the need to
adjustthetemperatureconstantly.Startwith
articles requiring lower temperatures and
work your way through to items requiring
higher settings.
Tip # 2 - Summer frocks and frills
Steam is the key when ironing delicate
summer fabrics such as muslin, cotton and
linen.Don’tpressdownwiththeiron,simply
hover above the garment and steam it using
a vertical shot of steam. Ruffling, netting,
tulle or intricate hand detailing is also best
ironed using this method.
Tip # 5 - Pressing your winter woollies
Steam is crucial when pressing your winter
woollies. Woollen garments can be hung and
steamed using the vertical shot of steam
feature. After steaming, brush the garment
with your hand to plump up woollen fibres.
If ironing the garment flat it is best to use
apressingcloth.Don’tbeafraidtoapply
pressure – steam and hold.
Tip # 42 - Table settings to impress
To avoid unwanted creases always iron
your table cloth after taking it out of the
cupboard. A dinner party is a special
occasion, so treat the table cloth as you
wouldyourownoutfit.Forbestresults,lay
towels across your table and iron the table
cloth over the towels. This will save you time
and ensure a beautifully presented table
setting.
9
Ironing Tips and Tricks
Ironing Chart
Fabric Temp setting Ironing Ironing recommendation
Acrylic
MINIMUM
Minto•
Dryirononreversesideoffabric
Acetate
MINIMUM
Minto•
Dryirononreversesideoffabric
while still damp
Nylon
MINIMUM
Minto•
Iron on reverse side of fabric
Polyester
SYNTHETIC
•
Iron on reverse side of fabric
Rayon
SYNTHETIC
•
Iron on reverse side of fabric
Viscose
SYNTHETIC
•
Mainly dry iron. Steam can be used under
manufacturer's instructions
Silk
SILK
••
Irononreversesideoffabric.Useanironing
cloth to prevent shine marks
and use regular shots of steam
Cotton Blends
WOOL
••
Checklabelandfollowmanufacturer’s
instructions.Usesettingforthefibre
requiring the lowest setting
Wool
WOOL
••
Steam iron on reverse side of fabric
or use an ironing cloth. Brush gently
to raise the fibres
Wool Blends
WOOL
••
Steam iron on reverse side of fabric
or use an ironing cloth. Brush gently
to raise the fibres
Corduroy
COTTON
•••
Steam iron on reverse side of fabric
or use an ironing cloth. Brush gently
to raise the fibres
Cotton
COTTON
•••
Steam iron while still damp or use spray
todampen.Usemediumtohighsteam
Linen
LINEN
•••toMax
Iron on reverse side of fabric or use an
ironing cloth to prevent shine marks,
especially with dark colours. Iron while
still damp or use spray to dampen.
Usemediumtohighsteam
Denim
MAXIMUM
•••toMax
Iron while still damp or use spray
todampen.Usemaximumsteam
10
Shouldyouexperienceanydifficultieswith
your appliance, please phone our customer
servicelineforadviceon1300881861in
Australia,or0800786232inNewZealand.
Alternatively, you can send a written claim
to Sunbeam at the address listed below.
On receipt of your claim, Sunbeam will
seek to resolve your difficulties or, if the
appliance is defective, advise you on how
to obtain a replacement or refund.
YourSunbeam2YearReplacement
Guarantee naturally does not cover misuse
or negligent handling and normal wear and
tear.
Similarlyyour2YearReplacementGuarantee
does not cover freight or any other costs
incurred in making a claim. Please retain
your receipt as proof of purchase.
The benefits given to you by this guarantee
are in addition to your other rights and
remedies under any laws which relate to the
appliance.
Our goods come with guarantees that cannot
beexcludedundertheAustralianConsumer
LawandundertheNewZealandConsumer
Guarantees Act.
In Australia you are entitled to a
replacementorrefundforamajorfailureand
for compensation for any other reasonably
foreseeablelossordamage.Youarealso
entitled to have the goods repaired or
replaced if the goods fail to be of acceptable
quality and the failure does not amount to
amajorfailure.
Should your appliance require repair or
service after the guarantee period, contact
your nearest Sunbeam service centre.
ForacompletelistofSunbeam’sauthorised
service centres visit our website or call:
Australia
www.sunbeam.com.au
1300881861
Units5&6,13LordStreet
BotanyNSW2019Australia
New Zealand
www.sunbeam.co.nz
0800786232
26VesteyDrive,MtWellington
Auckland,NewZealand
In the unlikely event that this appliance develops any malfunction
within 2 years of purchase (3 months commercial use) due to
faulty materials or manufacture, we will replace it for you
free of charge.
2 Year Replacement Guarantee
is a registered trademark.
Need help with your appliance?
Contact our customer service team or visit
our website for information and tips on
getting the most from your appliance.
In Australia
Visit www.sunbeam.com.au
Or call 1300 881 861
In New Zealand
Visit www.sunbeam.co.nz
Or call 0800 786 232
‘Verve’ and ‘Resilium’ are registered trademark
of Sunbeam Corporation.
‘Teflon’ is a registered trademark of DuPont.
Designed and engineered in Australia
Made in China.
Due to minor changes in design or otherwise,
the product may differ from the one shown in this leaflet.
© Copyright.
Sunbeam Corporation Limited 2010.
ABN 45 000 006 771
Units 5 & 6, 13 Lord Street
Botany NSW 2019 Australia
Unit 3, Building D
26 Vestey Drive
Mt Wellington Auckland
New Zealand
Sunbeam Corporation is a division of GUD Holdings Ltd.
6/11
