Loading ...
Loading ...
Loading ...
22
First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,
refer to the warranty, or visit http://www.kitchenaid.com/customer-service. In Canada, visit http://www.kitchenaid.ca.
Contact us by mail with any questions or concerns at the address below:
In the U.S.A.:
KitchenAid Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
Please include a daytime phone number in your correspondence.
In Canada:
KitchenAid Brand Home Appliances
Customer eXperience Centre
200 - 6750 Century Ave.
Mississauga, Ontario L5N 0B7
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSES AND/OR SOLUTIONS
Nothing will operate Power supply cord is unplugged - Plug into a grounded outlet.
ENERGY SAVE is active, and the display is blank - Press any keypad on the control to display the
time of day. See the “Electronic Oven Controls” section for more information.
Household fuse is blown or a circuit breaker is tripped - Replace the fuse or reset the circuit breaker.
If the problem continues, call an electrician.
The control displays an F9 or F9 E0 error code - The electrical outlet in the home may be miswired.
Contact a qualied electrician to verify the electrical supply.
Surface burners will not
operate
The control knob is not set correctly - Push in knob before turning to a setting.
Air in the gas lines - If this is the rst time the surface burners have been used, turn on any one of the
surface burner knobs to release air from the gas lines.
Clogged burner ports - See the “Sealed Surface Burners” section.
Surface burner flames are
uneven, yellow and/or
noisy
Clogged burner ports - See the “Sealed Surface Burners” section.
Burner caps positioned improperly - See the “Sealed Surface Burners” section.
Range converted improperly - If propane gas is being used, contact a service technician or see
“Warranty” for contact information.
Excessive heat around
cookware on cooktop
Cookware and flame are not matched - The cookware should be centered above the burner with the
bottom sitting level on the grate. The ame should be adjusted so that it does not extend up the sides of
the pan.
Cooktop cooking results
not what expected
Improper cookware - Ideal cookware should have a at bottom, straight sides and a well tting lid, and
the material should be of a medium to heavy thickness.
Control knob set to incorrect heat level - See the “Cooktop Use” section.
Range is not level - Level the range. See the Installation Instructions.
Oven will not operate Delay Start is set - See the “Cook Time” section.
Control is locked - Press and hold START for 3 seconds to unlock.
The range is in Demo mode - Demo mode will deactivate all oven elements. See “Demo Mode” in the
“Electronic Oven Controls” section.
Electronic oven control set incorrectly - See the “Electronic Oven Controls” section.
Oven temperature too high
or too low
Oven temperature needs adjustment - See “Oven Temperature Control” in the “Electronic Oven
Controls” section.
Display shows messages Power failure (display shows flashing time) - Clear the display. On some models, reset the clock, if
needed. See “Clock” keypad feature in the “Feature Guide” section.
Error code (display shows letter followed by number) - Depending on your model, press CANCEL to
clear the display. See “Control Display” in the “Electronic Oven Controls” section. If it reappears, call for
service. See the “Warranty” for contact information.
Start needs to be pressed so a cycle can begin (display shows “PUSH” or “PSH”) - See the “Start”
keypad feature in the “Feature Guide” section.
Range is in Sabbath mode (display shows “SAb”) - Press CANCEL to exit Sabbath mode.
Clean cycle did not work
on all spills
Several cooking cycles between Clean cycles or spills on oven walls and doors - Run additional
Clean cycles. Use the AquaLift
®
Technology Cleaning Kit. Affresh
®
Kitchen and Appliance Cleaner or
affresh
®
Cooktop Cleaner can be used for stubborn soils. See the “Accessories” and “Clean Cycle”
sections for more information.
Mineral deposits are left on
the oven bottom after the
Clean cycle
Tap water was used in the Clean cycle - Use distilled or ltered water in the Clean cycle.
To remove deposits, use a cloth soaked with vinegar. Then use a cloth dampened with water to
thoroughly remove any vinegar residue.
Range is not level - Mineral deposits will collect on dry areas of the oven bottom during the Clean
cycle. Level the range. See the Installation Instructions.
To remove deposits, use a cloth soaked with vinegar. Then use a cloth dampened with water to
thoroughly remove any vinegar residue.
Loading ...
Loading ...
Loading ...