Loading ...
Loading ...
Loading ...
4
■ The amount of detergent to use depends on:
How much soil remains on the items - Heavily soiled loads
require more detergent.
The hardness of the water - If you use too little in hard water,
dishes won't be clean. If you use too much in soft water,
glassware will etch.
Soft to Medium Water (0-6 grains per U.S. gallon)
[typical water softener water and some city water]
Medium to Hard Water (7-12 grains per U.S. gallon)
[well water and some city water]
■ Depending on your water hardness, fill the Main Wash section
of the dispenser as shown. Fill the Pre-Wash section to the
level shown, if needed.
NOTE: Fill amounts shown
are for standard powdered
detergent. Follow instructions
on the package when using
other dishwasher detergent.
Add Rinse Aid
■ Your dishwasher is designed to use rinse aid for good drying
performance. Without rinse aid your dishes and dishwasher
interior will have excessive moisture. The heat dry option will
not perform as well without rinse aid.
■ Rinse aid keeps water from forming droplets that can
dry as spots or streaks. They also improve drying by
allowing water to drain off of the dishes after the final
rinse.
■ Rinse aid helps to reduce excess moisture on the
dish racks and interior of your dishwasher.
■ Check the rinse aid indicator. Add rinse aid when indicator
drops to “Add” level.
■ To add rinse aid, turn the dispenser
cap to “Open” and lift off. Pour rinse
aid into the opening until the indicator
level is at “Full.” Replace the
dispenser cap and turn to “Lock.”
Make sure cap is fully locked.
NOTE: For most water conditions, the
factory setting of 2 will give good
results. If you have hard water or notice
rings or spots, try a higher setting. Turn
the arrow adjuster inside the dispenser
by either using your fingers or inserting
a flat-blade screwdriver into the center
of the arrow and turning.
Select a Cycle (cycles vary by model)
Press the Select Cycle button until the light below the desired cycle
is on.
NOTE: Heavier cycles and options affect cycle length. Some
cycles and options will take up to 3¹⁄₂ hours to complete.
Pots & Pans – Use for heavily
soiled, hard-to-clean items.
Normal – Use for normal food
soil. The energy usage label is
based on this cycle.
Eco– Use for lightly soiled items.
It saves energy.
1-hr Wash – Use for lightly soiled items. For fast results, 1-hr
Wash will clean the dishes using slightly more water and energy.
Rinse Only – (no options apply to this cycle) Do not use detergent.
This is only a rinse that keeps food from drying on your dishes and
reduces odor buildup in your dishwasher until you are ready to
wash a full load.
Select Options (options vary by model)
You can customize your cycles by pressing the options desired.
Repeatedly press the button until the
desired combination of options is
selected.
High Temp – (use only with Pots & Pans
and Normal wash cycles) Heats the water
during the wash portions of the cycle.
Sani Rinse – (use only with Pots & Pans
and Normal wash cycles) Select this
option to raise the water temperature in the final rinse to
approximately 155°F (68°C). Sani Rinse option adds heat and time
to the cycle. This high temperature rinse sanitizes your dishes and
glassware in accordance with NSF/ANSI Standard 184 for
Residential Dishwashers. Certified residential dishwashers are not
intended for licensed food establishments.
Heated Dry – (use only with 1-hr Wash, Pots & Pans and Normal
wash cycles) Use for best drying results. When selected with the
1-hr Wash cycle, the time is increased by approximately
30 minutes.
4-hr Delay – (any cycle) Offers the choice to start the dishwasher
automatically at a later time. Select a wash cycle and options.
Press 4-hr Delay. Press START/RESUME. Close the door firmly.
Lock – (on 4-hr Delay button) use to avoid
unintended use of your dishwasher. When Control
Lock is lit, all buttons are disabled. The dishwasher
door can be opened while the controls are locked.
To turn on Lock:
Press and hold 4-hr Delay for at least 3 seconds. The
Control Lock light glows. If you press any pad while
your dishwasher is locked, the light flashes 3 times.
To turn off Lock:
Press and hold 4-hr Delay for at least 3 seconds. The Control Lock
light turns off.
Start or Resume a Cycle
■ Run hot water at the sink nearest your dishwasher until the
water is hot. Turn off water.
■ Push door firmly closed. The door latches
automatically. Select the wash cycle and options
desired OR press START/RESUME to repeat the same
cycle and options as in the previous wash cycle.
■ You can add an item anytime before the main wash
starts. Open the door slowly and add the item. Close
the door firmly. Press START/RESUME.
■ Clean indicator glows when the cycle is finished.
Sanitized glows when Sani Rinse option is
selected and sanitization levels occur.
STEP 3
Soft Water
Hard Water
Soft Water
Hard Water
Main Wash Pre-Wash
Full
Add
¹⁄₄
turn to lock
Lock
Refill
6
5
4
3
2
-
-
-
max
fill
1
-
-
-
-
-
-
-
-
-
-
-
6
5
4
3
2
-
-
-
max
fill
1
-
-
-
-
-
-
-
-
-
-
-
-
STEP 4
Loading ...
Loading ...
Loading ...