TABLE OF CONTENTS
www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352
All about the
Use & Care
of your Beverage Cooler
Important Safety Instructions .................................2
Installation ...........................................................4
Door Reversal Instructions .....................................5
Energy Saving Tips ................................................6
242103100 (April 2010)
Temperature Controls ............................................7
Care and Cleaning .................................................8
Before you Call ..................................................... 9
Major Appliance Warranty ....................................11
2
SERIAL/MODEL #’S - IMpORtAnt SAfEty InStRuctIOnS
WARnInG
WARNING indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
IMpORtAnt
IMPORTANT indicates installation, operation or
maintenance information which is important but not
hazard-related.
DAnGER
DANGER indicates an imminently hazardous situation
which, if not avoided, will result in death or serious
injury.
This is the safety alert symbol. It is used to alert
you to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible injury
or death.
cAutIOn
CAUTION indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury.
WARnInG
Please read all instructions before using this Beverage
Cooler.
This Owner’s Guide provides specic operating
instructions for your model. Use your Beverage Cooler
only as instructed in this guide. These instructions are
not meant to cover every possible condition and situation
that may occur. Common sense and caution must be
practiced when installing, operating, and maintaining any
appliance.
Record the model and serial numbers in the space
provided below. The serial plate is located on the upper
left wall inside the cabinet.
WARnInG
Do not store or use gasoline, or other ammable
vapors and liquids in the vicinity of this or any other
appliance. Read product labels for ammability and
other warnings.
3
IMpORtAnt SAfEty InStRuctIOnS
WARnInG
Destroy carton, plastic bags, and any exterior
wrapping material immediately after the wine
cooler is unpacked. Children should never use
these items to play. Cartons covered with rugs,
bedspreads, plastic sheets or stretch wrap may
become airtight chambers, and can quickly cause
suffocation.
Remove all staples from the carton. Staples can
cause severe cuts, and destroy nishes if they
come in contact with other appliances or furniture.
An empty, discarded appliance is a very dangerous
attraction to children.
Remove the door(s) of any appliance that is not in
use, even if it is being discarded.
WARnInG
•
The power
cord of the appliance is equipped with a three-
prong grounding plug for your protection against
electrical shock hazards. It must be plugged
directly into a properly grounded three prong
receptacle. The receptacle must be installed in
accordance with local codes and ordinances.
Consult a qualied electrician. Avoid connecting
refrigerator to a Ground Fault Interruptor (GFI)
circuit.
If the power cord is damaged, it should be •
replaced by an authorized service technician to
prevent any risk.
Never unplug the appliance by pulling on the •
power cord. Always grip the plug rmly, and
pull straight out from the receptacle to prevent
damaging the power cord.
Unplug the appliance before cleaning and before •
replacing a light bulb to avoid electrical shock.
Performance may be affected if the voltage •
varies by 10% or more. Operating the unit with
insufcient power can damage the compressor.
Such damage is not covered under your warranty.
Do not plug the appliance into an electrical outlet •
controlled by a wall switch or pull cord to prevent
the appliance from being turned off accidentally.
WARnInG
Child entrapment and suffocation are not problems
of the past. Junked or abandoned appliances are still
dangerous – even if they will sit for “just a few days”. If
you are getting rid of your old appliance, please follow
the instructions below to help prevent accidents.
We strongly encourage responsible appliance recycling/
disposal methods. Check with your utility company or
visit www.recyclemyoldfridge.com for more information
on recycling your old appliance.
Remove doors.•
Leave shelves in place so children may not easily •
climb inside.
Have refrigerant removed by a qualied service •
technician.
4
nOtE
The exterior walls of the beverage cooler may become
quite warm as the compressor works to transfer heat
from the inside. Temperatures as much as 30° F
warmer than room temperature can be expected. For
this reason it is particularly important in hotter climates
to allow enough space for air circulation around your
appliance.
The beverage cooler must have all bottom corners resting
rmly on solid oor. The oor must be strong enough
to support a fully loaded beverage cooler. nOtE: It is
Very Important for your appliance to be level in order to
function properly. If the appliance is not leveled during
installation, the door may be misaligned and not close
or seal properly, causing cooling, frost, or moisture
problems.
After removing all interior and exterior packaging
materials, use a carpenter’s level to level the beverage
cooler from front-to-back. Adjust the leveling legs in
front, ½ bubble higher, so that the door closes easily
when left halfway open.
Wash any removable parts of the beverage cooler
interior, and exterior with mild detergent and warm
water. Wipe dry. Do not use harsh cleaners on these
surfaces.
Do not use razor blades or other sharp instruments,
which can scratch the appliance surface when
removing adhesive labels. Any glue left from the tape
can be removed with a mixture of warm water and
mild detergent, or touch the residue with the sticky
side of tape already removed. Do not remove the
serial plate.
Do not store food in your wine
cooler as interior temperature may not get cool enough
to prevent spoilage. In summer months or areas of high
humidity, the glass door may build up moisture. To
remove the moisture, wipe it away.
Place handle over the two mounting studs located at
top of door.
Use hex head screw driver or allen wrench to tighten
set screws from bottom to secure handle to door.
� Handle
ĸ Wooden Shelf Made of Beech
Ĺ Control Panel
� Glass Door
� Control Switch of Lamp
� Adjustable Leg
Placement of Wine Cooler
The wine cooler should be placed in dry and ventilated room. The location of
the wine cooler should not be irradiated by direct sunshine. The wine cooler
should be far away from heating sources, such as: cooking stove or heating
radiator. If the wine cooler has to be placed near heating source, please adopt
proper heating insulation board for insulation or keep the wine cooler at least
the following minimum distances away from the heating sources:
For electric stove: 3 .
For oil or coal stove: 30 .
Replacement of Door Hinge
The door hinges of this wine cooler can be interchanged between the left and
right sides.
Installation of Handle
1. Set the handle on the fixation shaft.
Fixation Shaft of Handle
Set Handle
2. Screw down the fixation pins of the handle with screw driver.
- 7 -
Mounting stud
Locate handle
Set screws
InStALLAtIOn
This Use & Care Guide provides general operating
instructions for your model. Use the appliance only as
instructed in this Use & Care Guide.
Choose a place that is near a grounded electrical •
outlet. use an extension cord or an adapter
plug.
For optimal performance, it is recommended •
that you install the appliance where the ambient
temperature is between 70 and 78 degrees
fahrenheit.
Allow space around the unit for good air circulation. •
Leave a 2 inch space on the back and sides of the
wine cooler for adequate circulation.
Be sure the appliance stays in the upright position •
during transport.
Keep the appliance from any hazardous or •
combustible agents.
5
The glass door can be opened from left to right and vice
versa. Should you desire to change the opening direction,
please follow these instructions.
nOtE
All parts removed must be saved to do the
reinstallation of the door.
Remove top cap. Remove the three screws that hold
the upper hinge (right side) to the top of the cabinet.
See Fig. 1.
Carefully remove top hinge (See Fig. 1.), then lift the
door up off of bottom hinge and place it on a padded
surface to prevent scratching it. See Fig. 2.
Remove the three button plugs from the upper left
corner of the cabinet and transfer them to the holes
on the opposite side. Be sure to press the button
plugs rmly into the holes. See Fig. 1.
Remove three screws that hold the bottom hinge to
lower end of cabinet. Remove the three button plugs
from lower LH corner and transfer to holes where
bottom hinge was just removed. See Fig. 3.
Unscrew pins from both hinges and transfer to
threaded hole on opposite side. See Fig. 4. Re-install
bottom hinge in LH corner of cabinet using same
three screws removed in Step 4.
On bottom edge of door, transfer door stop bracket
and bushing to holes on opposite side. See Fig. 6.
On top edge of door, transfer the button plugs and
bushing to hole on opposite side. See Fig. 7.
Place bottom LH corner of door onto lower hinge,
then install top hinge to cabinet. Make sure door
is level and it seals properly against cabinet, then
securely fasten three screws. See Fig. 7. Snap top
cap back onto hinge.
Chart 2
Step 7:Remove the bolt on the bottom of the door by screwdriver�(see chart
3)
Step 8:Remove the screw� and the block �,then set them on the left side.(see
chart 3)
ľ
ļ
Ľ
Chart 3
Step 9:Change the hinge axis� from the right hole to left hole(see chart 4)
Ŀ
Chart 4
Step 10:Use knife to remove the parts�,see chart 5.
- 8 -
Screws
Top cap
Bushing
Hinge
� Handle
ĸ Wooden Shelf Made of Beech
Ĺ Control Panel
� Glass Door
� Control Switch of Lamp
� Adjustment Leg
Door Reversal Instructions:
You can reverse the door swing if you change the position of the hinge(�) ,pls
follow the steps below:
Step 1:Close the door and use the knife carefully to remove the parts�ǃ�(see
chart 1)
Step 2:Remove the hinge coverĹ(see chart 1)
Step 3:Remove the screws by cross-screwdriverĺ(see chart 1)
Step 4:Remove the top hingeĻ(see chart 1)
Step 5:Remove the bolt by screwdriverļ(see chart 1)
ĸ
ķ
Ĺ
ĺ
Ļ
ļ
Chart 1
Step 6:Open the door and lift it up carefully then remove it,see chart 2.
- 7 -
Button plugs
Step 11:Loosen the bolt� and bottom hinge�ˈthen replace the parts on the
left and right sideˈthen assemble the parts,see chart 6.
ĸ
ŀ
ĺ
Chart 5
Chart 6
Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see
chart 7.
ŋ
Chart 7
Step 13:Assemble the door on the bottom hinge�ˈthen reset the door bolt�
- 9 -
Move pin to
opposite hole
(upper and
lower hinges)
Step 11:Loosen the bolt� and bottom hinge�ˈthen replace the parts on the
left and right sideˈthen assemble the parts,see chart 6.
ĸ
ŀ
ĺ
Chart 5
Chart 6
Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see
chart 7.
ŋ
Chart 7
Step 13:Assemble the door on the bottom hinge�ˈthen reset the door bolt�
- 9 -
Button plugs
Screws
Hinge
Step 11:Loosen the bolt� and bottom hinge�ˈthen replace the parts on the
left and right sideˈthen assemble the parts,see chart 6.
ĸ
ŀ
ĺ
Chart 5
Chart 6
Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see
chart 7.
ŋ
Chart 7
Step 13:Assemble the door on the bottom hinge�ˈthen reset the door bolt�
- 9 -
Button plugs
Screws
InStALLAtIOn
6
and fix the top hinge on the door,to make the door level,see chart 8.
Step 14:Check the sealing of the door,then refit the parts �ǃ�.
Chart 8
Placement of Wine Cooler
The wine cooler should be placed in dry and ventilated room. The location of
the wine cooler should not be irradiated by direct sunshine. The wine cooler
should be far away from heating sources, such as: cooking stove or heating
radiator. If the wine cooler has to be placed near heating source, please adopt
proper heating insulation board for insulation or keep the wine cooler at least
the following minimum distances away from the heating sources:
For electric stove: 3 .
For oil or coal stove: 30 .
Replacement of Door Hinge
The door hinges of this wine cooler can be interchanged between the left and
right sides.
Installation of Handle
1. Set the handle on the fixation shaft.
- 10 -
Chart 2
Step 7:Remove the bolt on the bottom of the door by screwdriver�(see chart
3)
Step 8:Remove the screw� and the block �,then set them on the left side.(see
chart 3)
ľ
ļ
Ľ
Chart 3
Step 9:Change the hinge axis� from the right hole to left hole(see chart 4)
Ŀ
Chart 4
Step 10:Use knife to remove the parts�,see chart 5.
- 8 -
Bushing
Stop
bracket
Install the beverage cooler in
the coolest part of a dry and
ventilated room, out of direct
sunlight and away from heating
ducts or registers. Do not place
the beverage cooler next to heat-
producing appliances such as a
range, oven or dishwasher.
Level the beverage cooler so the door close tightly.
Do not over crowd the beverage cooler or block
cold air vents. Doing so causes the beverage cooler
to run longer and use more energy. Shelves should
not be lined with aluminum foil, wax paper or paper
toweling. Liners interfere with cold air circulation,
making the beverage cooler less efcient.
Wipe containers dry before placing them in the
beverage cooler. This cuts down on moisture build-up
inside the unit.
Organize the beverage cooler to reduce door
openings. Remove as many items as needed at one
time and close the door as soon as possible.
InStALLAtIOn
7
tEMpERAtuRE cOntROLS
For best performance, allow 4 hours for the wine/beverage cooler to cool down completely. The wine/beverage cooler
will run continuously for the rst several hours.
Multi-position adjustable interior shelves can be moved to
any position for larger or smaller packages. The shipping
spacers that stabilize the shelves for shipping should be
removed and discarded. The Beverage Cooler comes
equipped with three glass shelves.
The light comes on automatically when the door is
opened. The light can also be turned on and off by
fEAtuRES
Indication of Temperature in Lower Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature decrease 1°C.
Indication of Temperature in Upper Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature decrease 1°C.
: Temperature display.
Light: Lighting button for LED lamp; it controls the on/off of lamp.
Power: On/off button used to turn on/off all load.
Press Light and Power together for 2 seconds and you can convert between
fahrenheit temperature and Celsius temperature.
Notice!
z The default temperature is 10/10°C, and the temperature after power
failure will be the temperature set before the power failure.
z To elongate the service life of compressor, please wait for at least 5
minutes before the wine cooler is restarted after power failure.
z Failure display
z If there is failure on the sensor, the screen may display failure code, such
as: E and F. When the screen displays the above-mentioned errors, please
do not disassemble it for check by yourself. You should contact local
after-sales service personnel for repair.
z If the temperature in the cooler is too low, it will display “L”.
When the temperature in the cooler is too high, the screen will display “H”
and will flash; under this state, the buzzer will buzz until 30 seconds; one
minute later, the buzzer will continue to give alarm in the next 30 seconds; after
the alarm is given for three times, it will not give alarm any more. You can
press any key to cancel sound alarm.
z When you put a lot of wines together in the cooler, the temperature in the
cooler may rise temporarily.
- 10 -
This button turns the light ON and OFF.
This buttons turns the power ON and OFF.
Press both and button’s at the same time to change between Fahrenheit and Celsius temperatures.
The default temperature for the beverage cooler is 41°F (5°C). The temperature after power failure will be the
temperature set before the power failure.
To prolong the life of compressor, please wait for at least 5 minutes before the unit is restarted after power failure.
If “E” and “F” are displayed, please contact local service personnel for repair.
If the temperature in the cooler is too low, it will display “L”.
If the temperature in the cooler is too high, the screen will display “H” and will ash. Under this state, the buzzer
will buzz for 30 seconds. One minute later, the buzzer will continue to buzz for the next 30 seconds. After three
times, the alarm will not buzz any more. You can press any key to cancel sound alarm.
Storing too many cans or bottles in the cooler may cause the temperature in the cooler to rise temporarily.
Indication of Temperature in Lower Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature decrease 1°C.
Indication of Temperature in Upper Chamber
: Press this button once and the temperature increase 1°C.
: Press this button once and the temperature decrease 1°C.
: Temperature display.
Light: Lighting button for LED lamp; it controls the on/off of lamp.
Power: On/off button used to turn on/off all load.
Press Light and Power together for 2 seconds and you can convert between
fahrenheit temperature and Celsius temperature.
Notice!
z The default temperature is 10/10°C, and the temperature after power
failure will be the temperature set before the power failure.
z To elongate the service life of compressor, please wait for at least 5
minutes before the wine cooler is restarted after power failure.
z Failure display
z If there is failure on the sensor, the screen may display failure code, such
as: E and F. When the screen displays the above-mentioned errors, please
do not disassemble it for check by yourself. You should contact local
after-sales service personnel for repair.
z If the temperature in the cooler is too low, it will display “L”.
When the temperature in the cooler is too high, the screen will display “H”
and will flash; under this state, the buzzer will buzz until 30 seconds; one
minute later, the buzzer will continue to give alarm in the next 30 seconds; after
the alarm is given for three times, it will not give alarm any more. You can
press any key to cancel sound alarm.
z When you put a lot of wines together in the cooler, the temperature in the
cooler may rise temporarily.
- 10 -
Press this button once to increase temperature 1° F/C.
Press this button once to decrease temperature 1° F/C.
pressing the “Light” button on the control panel. Press
the button twice to keep the light on when the door is
closed.
This unit is equipped with a lock near the bottom of the
door. Two keys are provided. Keep the keys out of reach
of children.
1. The beverage cooler can be operated by adjusting the temperature control buttons (up arrow and down arrow)
to the various settings.
2. The new desired temperature will ash on the display for a few seconds and then switch back to the actual
temperature which will gradually change until setpoint is reached.
The temperature range MIN and MAX is 33° - 50°F (1° - 10°C).
8
cARE AnD cLEAnInG
Before cleaning, turn the temperature control to OFF,
unplug the beverage cooler and remove the bottles.
Clean your beberage cooler once every two months.
Wash inside surfaces of the beverage cooler with
a solution of two tablespoons of baking soda in one quart
(1.136 litres) warm water. Rinse and dry. Wring excess
water out of the sponge or cloth when cleaning in the
area of the controls, or any electrical parts.
Wash the removable parts with the baking soda solution
mentioned above, or mild detergent and warm water.
Rinse and dry. Never use metallic scouring pads,
brushes, abrasive cleaners, or alkaline solutions on any
surface. Do not wash removable parts in a dishwasher.
Wash the cabinet with warm water and mild
liquid detergent. Rinse well and wipe dry with a clean
soft cloth.
Be sure and protect the door gasket. It should be
kept clean at all times.
If the plastic parts in the beverage cooler remain
contaminated by oil (animal or vegetable) for a long
period of time, they will age and crack easily. Please
clean them on a regular basis.
If the beverage cooler will not be used for several
months:
Remove all wine bottles and unplug the power cord.
Clean and dry the interior thoroughly.
Leave the wine cooler door open slightly, blocking it
open if necessary, to prevent odor and mold growth.
Moving: When moving the beverage cooler, follow these
guidelines to prevent damage:
Disconnect the power cord plug from the wall outlet.
Remove wine bottles and clean the beverage cooler.
Secure all loose items by taping them securely in
place to prevent damage.
In a moving vehicle, secure the beverage cooler in an
upright position to prevent movement. Also, protect
the outside of the beverage cooler with a blanket or
similar item.
WARnInG
If leaving the beverage cooler door open while on
vacation, make certain that children cannot climb inside
and become entrapped.
1 Handle
2 Control panel
3 Glass shelves
4 Glass door
5 Light switch
6 Adjustable legs
1
2
3
4
5
6
9
cAuSE cORREctIOn
WInE cOOLER OpERAtIOn
Appliance is plugged into a •
circuit that has a ground fault
interrupt.
Temperature control is in the •
OFF position.
Appliance may not be plugged •
in, or plug may be loose.
House fuse blown or tripped
•
circuit breaker.
Power outage.•
Use another circuit. If you are unsure about the outlet, •
have it checked by a certied technician.
See • section.
Ensure plug is tightly pushed into outlet.•
Check/replace fuse with a 15 amp time-delay fuse. Reset •
circuit breaker.
Check house lights. Call local Electric Company.•
Room or outside weather is •
hot.
Appliance has recently been •
disconnected for a period of
time.
Door is opened too frequently •
or too long.
Door may be slightly open.•
Temperature control is set too •
low.
Door gasket is dirty, worn, •
cracked, or poorly tted.
It’s normal for the appliance to work harder under these •
conditions.
It takes 4 hours for the • Appliance to cool down completely.
Warm air entering the appliance causes it to run more. •
Open doors less often.
See • section.
Turn control knob to a warmer setting. Allow several hours •
for the temperature to stabilize.
Clean or change gasket. Leaks in the door seal will cause •
appliance to run longer in order to maintain desired
temperature.
Temperature control is set too
•
low.
Turn the control to a warmer setting. Allow several hours •
for the temperature to stabilize.
Temperature control is set too
•
warm.
Door is opened too frequently •
or too long.
Door may not be seating •
properly.
Large amounts of warm or hot •
food has been stored recently.
Appliance has recently been •
disconnected for a period of
time.
Turn control to a colder setting. Allow several hours for the •
temperature to stabilize.
Warm air entering the appliance causes it to run more. •
Open doors less often.
See
• section.
Warm food will cause Beverage Cooler to run more until •
the desired temperature is reached.
It takes 4 hours for the appliance to cool down completely.•
-
The external walls can be as •
much as 30°F warmer than
room temperature.
This is normal while the compressor works to transfer heat •
from inside the cabinet.
SOunD AnD nOISE
Modern beverage coolers have •
increased storage capacity and
more stable temperatures.
They require a high efciency
compressor
This is normal. When the surrounding noise level is low,
•
you might hear the compressor running while it cools the
interior
Visit our web site at
www.frigidaire.com.
1-800-944-9044 (United States)
1-800-265-8352 (Canada)
10
cAuSE cORREctIOn
Appliance operates at higher •
pressures during the start of the
ON cycle.
This is normal. Sound will level off or disappear as refrig-
•
erator continues to run.
Exterior thermostat has acti-
•
vated the heater or fan.
This is normal.
•
-
Metal parts undergo expansion •
and contraction, as in hot water
pipes.
This is normal. Sound will level off or disappear as Bever-•
age Cooler continues to run.
-
Refrigerant is circulating
•
throughout the system.
This is normal.•
Appliance• is not level. It rocks
on the oor when it is moved
slightly.
Level the unit. Refer to leveling instructions in the •
section.
Cold control turning the Wine
•
Cooler OFF and ON.
This is normal.•
Weather is hot and humid.•
Door may not be seating •
properly.
Door is kept open too long, or •
opened too frequently.
This is normal.•
See • section.
Open the door less often.•
Door may not be seating •
properly, causing the cold air
from inside the beverage cooler
to meet warm moist air from
outside.
See
• section.
Interior needs to be cleaned.
• Clean interior with sponge, warm water, and baking soda.•
Appliance
• is not level. It rocks
on the oor when it is moved
slightly.
This condition may force the cabinet out of square and •
misalign the door. Refer to “Leveling’ in the
section.
11
MAjOR AppLIAncE WARRAnty
Your appliance is covered by a one year limited warranty. For one year from your original date of
purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove
to be defective in materials or workmanship when such appliance is installed, used and maintained in
accordance with the provided instructions.
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased “as-is” are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances
not in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc.,which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air lters, water lters, other consumables, or
knobs, handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the nish of appliance or home incurred during installation, including but not limited to oors,
cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other than
genuine Electrolux parts or parts obtained from persons other than authorized service companies; or
external causes such as abuse, misuse, inadequate power supply, accidents, res, or acts of God.
DIScLAIMER Of IMpLIED WARRAntIES; LIMItAtIOn Of REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT
REPAIR OR REPLACEMENT AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES, INCLUDING
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR
OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX SHALL NOT
BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL
EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED
WARRANTY. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES, SO THESE
LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WRITTEN WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.
Service under this warranty must be obtained by contacting Electrolux at the addresses or phone
numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by Electrolux Canada Corp.
Electrolux authorizes no person to change or add to any obligations under this warranty. Obligations for service and parts under
this warranty must be performed by Electrolux or an authorized service company. Product features or speci cations as described
or illustrated are subject to change without notice.
uSA
Electrolux Major Appliances
North America
P.O. Box 212378
Augusta, GA 30907
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga, Ontario, Canada
L5V 3E4
