Loading ...
Loading ...
Loading ...
PURESOURCE MB iCE ANDWATER FRONT FILTER
(SOME MODELS)
filter before reinstalling the refrigerator. The dispenser system
wiII also operate without filtration (with filter cartridge removed
and bypass installed).
System Startup:
Water supply does not need to be turned off, however, do not
use ice and water dispenser while installing fiIter.
The filter cartridge has already been installed in the filter
housing at the factory. Refer to the How T,_e Water Dispenser
Works section to properly fill the system with water.
Order new filter
cartridges through the
dealer where you
bought the refrigerator,
contact the Consumer Cartridge
Assistance Center at 1-
800-944-9044, or go to
our web site at
www.friqidaire.com. It
might be good to order
some filter cartridges
when you first install
and Cmick Push
your refrigerator. Be Toinstall ToRe!ease
sure to ask for the
WP2CBMB replacement
cartridge.
ii
ii
The PureSource MB Ice and Water Filter System
MBFC 2003 with the PureSource MB cartridge
WF2CBMB is tested and certified by NSF
International, the nationaJly recognized and
respected, not for profit, certification organization
for public health safety. The PureSource MB Filter system is
tested and certified to ANSI/NSF Standards 42 and 53. See
performance data sheet for specifications. This system should
not be used on water that is microbiologicalIy unsafe or with
water of unknown quality unless the water has been
adequately disinfected before or after traveling through the
fiJtration system.
,, Rated Capacity - 250 gallons
,, Rated service flow - .5 GPM
,, Maximum Rated Pressure - 100 PSI
,, Maximum Operating Temp. - 100 ° F
To change filter:
It is not necessary to turn the water supply off to change the
filter,
1. Set ice maker wire signal arm to the OFF (up) position (side
mounted) or the ice maker's On/Off power switch turned Off-set
to the "O" position (rear mounted).
2. Push the Filter Release Button, located to the right of the
filter cartridge, to release the filter from the housing. To
minimize the possibility of the filter failing out of the
housing during removal, it would be best to hold the
fiJter as it moves out toward you.
3. Pull the old filter cartridge straight out of the housing.
4. Discard the old fiJter.
5. Remove the new filter cartridge from the packaging and
insert into the filter housing the same way the old one
came out.
6. When the cartridge is almost in, you wiII fee! it stop against
the clip assembly in the back of the housing. The clip
assembly holds the filter cartridge firmly in place. At this
point, you will need to push firmly until the cartridge
snaps fuJJyin place. When completely in place, the front of
the filter cartridge will be flush with the front of the housing.
7. Set ice maker wire signal arm to the ON (down) position (side
mounted) or the ice maker's On/Off power switch is turned On-
set to the "l" position. (rear mounted).
8. Fill a glass with water. As you are doing this, check for
leaks at the filter housing. There will be noticable spurts
and sputters as the system pushes the air out through the
system and out the dispenser nozzle. This is normal.
9. After you have run one giass of water, continue to flush the
system for approximately 3 minutes to assure that the
purest water possible is stored in the water storage tank.
Changing the Filter:
Water conditions vary throughout the world, but changing the
water filter every
6 - 9 months normally will ensure the highest possible water
quality. The Filter Status light will turn red after approximately
250 gallons of water has flowed through the ice and water
dispenser. Also, if the filter has been in a refrigerator that has not
been in use for awhile (during moving for example), change the
* White Westinghouse uses the name CrystalClear instead of PureSource, but they are the same filter.
17
Loading ...
Loading ...
Loading ...