Loading ...
Loading ...
Loading ...
PURESOURCE2 TM* iCE ANDWATER FRONT FILTER
(SOME MODELS)
filter before reinstalling the refrigerator. The dispenser system
will also operate without filtration (with filter cartridge removed
and bypass installed).
System Startup:
Water supply does not need to be turned off, however, do not
use ice and water dispenser while instalIing filter.
The filter cartridge has already been installed in the filter
housing at the factory. Refer to the How T,_e Water Dispenser
Works section to properly fill the system with water.
Order new filter
cartridges through the
dealer where you
bought the refrigerator,
contact the Consumer
Assistance Center at 1-
800-944-9044, or go to
our web site at
www.friqidaire.com. It
might be good to order
some filter cartridges
when you first install
your refrigerator. Be
sure to ask for the FC-
100 PureSource TM*
replacement cartridge.
and CUick Push Button
To hstall ToBe!ease
g
The PureSoume2 rM_Ice and Water Filter
System NGFC 2000 with the PureSource2 rM_
cartridge FC 100 is tested and certified by
NSF International, the nationally recognized
and respected, not for profit, certification
organization for public heaith safety. The PureSource2 rM_
Filter system is tested and certified to ANSI/NSF Standards
42 and 53. See performance data sheet for specifications.
This system should not be used on water that is
microbiologically unsafe or with water of unknown quality
unless the water has been adequately disinfected before or
after traveling through the filtration system.
,, Rated Capacity - 400 gallons
,, Rated service flow - .5 GPM
o Maximum Rated Pressure - 100 PSI
,, Maximum Operating Temp. - 100 ° F
Changing the Filter:
Water conditions vary throughout the world, but changing the
water filter every
6 - 9 months norma!ly will ensure the highest possible water
quality'. The Filter Status light will turn red after approximately
400 gallons of water has flowed through the ice and water
dispenser. Also, if the filter has been in a refrigerator that has not
been in use for awhile (during moving for example), change the
To change filter:
It is not necessary to turn the water supply off to change the
filter.
1. Set ice maker wire signal arm to the OFF (up) position (side
mounted) or the ice maker's On/Off power switch turned Off-set
to the "O" position (rear mounted).
2. Push the Filter Release Button, located to the right of the
filter cartridge, to release the filter from the housing. To
minimize the possibility of the filter failing out of the
housing during removal, it would be best to hold the
filter as it moves out toward you.
3. Pull the old filter cartridge straight out of the housing.
4. Discard the old filter.
5. Remove the new filter cartridge from the packaging and
insert into the filter housing the same way the old one
came out.
6. When the cartridge is almost in, you will fee! it stop against
the clip assembly in the back of the housing. The clip
assembly holds the filter cartridge firmly in place. At this
point, you will need to push firmly until the cartridge
snaps fully in place. When completely in place, the front of
the filter cartridge will be flush with the front of the housing.
7. Set ice maker wire signal arm to the ON (down) position (side
mounted) or the ice maker's On/Off power switch is turned On-
set to the "F position. (rear mounted).
8. Fill a glass with water. As you are doing this, check for
leaks at the filter housing. There will be noticable spurts
and sputters as the system pushes the air out through the
system and out the dispenser nozzle. This is normal.
9. After you have run one glass of water, continue to flush the
system for approximately 3 minutes to assure that the
purest water possible is stored in the water storage tank.
ii
* White Westinghouse uses the name CrystalClear instead of PureSource, but they are the same filter.
16
Loading ...
Loading ...
Loading ...